Part No |
Description |
NEMA 12 Enclosure |
Ametek Gemco NEMA 12 Enclosure for AHM Panels |
004560058 |
Ametek Gemco Screw on a 1025D Foot & Palm Switch Item 5 1/8 |
01-533114LXX |
Ametek Gemco Cable. Resolver Cable 22 AWG., 3 Twisted Pair with Shield. Priced per Foot |
014570001 |
Ametek Gemco Bearing 3/4 (Inch Bore with Flanges |
01533002L100 |
Ametek Gemco Cable. 100 Foot Bulk Resolver Cable for single Turn Resolvers, 22 AWG., 4 twisted Pairs with shield Price per foot / $ 2.00 Add length required at the end of the part number for other lengths (15LB) |
01533002L2000 |
Ametek Gemco Cable. 2000 Foot Bulk Resolver Cable for single Turn Resolvers, 22 AWG., 4 twisted Pairs with shield Price per foot / $ 2.00 Add length required at the end of the part number for other lengths (15LB) |
01533002L300 |
Ametek Gemco Cable. 300 Foot Bulk Resolver Cable for single Turn Resolvers, 22 AWG., 4 twisted Pairs with shield Price per foot / $ 2.00 Add length required at the end of the part number for other lengths |
01533002LXX |
Ametek Gemco Cable. Bulk Resolver Cable for single Turn Resolvers, 22 AWG., 4 twisted Pairs with shield Price per foot. Add length required at the end of the part number XXX (<5LB) |
01591317 |
Ametek Gemco Fluid. Shell Transformer Oil. Standard Fluid for ET Brake Thrusters. Diala AX Transformer Fluid. Sold per LB. About 6 pounds per thruster |
01591318 |
Ametek Gemco Fluid. Silicone Fluid. Optional Fluid for ET Brake Thrusters. Wacker SWS-101-50. Sold per LB. About 6 pounds per thruster |
01591448 |
Ametek Gemco Cord. Teflon Cord, 1/8th Inch Diameter by 90 Foot |
04-570252 |
Ametek Gemco Rod End. Plastic Rod Ends |
04-570256 |
Ametek Gemco Rod End. Female 1/4 -28 UNC Thread Front Rod End. Attaches to the rod / pistion. For use with 955D & DQ, 955LC, 956A, S, LC & DQ LDT'S |
04234100 |
Ametek Gemco Relay, Double Pole, Double Throw, 240 Volt, 60 Hz, 25 Amp (1LB) |
04234700 |
Ametek Gemco Relay, Double Pole, Single Throw, 240 Volt |
04513135 |
Ametek Gemco EPROM. IC EPROM for a 1995-L Micro-Set Programmable Limit Switch. Programmed with ''- X '' Standard Software 128K (<1LB) |
04514195 |
Ametek Gemco Rectifier a component on rectifier E010326 |
04515173 |
Ametek Gemco Varistor on rectifier E010326 |
04517039 |
Ametek Gemco Intrinsically Safe Barrier. Consult Factory |
04517214 |
Ametek Gemco Panel Mount Bracket for Barrier. Consult Factory |
04519072 |
Ametek Gemco Transformer on rectifier panel E0103026. 500 VA, 1 PH, 50 / 60 Hz, 380 to 600 Volt Primary, 115 / 230 Volt Secondary |
04519135 |
Ametek Gemco Transformer used on a rectifier panel, 100 VA, 230 Volt PR1, 56VCT Sec., Triad FD8-56 |
04521186 |
Ametek Gemco Terminal Strip. 16 Place Terminal Strip used on programmer and output expansion module. 1995 Micro-Set PLS (<1LB) |
04521187 |
Ametek Gemco Terminal Strip. 24 Place Terminal Strip used on programmer and output expansion module. 1995 Micro-Set PLS (<1LB) |
04521210 |
Ametek Gemco Cable Assembly for the 950IS only. 6 Foot 2 Pin Euro Mini Straight Connector |
04523020 |
Ametek Gemco Relay. 1996 Ram-Set & Brake Monitor Relay on a 1992 Press-Set Controller (<1LB) |
04523022 |
Ametek Gemco Relay. Mechanical Output Relay SPDT 10 AMP, 24 VDC 1992 & 1995 PLS |
04523085 |
Ametek Gemco Timer on Delay used on a rectifier panel, 10 Sec Plug in, 8 Pin, 240 VAC 12/6 |
04523126 |
Ametek Gemco Relay. AC Solid State Relay, 3 AMP., 24 - 280 VAC |
04523127 |
Ametek Gemco Relay. DC Solid State Relay |
04535001 |
Ametek Gemco Resolver. Replacement resolver with wire leads but without connector (2LBS) Size 11 Single S Kearfott CR41093052-14 or Deltran # 11BRCX-300-L10/6 |
04535094 |
Ametek Gemco Resolver. Size 11 resolver, single shaft (internal resolver only, no housing) 11-BHW-40-F/F473 |
04537001 |
Ametek Gemco Switch. Snap Switch. S.P.D.T. Single Pole Double Throw (<1LB) 1/8 |
04537002 |
Ametek Gemco Switch. Snap Switch. S.P.D.T. Single Pole Double Throw 1/8 |
04537003 |
Ametek Gemco Micro Switch DPDT. Includes Roller & Arm (<1LB) 1/8 |
04537004 |
Ametek Gemco Switch used on the 2000 Series Limit Switch Assemblies, S.P.D.T., Includes Actuator Arm with Roller and Hardware. Can be wired for normally open or closed circuit. Plunger Side Normally Open Terminals, Opposite Plunger Side Normally Closed Terminals 16-204 (<1LB) 1/8 |
04537018 |
Ametek Gemco Switch. Precision Snap Switch with 1/2 Roller. Sq D # 9007-AB1-S1. 2000 Series GRLS 1/8 |
04537080 |
Ametek Gemco Key for a 1992 Press-Set Controller & a 1989 PLS (<1LB) |
04560001 |
Ametek Gemco Screw. Pan Head Machine Screw 6-32 x 1'' STL SLTD zinc & wax taptite (<1LB)
|
04562148 |
Ametek Gemco Jam Nut (<1LB) |
04564002 |
Ametek Gemco Woodruff Key |
04564012 |
Ametek Gemco Fastener. Retaining / Snap Ring. Truarc 5100-37 SZDB. Shaft to Worm Gear Fastener 200- Series |
04570001 |
Ametek Gemco Bearing. Sealed Ball Bearing with Mounting Flanges for a 1980 Series Limit Switch. NEMA 1, 4 or 12 Enclosures. 3/4 Inch I.D. (1LB) |
04570252 |
Ametek Gemco Rod Ends for the 956 LDT or Control Arm 955ARM Female Thread 1/4 -28 |
04573067 |
Ametek Gemco Motor 48 VDC Tach Generator |
04578121 |
Ametek Gemco Repair Kit. Repair Kit for the Master Cylinder Section of a New Style J54085 or a J054086 Power Cluster |
04578122 |
Ametek Gemco Repair Kit. Repair Kit for the Diaphragm on a New Style J054085 Power Cluster |
04578123 |
Ametek Gemco Repair Kit. Repair Kit for the Diaphragm on a New Style J054086 Power Cluster |
04580066 |
Ametek Gemco Coupling. .25 X .120 Bore . Used to connect the cam shaft and a resolver (1LB) |
04581003 |
Ametek Gemco Spring. Return Spring on a Foot Switch (<1LB) 7/7 |
04582015 |
Ametek Gemco Belt. O-Ring Belt, Cam box main shaft to tach generator drive belt (<1LB) |
10'' H 1 |
Ametek Gemco 10 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 425 LBS. / FT dynamic stopping torque. Includes Qty.1, 10 Inch Hydraulic Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 10 Inch Brake Weight 93 LBS. Overall Width 19 - 7/16 Inch , Height 19 - 7/16 Inch. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually operated. A 10 X 4 Inch Brake Wheel is not included. 7905 Actuator 222 LBS Gross |
10'' HM 1 |
Ametek Gemco 10 X 4.25 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 425 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 450 FT LBS. Includes one 10 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 220 LBS Net. |
10''-H-1 |
Ametek Gemco 10 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 425 LBS. / FT dynamic stopping torque. Includes Qty.1, 10 Inch Hydraulic Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 10 Inch Brake Weight 93 LBS. Overall Width 19 - 7/16 Inch , Height 19 - 7/16 Inch. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually operated. A 10 X 4 Inch Brake Wheel is not included. 7905 Actuator 222 LBS Gross |
10''-H-2 |
Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 400 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 10 Inch Hydraulic Brake Assemblies J002926, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. Brake Wheels are not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (189LBS) |
1025-1407 |
Ametek Gemco Foot Switch. Engineered product with a Reed Switch. Like a 1025-B-1SP-P B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 1SP = Reed Switch supplied P = Plain Cover, covers only the enclosure 1/6
|
1025-1421 |
Ametek Gemco Foot Switch. Type C Heavy Duty NEMA 4 Side Treadle Operated Foot Switch. 2 Single Pole Double Throw Switches. ( Each 1 N.O. - 1 N.C.) with special I.D originally done for United Airlines (7LBS) 1/06 |
1025-1423 |
Ametek Gemco Foot Switch use new part number 1025-B-1SP-P-X |
1025-A-1DP-S |
Ametek Gemco Foot Switch. Obsolete 4/1/06 see Type ''B'' Type ''A'' Standard Duty Treadle Operated Foot Switch, NEMA 1 Die Cast Enclosure, 1DP = One contact Block, 1 D.P.D.T. Double Pole Double Throw Switch, (2N.O. - 2 N.C.) 2 Position with Spring Return . Includes Protective Shield to prevent accidental treadle operation. 3/4 Inch Conduit Entrance (4LBS) |
1025-A-1DP-X |
Ametek Gemco Foot Switch. Obsolete 4/1/06 see Type ''B'', Type ''A'' Standard Duty Treadle Operated Foot Switch, NEMA 1 Die Cast Enclosure, 1SP = One contact Block, 1 D.P.D.T. Single Pole Double Throw Switch, (2N.O. - 2 N.C.) 2 Position with Spring Return. 3/4 Inch Conduit Entrance (2LBS) |
1025-A-1SP-S |
Ametek Gemco Foot Switch. Obsolete 4/1/06 see Type ''B'' Type ''A'' Standard Duty Treadle Operated Foot Switch, NEMA 1 Die Cast Enclosure, 1SP = One contact Block, 1 S.P.D.T. Single Pole Double Throw Switch, (1N.O. - 1 N.C.) 2 Position with Spring Return. Includes Protective Shield to prevent accidental treadle operation. 3/4 Inch Conduit Entrance (4LBS) |
1025-A-1SP-X |
Ametek Gemco Foot Switch. Obsolete 4/1/06 see Type ''B'',Type ''A'' Standard Duty Treadle Operated Foot Switch, NEMA 1 Die Cast Enclosure, 1SP = One contact Block, 1 S.P.D.T. Single Pole Double Throw Switch, (1N.O. - 1 N.C.) 2 Position with Spring Return. 3/4 Inch Conduit Entrance. |
1025-B-1A4-S-X |
Ametek Gemco Foot Switch. Heavy Duty NEMA 4 Treadle Foot Switch. 1A4 = 4 Way 5 Port, 1 Air Valve S = Treadle Shield for Top & Side Switch Protection X = No Switch Latch |
1025-B-1DP-P-X |
Ametek Gemco Foot & Palm Switches. Series 1025 Type B Heavy Duty NEMA 4 Treadle Operated Foot Switch. 1 Contact Block 1 D.P.D.T. Switch that can be wired for a normally open or closed circuit. Only the enclosure is covered. The foot pedal is not covered (5LBS) |
1025-B-1DP-S-X |
Ametek Gemco Foot Operated Switch B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 1DP = One D.P.D.T. Double Pole Double Throw Switch which can be wired for either Normally Open or Normally Closed Circuits S = Treadle Shield for Top & Side Protection
|
1025-B-1SP-G-X |
Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 1 SPDT ( 1 NO - 1NC ) with Treadle Guard to provide top protection from accidental operation |
1025-B-1SP-P-X |
Ametek Gemco Foot & Palm Switches. Series 1025 Type B Heavy Duty NEMA 4 Treadle Operated Foot Switch. 1 Contact Block 1 S.P.D.T. Switch that can be wired for a normally open or closed circuit. Only the enclosure is covered. The foot pedal is not covered (5LBS) |
1025-B-1SP-S-X |
Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle Operated Foot Switch. NEMA 4, One contact block, 1 SPDT ( One 1 NO - 1NC ), S Cover Option = Treadle Shield provides Top & Side Protection C-H 10251-H35C with Switch Type B (8LBS) |
1025-B-1SP-U-X |
Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle Operated Foot Switch. NEMA 4, One contact block, 1 SPDT ( One 1 NO - 1NC ), U Cover Option = Treadle Shield provides Top, Side and a Safety Gate which must be raised by the toe to gain access to the treadle (11LBS) |
1025-B-2DP-P-X |
Ametek Gemco Foot Operated Switch B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits X = No other options |
1025-B-2DP-S-L |
Ametek Gemco Foot Operated Switch. B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits S = Treadle Shield for Top & Side Protection L = Protective Shield |
1025-B-2DP-S-X |
Ametek Gemco Foot Operated Switch B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits S = Treadle Shield for Top & Side Protection
|
1025-B-2SP-G-X |
Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 2 SPDT ( Each 1 NO - 1NC ) with Treadle Guard to provide top protection from accidental operation |
1025-B-2SP-P-X |
Ametek Gemco Foot & Palm Switches. Series 1025 Type B Heavy Duty NEMA 4 Treadle Operated Foot Switch. 2 Contact Blocks, 2 S.P.D.T. Switches that can be wired for a normally open or closed circuits. Only the enclosure is covered. The foot pedal is not covered (5LBS) |
1025-B-2SP-S-X |
Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 2 SPDT ( Each 1 NO - 1NC ) with Treadle Shield providing Top & Side Guard protection from accidental operation |
1025-C-2DP-S |
Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case, Cover & Treadle. Two Contact Blocks, 2 D.P.D.T. Switches (Each 2 NO - 2 NC) with Protective Shields. Six nameplates are provided, ''START'' ''STOP'' ''FORWARD'' ''REVERSE'' two are blank for special markings. Case has Qty. 2, 3/4'' pipe tapped conduit entrances one of which is fitted with a pipe plug. (12LBS) |
1025-C-2DP-X |
Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case & Treadle. Two Contact Blocks, 2 D.P.D.T. Switches (Each 2 NO - 2 NC) Six nameplates are provided, ''START'' ''STOP'' ''FORWARD'' ''REVERSE'' two are blank for special markings. Case has Qty. 2, 3/4'' pipe tapped conduit entrances one of which is fitted with a pipe plug. (11LBS) |
1025-C-2SP-S |
Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case, Cover & Treadle. Two Contact Blocks, 2 S.P.D.T. Switches (Each 1 NO - 1 NC) with Protective Shields. Six nameplates are provided, ''START'' ''STOP'' ''FORWARD'' ''REVERSE'' two are blank for special markings. Case has Qty. 2, 3/4'' pipe tapped conduit entrances one of which is fitted with a pipe plug (11LBS) |
1025-C-2SP-X |
Ametek Gemco Switch. Foot Operated Switches, Type ''C'' Heavy Duty Side Treadle Operated Foot Switch. NEMA 4 Enclosure, Two Contact Blocks, Two Snap action Single Pole Double Throw Switches that can be wired for either Normally Open or Normally Closed Circuits. Six Name Plates are provided. START STOP FORWARD REVERSE & Two are blank for your custom marking (7LBS) |
1025-D-1SP |
Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. One S.P.D.T. Switch (1 NO - 1 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS) |
1025-D-2DP |
Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. Two D.P.D.T. Switch (2 NO - 2 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS) |
1025-D-2SP |
Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. One D.P.D.T. Switch (2 NO - 2 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS) |
10316H-169-1 |
Ametek Gemco 2006-402-L-1080-A |
10316H89A |
Ametek Gemco 1950-1-B-A-DO C-H Part # shown above |
104A020XXXX |
Ametek Gemco Thermistors. 9967 LUG Thermistor. MOTOGARD Controllers are designed for use with Positive Temperature Coefficient Thermistors. Thermistor is encapsulated in a special epoxy for rugged mechanical duty, severe environments and good thermal conductivity# 22 - 26 Teflon Insulated Leads. Specify desired length of the leads (<1LB) |
104A022XXXX |
Ametek Gemco Thermistors. 9967 SPRING LOADED PROBE Thermistor. MOTOGARD Controllers are designed for use with Positive Temperature Coefficient Thermistors. Thermistor is encapsulated in a special epoxy for rugged mechanical duty, severe environments and good thermal conductivity# 22 - 26 Teflon Insulated Leads. 7/16 Inch Diameter. 1/4 Inch NPT. Specify desired probe length, 2 to 6 Inches is standard. Specify lead length (<1LB) |
107085 |
Ametek Gemco Repair Kit, for a Moisture Ejection Valve. ISG SAP 1170357 |
107163002 |
Ametek Gemco Pressure Cluster Assembly, 1 X 8, with special piston for long static lines, like 54086 |
1090-A1 |
Ametek Gemco Obsolete 12 Bit unit. Replaced by 1090B1 a 14 Bit unit |
1090B1 |
Ametek Gemco Multibus High Speed Programmable Limit Switch. 14 Bit Resolution. Replaced 1090A1 |
115101-2 |
Ametek Gemco MOTOGARD 9966. Series 115 Over Temperature Protection System. 6 Inputs, 2 Triac Outputs 1-N.O. 1 N.C. Input Rating: 120 VAC + or - 10% Single Phase 50/60 Hz. Output Rating: 120 /240 Volts 5 amp continuous. Reset is automatic. Enclosure 5.5'' Wide X 4.25'' Long X 3.12'' High Potted in a NEMA 4 Steel Case (2LBS) |
120101 |
Ametek Gemco MOTOGARD 9966. Series 120 Over Temperature Protection System |
135101 |
Ametek Gemco MOTOGARD 9966. Series 135 Over Temperature Protection System |
14'' H 2 |
Ametek Gemco 14 Inch Hydraulic Brake System, Qty. 2, Brake Assemblies each capable of 0 to 600 LBS / FT Torque, Control Cylinder, Pedal, Fluid Reservoir Bleeder, 250 Foot of Tubing, 6 Armored Hoses, 3 Gallons of 21B Wagner Brake Fluid and Fittings, 6 Brackets, 6 Jam Nuts, 36 Tube Nuts, 6 Lock Washers, 15 Copper Gaskets, 85 Bushings, 85 Clamps, 7 Unions for a complete system, less brake wheels. |
14'' HM 1 |
Ametek Gemco 14 X 6.50 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 600 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 550 FT LBS. Includes one 14 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 289 LBS Net. |
14''-H-1 |
Ametek Gemco 14 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 600 LBS. / FT dynamic stopping torque. Includes Qty.1, 14 Inch Hydraulic Brake Assembly, DC Fluid Reservoir Bleeder, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 14 Inch Brake Weight 161 LBS. Overall Width 25 - 7/8 Inch, Height 28 - 1/2 Inch. A 7905 Brake Actuator is provided / used on a single brake system (320LBS) |
1500-H-L3-S9-N1-X |
Ametek BW Controls Induction Control Relay model 1500-H-L3-S9-N1-X, 440 VAC Line Voltage, 480VAC Secondary Voltage, Nema 1 Enclosure without any other options. |
1500-HL1-S30-C-X |
Ametek BW Controls Relay. Series 1500 Induction Control Relay. 110 volts Primary, 40 Volts Secondary |
1500F-L1-S7OCX |
Ametek BW Controls Induction Control Relay |
150101 |
Ametek Gemco MOTOGARD 9966. Series 150 Over Temperature Protection Systems provide immediate overheating protection for motors equipment enclosures, semiconductor heatsinks, sleeve bearings and other related machinery. For use with PTC Thermistors embedded in or in contact with the monitored surface. 1 Input, Form C Relay Output. 2 Triac Outputs 1-N.O. 1 N.C. Input Rating: 120 VAC + or - 10% Single Phase 50/60 Hz. Output Rating: 120 VAC for size 5 contactor coil. Reset is automatic. Enclosure 3.25'' Wide X 2.25'' Long X 2.50'' High. Potted in a polyester case. Conforms with NEC Requirements for integral motor thermal protection (1LB) |
16-204 |
Ametek Gemco Switch see AME-04537004 |
1746L-1 |
Ametek Gemco LDT Interface Card. Single Axis, One LDT Input. Specify LDT output if other than: CP, VPI or RS (2LBS) |
1746L-2 |
Ametek Gemco LDT Interface Card. Two Axis, Two LDT Inputs. Specify LDT output if other than: CP, VPI or RS (2LBS) |
1746R-1 |
Ametek Gemco Interface Card. Series 1746R Resolver Interface Card incorporates Allen-Bradley licensed technology for complete compatibility with A-B Series 1746 I/O Chassis. The unit monitors machine position from a resolver and delivers continues absolute position data at 12 bit (4,096 count) resolution and RPM data to the SLC processor. |
1746R-2 |
Ametek Gemco Interface Card. Series 1746R Resolver Interface Card incorporates Allen-Bradley licensed technology for complete compatibility with A-B Series 1746 I/O Chassis. The unit monitors machine position from a resolver and delivers continues absolute position data at 12 bit (4,096 count) resolution and RPM data to the SLC processor. Two axis resolver interface. Two resolver inputs or field configurable for one multi-turn dual resolver. |
17618 |
Ametek Gemco Washer on Spring Case Gasket Kit |
1771-PLS-B1 |
Ametek Gemco Ultra-High Speed Programmable Limit Switch (PLS) with 16 direct outputs from the front panel that update every 5 microseconds. A resolver based unit that incorporated Allen-Bradley technology and is completely compatible with the A-B Series 1771 I/O chassis. Internally powered by the PLC backplane. Resolver input with 14 bit (16,384 count) resolution and field programmable scale factor. Reset to Preset Inputs & Speed Compensation. This product incorporates patented technology which is licensed by Allen -Bradley Company Inc. Allen-Bradley is a registered trademark of Rockwell Corporation (3LBS) |
1771-PLS-C1 |
Ametek Gemco Programmable Limit Switch. Allen Bradley Series 1771 Compatible High Speed Programmable Limit Switch. Standard 14 Bit Resolution (4LBS) |
18'' H-2 |
Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 1800 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 18 Inch Hydraulic Brake Assemblies J002932, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. Brake Wheels are not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (670LBS) |
18'' HM 1 |
Ametek Gemco 18 X 8.50 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 900 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 700 FT LBS. Includes one 18 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 389 LBS Net. |
18''-H-1 |
Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 900 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty.1, 18 Inch Hydraulic Brake Assembly J002932, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 100 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.4, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. A Brake Wheel is not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (359LBS) |
1950-1-B-A-AO |
Ametek Gemco Switch 1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco 1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit B = Binder / Screw Terminals 4 A = Front Mounting AO = Switch Plunger operated via cam or roller follower U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC -50 to 185 Degree F Recommended replacement @ 15 million cycles (<1LB) |
1950-1-B-A-AR |
Ametek Gemco Switch 1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco 1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit B = Binder / Screw Terminals 4 A = Front Mounting A = Switch Plunger operated via cam or roller follower R = Rubber boot for addition protection form humidity and dust U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC -50 to 185 Degree F Recommended replacement @ 15 million cycles (<1LB) |
1950-1-B-A-BO |
Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Front Mounting, Lever & 1/2'' Dia. Roller Assembly |
1950-1-B-A-DO |
Ametek Gemco Switch. Precision Snap Action Switch Assembly. SPDT Single Pole Double Throw, Qty. 4 Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit, Front Mounting, Plunger Push Operator, 2006 Type K, U.L. Listed (<1LB) |
1950-1-B-A-DR |
Ametek Gemco Switch. Precision Snap Action Switch Assembly. 1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit, B = Binder Terminals, A = Front Mounting, DR = Plunger with Boot, Push Operated, U.L. Listed (<1LB) |
1950-1-C-A-BO |
Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, 915 / 917 Cycl-Set Terminals, Front Mount, Lever & 1/2 Inch Diameter Roller Assembly. |
1950-1-C-A-DO |
Ametek Gemco Switch. Precision Snap Action Limit Switch Assembly, Single Pole Double Throw / S.P.D.T., 4 screw terminals, can be wired for either Normally Open or Normally Closed Circuits. Front Mount, Plunger Push Operator. 915 / 917 Cycl-Set & 2006 K RS (<1LB) |
1950-1-D-A-AO |
Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Saddle Clamp Terminals, Front Mounting, Plunger Cam Operated |
1950-1-D-A-DO |
Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Saddle Clamp Terminals, Front Mounting, Plunger Push Operator ( Cycl-Set & 2006K RS ) |
1950-1-P-A-AO |
Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Plug-In Terminals, Front Mounting, Plunger Cam Operated |
1950-1-P-A-AR |
Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Plug-In Terminals, Front Mounting, Plunger Cam Operated, Plunger with boot-cam operator. |
1950-1404 |
Ametek Gemco Switch. Precision Snap Limit Switch Unit. Single Pole Double Throw (S.P.D.T.) Plunger OP Bind TE with Boot and Heavy Springs. For use with the Series 1970 Driv Cheks (<1LB) |
1950-1405 |
Ametek Gemco Switch. Precision Snap Limit Switch Unit. Double Pole Double Throw, Plunger Operated. Binder Terminals with Heavy Springs. 1970 Drive Chek (<1LB) |
1950-1406 |
Ametek Gemco Switch. Obsoleted in 2006, See 1950-1413. Precision SPST Slow Make - Slow Break Switch Assembly. N.C. Normally Closed. Special Purpose Switch. U.L. Listed For the 1980 Product Line (<1LB) |
1950-1408 |
Ametek Gemco Switch. SPDT Slow Make Slow Break. For products 915 / 917/ 2006 (<1LB) |
1950-1413 |
Ametek Gemco Switch. Precision Slow Make - Slow Break Single Pole Double Throw Switch Assembly. Can be wire for either a normally open or normally close circuit. 4 screw terminals on this switch. Replaces 1950-1406 which is obsolete (<1LB) |
1950-1414 |
Ametek Gemco Switch. Single Pole Double Throw with a Heavy Duty Spring for high vibration applications. Can be wired for normally open or closed circuits, 4 screw terminals. Replaces obsolete 1950-1416 but is not a Slow Make Slow Break Switch (<1LB) |
1950-1416 |
Ametek Gemco Switch. Obsolete 1/6 Precision Snap Switch, Single Pole Double Throw, Slow Make Slow Break with a Heavy duty / strong Spring for High Vibration Applications. Only one contact that is Normally Closed. Replaced by 1950-1414, though it is NOT an exact duplicate replacement, see specifications (<1LB) |
1950-4-B-A-AO |
Ametek Gemco Switch 1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco 4 = Double Pole Double Throw / D.P.D.T., Eight Screw Terminals, can be wired for either a Normally Open or Normally Close Circuits B = Binder / Screw Terminals 8 A = Front Mounting AO = Switch Plunger operated via cam or roller follower U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC -50 to 185 Degree F Recommended replacement @ 15 million cycles (<1LB) |
1950-4-B-A-AR |
Ametek Gemco Switch 1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco 4 = Double Pole Double Throw / D.P.D.T., Eight Screw Terminals, can be wired for either a Normally Open or Normally Close Circuits B = Binder / Screw Terminals 8 A = Front Mounting A = Switch Plunger operated via cam or roller follower R = Rubber boot for addition protection form humidity and dust U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC -50 to 185 Degree F Recommended replacement @ 15 million cycles (<1LB) |
1950-4-B-A-BR |
Ametek Gemco Switch. Precision Snap Limit Switch Unit. Double Pole Double Throw (D.P.D.T.) 2-NO / 2-NC, Plunger operated by Lever & 1/2 Inch Diameter Roller Assembly. Includes Boot |
1950-4-B-A-DO |
Ametek Gemco Switch. Precision Snap Action Switch Assembly. DPDT Double Pole Double Throw, Qty. 8 Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit, Front Mounting, Plunger Push Operator, 2006 Type K, U.L. Listed (<1LB) |
1950-4-C-A-DO |
Ametek Gemco Switch. Precision Snap Action Limit Switch Assembly. Double Pole Double Throw / D.P.D.T., Eight Screw Terminals, can be wired for either Normally Open or Normally Closed Circuits.Front Mount, Plunger Push Operator. 915 / 917 Cycl-Set & 2006 K RS (<1LB) |
1950-4-P-A-AO |
Ametek Gemco Switch. Precision Snap Limit Switch Unit. D.P.D.T. Double Pole Double Throw 2-N.O 2-N.C , Plug-In Type Binder, Front Mounting Arrangement, Plunger Cam Operated. |
1950G-1-B-A-AR |
Ametek Gemco Switch. Precision Snap Limit Switch Unit with Gold Contacts, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Front Mounting, Plunger with Boot, Cam Operated U.L. Listed (<1LB) 1/8 |
1970-104 |
Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 2 to 4 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator (9LBS) |
1970-106 |
Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 5 to 6 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator (13LBS) |
1970-108 |
Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 7 to 8 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator (16LBS) |
1970-112 |
Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 9 to 12 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator (19LBS) |
1970-116 |
Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 13 to 16 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator |
1970-120 |
Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 17 or 20 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek serves 3 purposes; a broken chain or belt detector via a supplied travel limit switch, spring loaded sub base for chain or belt tensioning and a shock and vibration isolator |
1970-1204 |
Ametek Gemco Drive Chek. Drive Check for a Series 1980 Rotating Cam Limit Switch. 2 to 4 Circuit Frame with a NEMA 4 / 12 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock / vibration isolator |
1970-1206 |
Ametek Gemco Drive Chek. Drive Check for a Series 1980 Rotating Cam Limit Switch. 5 to 6 Circuit Frame with a NEMA 4 / 12 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock / vibration isolator |
1970-1208 |
Ametek Gemco Drive Chek. Drive Check for a Series 1980 Rotating Cam Limit Switch. 7 to 8 Circuit Frame with a NEMA 4 / 12 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock / vibration isolator |
1970-1212 |
Ametek Gemco Drive Chek. Drive Check for a Series 1980 Rotating Cam Limit Switch. 5 to 6 Circuit Frame with a NEMA 12 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock / vibration isolator |
1970-124 |
Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 21 to 24 Circuit Frame with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock or vibration isolator. |
1980 |
Ametek Gemco Series 1980 Micro-Adjust Rotating Cam Limit Switch Switch Settings 4 to 356 Degrees without a Tool - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 Model 1980-106-R-DP-X 1 = NEMA 1 Enclosure 6 = Qty. 6, Independent Cams / Circuits / Switches R = Right Hand Shaft Extension DP = DPDT Switches = Double Pole Double Throw X = No Timing Dial or timing dial window
CAPE MAY NEW JERSEY MOVEABLE BRIDGE; Specification for rotating cam limit switch.
The contractor shall provide a rotating cam limit switch that meets the specification as called out below. The cam box shall have 16 circuits each consisting of a micro adjust cam capable of dwells from 4 degrees through 356 degrees utilizing two cam halves. The cams shall be adjusted by use of a cam adjustment tool supplied with the cam box and mounted inside of the enclosure on a bracket. The cams are adjusted through a 36:1 ratio pinion assembly that will rotate each half of a circuit cam 10 degrees for each complete adjustment hub turn. The micro-adjust cams shall maintain an accuracy and repeatability of 1/4 degree. Each circuit shall have a precision rugged duty snap action switch with double break contacts that are actuated at a uniform rate to give long life. Electrical switches shall be SPDT with one NO and one NC contact per switch. Switches shall be rated for at least 15 million cycles. The input shaft shall be a 3/4'' diameter made of 316 Stainless Steel having a # 606 woodruff key and can be located on the right end, left end or a double ended version can be specified. The enclosure, cover, latches, bearing flanges and flange bolts shall be constructed of 304 Stainless Steel meeting a NEMA 4X rating. The cam box shall utilize lifetime sealed ball bearings for the input shaft. The cam box shall be supplied standard with a three year warranty covering the entire unit. The cam box shall be manufactured by Ametek APT, Gemco division out of Clawson Michigan with no substitutions allowed.
|
1980-101-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-101-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 01 = 1 Independent Cam / Circuit / Switch R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (10LBS) |
1980-102-L-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-102-L-DP-X Series 1980 1 = NEMA 1 Enclosure 02 = 2 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw Snap Action Switch U.L. Listed X = No Timing Dial or Dial Window is provided 3 Year Warranty (11 LBS) |
1980-102-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-102-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 02 = 2 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (11LBS) |
1980-102-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-102-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 02 = 2 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty |
1980-103-L-DP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-DP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (11LBS) |
1980-103-L-DP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-DP-TD2 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD2 = Timing Dial Labeled for C.C.W. Rotation 3 Year Limited Warranty (11LBS) |
1980-103-L-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-DP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-103-L-GSP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-GSP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension GSP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided |
1980-103-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (11LBS) |
1980-103-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-103-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03= 3 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD1 = Timing Dial Labeled for Clockwise Rotation 3 Year Warranty (12LBS) |
1980-103-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-103-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03= 3 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (12LBS) |
1980-104-D-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-D-DP-X Series 1980 1 = NEMA 1 Enclosure 4 = 4 Cams / Circuits / Switches D = Double Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw X = No Timing Dial or Dial Window is provided (13LBS) |
1980-104-D-DPP-R-X-S-200-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-D-DPP-R-X-S-200-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches D = Shaft Extension Opposite the Gear Box, Double Shaft 2 DPP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch with a Plug in Socket R = Rubber boot Option on the switch plunger for additional moisture & dust protection X = No Timing Dial S= Straight Drive Gear Reducer 200 = 200 to 1 Gear Ratio R = Right End Gear Reducer |
1980-104-D-GSP-R-X |
Ametek Gemco Rotating Cam Limit Switch like Model 1980-104-L-GSP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension GSPR = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts & Rubber Seals for additional dust & moisture protection X = No Timing Dial or Dial Window is to be provided (12LBS) |
1980-104-D-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-D-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Dual Shafts Extending from Enclosure, 2 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (14LBS) |
1980-104-D-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-D-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches D = Double Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is provided 3 Year Warranty (12LBS) |
1980-104-L-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-104-L-GSP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-GSP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension GSP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided
|
1980-104-L-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional moisture protection X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-104-L-SP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-TD2 Series 1980 1 = NEMA 1 Enclosure 4 = 4 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD2 = Timing Dial C.C.W. Counter Clock Wise Rotation |
1980-104-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-104-R-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-DP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 4 = 4 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (12LBS) |
1980-104-R-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-104-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (12LBS) |
1980-104-R-SP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (12LBS) |
1980-104-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-104-X-DP-X-S-10-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-DP-X-S-10-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 10 = 10 to 1 Gear Ratio R = Right End Gear Reducer (18LBS) |
1980-104-X-DP-X-S-1000-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-DP-X-S-1000-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 4 = 4 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 1000 = 1000 to 1 Gear Ratio R = Right End Gear Reducer Location |
1980-104-X-DP-X-S-25-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-DP-X-S-25-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 25 = 25 to 1 Gear Ratio R = Right End Gear Reducer (18LBS) |
1980-104-X-SP-X-R-400-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-SP-X-R-400-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox / no double shaft extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided R= Right Angle Gear Reducer 400 = 400 to 1 Gear Ratio R1 = Right End Gear Reducer Shaft Location 1 |
1980-104-X-SP-X-R-5-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-SP-X-R-5-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox / no double shaft extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided R= Right Angle Gear Reducer 5 = 5 to 1 Gear Ratio R1 = Right End Gear Reducer Shaft Location 1 |
1980-104-X-SP-X-R-8-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-SP-X-R-8-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 4 = 4 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial R= Right Angle Gear Reducer 8 = 8 to 1 Gear Ratio R1 = Right End Gear Reducer Shaft Location 1 |
1980-104-X-SP-X-S-200-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-SP-X-S-200-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 200 = 200 to 1 Gear Ratio R = Right End Shaft Location |
1980-105-L-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-105-L-SP-TD1 Series 1980 1 = NEMA 1 Enclosure 05 = 5 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw Snap Action Switches U.L. Listed TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Warranty |
1980-105-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-105-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 05 = 5 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (14LBS) |
1980-105-R-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-105-R-DP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 05 = 5 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch X = No Timing Dial or Dial Window is provided 3 Year Warranty (14LBS) |
1980-105-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-105-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 05 = 5 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation (14LBS) |
1980-105-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-105-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 05 = 5 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-105-X-SP-X-R-1-L7 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-105-X-SP-X-R-1-L7 Series 1980 1 = NEMA 1 Enclosure 05 = 5 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw Precision Snap Action Switches X = No Timing Dial R= Right Angle Gear Reducer 1 = 1 to 1 Gear Ratio L7 = Left End Gear Reducer Shaft Location 7 |
1980-105-X-SP-X-S-14-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-105-X-SP-X-S-14-R Series 1980 1 = NEMA 1 Enclosure 5 = 5 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw X = No Timing Dial S= Straight Drive Gear Reducer 14 = 14 to 1 Gear Ratio R = Right End Shaft Location |
1980-106-D-SP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-D-SP-TD2 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Dual Shafts Extending from Enclosure, 2 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD2 = Timing Dial Labeled for Counter Clock Wise Rotation 3 Year Limited Warranty (16LBS) |
1980-106-D-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-D-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches D = Double Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (14LBS) |
1980-106-L-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-L-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (14LBS) |
1980-106-L-SP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-L-SP-TD2 Series 1980 1 = NEMA 1 Enclosure 06 = 6 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD2 = Timing Dial Labeled for C.C.Wise Rotation 3 year Warranty |
1980-106-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 06 = 6 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (14LBS) |
1980-106-R-DP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-R-DP-TD2 Series 1980 1 = NEMA 1 Enclosure 06 = 6 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw Snap Action Switches TD2 = Timing Dial C.C.W. Counter Clock Wise Rotation 3 Year Warranty |
1980-106-R-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-R-DP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-106-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (12LBS) |
1980-106-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (14LBS) |
1980-106-X-DP-X-S-2-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-DP-X-S-2-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 06 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 2 = 2 to 1 Gear Ratio R = Right End Shaft Location |
1980-106-X-DP-X-S-4-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-DP-X-S-4-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 06 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 4 = 4 to 1 Gear Ratio R = Right End Shaft Location |
1980-106-X-SP-R-X-S-28-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-R-X-S-28-L Series 1980 1 = NEMA 1 Rated Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional moisture protection X = No Timing Dial or Dial Window is to be provided S= Straight Drive Gear Reducer 28 = 1 Gear Ratio L = Left End Shaft Location |
1980-106-X-SP-R-X-S-32-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-R-X-S-32-L Series 1980 1 = NEMA 1 Rated Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional moisture protection X = No Timing Dial or Dial Window is to be provided S= Straight Drive Gear Reducer 32 = 1 Gear Ratio L = Left End Shaft Location |
1980-106-X-SP-X-R-10-R2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-X-R-10-R2 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox / no double shaft extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided R= Right Angle Gear Reducer 10 = 10 to 1 Gear Ratio R1 = Right End Gear Reducer Shaft Location 1 |
1980-106-X-SP-X-R-5-L7 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-X-R-5-L7 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided R= Right Angle Gear Reducer 5 = 5 to 1 Gear Ratio L7 = Left End Gear Reducer Shaft Location 7 |
1980-106-X-SP-X-S-*-* |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-X-S-*-* Series 1980 1 = NEMA 1 Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw X = No Timing Dial S= Straight Drive Gear Reducer * = * Gear Ratio to be determined * = * Shaft Location to be determined |
1980-106-X-SP-X-S-200-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-X-S-200-R Series 1980 1 = NEMA 1 Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw X = No Timing Dial S= Straight Drive Gear Reducer 200 = 1 Gear Ratio R = Right End Shaft Location |
1980-107-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-107-L-SP-X Series 1980 1 = NEMA 1 Enclosure 7 = 7 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw X = No Timing Dial or Dial Window is provided |
1980-107-R-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-107-R-DP-X Series 1980 1 = NEMA 1 Enclosure 07 = 7 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw Snap Action Switches U.L. Listed X = No Timing Dial or Dial Window is provided 3 Year Warranty (14LBS) |
1980-107-R-SP-R-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-107-R-SP-R-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 07 = 7 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty |
1980-107-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-107-L-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 07 = 7 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD1 = Timing Dial Labeled for C.W. Rotation |
1980-107-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-107-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 07 = 7 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (16LBS) |
1980-107-X-SP-X-S-6-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-107-X-SP-X-S-6-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 07 = 7 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 6 = 6 to 1 Gear Ratio R = Right End Gear Reducer (22LBS) |
1980-108-D-SD-TW1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-108-R-SP-TW1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 8 = 8 Independent Cams / Circuits / Switches D = Double Shaft Extension, shafts exit from both ends of the enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TW1 = Timing Dial & Dial Window is to be provided Timing Dial Degrees Labeled for Clock Wise Rotation 3 Year Warranty Dimensions, use a 9 to 12 circuit enclosure drawing (22LBS) |
1980-108-D-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-108-D-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 8 = 8 Independent Cams / Circuits / Switches D = Double Shaft Extension, shafts exit from both ends of the enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (17LBS) |
1980-108-L-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-108-L-SP-TD1 Series 1980 1 = NEMA 1 Enclosure 08 = 8 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw Snap Action Switches U.L. Listed TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Warranty |
1980-108-L-SP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-TD2 Series 1980 1 = NEMA 1 Enclosure 8 = 8 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD2 = Timing Dial C.C.W. Counter Clock Wise Rotation |
1980-108-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-108-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (17LBS) |
1980-108-R-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-108-R-DP-X Series 1980 1 = NEMA 1 Enclosure 4 = 8 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw X = No Timing Dial or Dial Window is provided
|
1980-108-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-108-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 08 = 8 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (17LBS) |
1980-108-X-DP-R-X-S-8-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-108-X-DP-R-X-S-8-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 08 = 08 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch R = Rubber Boot on switch plunger for moisture & dust protection X = No Timing Dial S= Straight Drive Gear Reducer 8 = 8 to 1 Gear Ratio R = Right End Shaft Location (21LBS) |
1980-108-X-DP-X-S-8-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-108-X-DP-X-S-8-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 08 = 08 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 8 = 8 to 1 Gear Ratio R = Right End Shaft Location |
1980-109-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-109-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 09 = 9 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (21LBS) |
1980-109-X-DP-X-R-14-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-109-X-DP-X-R-14-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 09 = 9 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox / no double shaft extension DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided R= Right Angle Gear Reducer 14 = 14 to 1 Gear Ratio R1 = Right End Gear Reducer Shaft Location 1 |
1980-110-D-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-110-D-SP-TD1 Series 1980 1 = NEMA 1 Enclosure 10 = 10 Cams / Circuits / Switches D = Double Shaft Extension (2) from enclosure SP = SPDT Switches / Single Pole Double Throw TD1 = Timing Dial Labeled for C.W. Rotation (21LBS) |
1980-110-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-110-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 10 = 10 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty |
1980-110-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-110-R-SP-X Series 1980 1 = NEMA 1 Enclosure 10 = 10 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw X = No Timing Dial or Dial Window is provided (21LBS) |
1980-111-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-111-R-SP-TD1 Series 1980 1 = NEMA 1 Enclosure 11= 11 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD1 = Timing Dial Labeled for C.W. Rotation |
1980-111-R-SP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-111-R-SP-TD2 Series 1980 1 = NEMA 1 Enclosure 11= 11 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD2 = Timing Dial Labeled for C.C.W. Rotation |
1980-112-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-112-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 12 = 12 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (29LBS) |
1980-112-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-112-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 12 = 12 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty |
1980-112-X-SP-R-X-S-6-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-112-X-SP-X-S-6-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 12 = 12 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch R = Rubber Boot / Seal on the Switch Plunger for additional moisture or dust protection X = No Timing Dial S= Straight Drive Gear Reducer 6 = 6 to 1 Gear Ratio R = Right End Shaft Location |
1980-112-X-SP-X-R-5-L1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-112-X-SP-X-R-5-L1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 12 = 12 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial is to be provided R= right Angle Gear Reducer 5 = 5 to 1 Gear Ratio L1 = Left End Shaft Location, Position 1 (36LBS) |
1980-112-X-SP-X-S-4-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-112-X-SP-X-S-4-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 12 = 12 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 4 = 4 to 1 Gear Ratio R = Right End Shaft Location |
1980-116-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-116-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 16 = 16 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (30LBS) |
1980-118-L-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-118-L-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 018 = 18 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty |
1980-118-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-118-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 018 = 18 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty |
1980-118-X-SP-TD1-S-1.5-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-118-X-SP-TD1-S-1.5-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 018 = 18 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation S = Straight Drive Gear Reducer 1.5 = 1 & 1/2 to 1 Gear Ratio L = Gear Reducer & Shaft Extension on Left End |
1980-118-X-SP-TD1-S-1.5-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-118-X-SP-TD1-S-1.5-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 018 = 18 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation S = Straight Drive Gear Reducer 1.5 = 1 & 1/2 to 1 Gear Ratio R = Gear Reducer & Shaft Extension on Right End |
1980-1202-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1202-R-SP-TD1 Series 1980 12 = NEMA 12 Enclosure 02 = 2 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD1 = Timing Dial C.W. Clock Wise Rotation |
1980-1203-R-SP-R-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1203-R-SP-R-TD1 Series 1980 12 = NEMA 12 Enclosure 03= 3 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw Snap Action Switches R = Rubber Boot on Switch Plunger TD1 = Timing Dial Clock Wise Rotation |
1980-1203-R-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1203-R-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Enclosure 03 = Qty. 3, Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch R = Rubber Boot / Seal on the Switch Plunger for additional moisture protection X = No Timing Dial or Dial Window is to be provided 3 Year Warranty |
1980-1203-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1203-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Enclosure 03 = Qty. 3, Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty |
1980-1204 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204 Series 1980 12 = NEMA 12 Enclosure 4 = 4 Cams / Circuits / Switches = Left Hand Shaft Extension from enclosure = DPDT Switches / Double Pole Double Throw X = No Timing Dial or Dial Window is provided |
1980-1204-D-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-D-DP-X Series 1980 12 = NEMA 12 Enclosure 4 = 4 Cams / Circuits / Switches D = Double Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw X = No Timing Dial or Dial Window is provided |
1980-1204-D-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-D-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure D = Dual (2) Shaft Extensions from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial C.W. Clock Wise Rotation 3 Year Warranty |
1980-1204-D-SPG-R-X |
Ametek Gemco Rotating Cam Limit Switch Model Like 1980-1204-D-SPG-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Dual Shaft Extensions from Enclosure, 2 SPG = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch, with Gold Plated Contacts Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boots on the Switch Plunger for additional protection from Moisture & Dust X = No Timing Dial or Dial Window is to be provided (19LBS) 1/8 |
1980-1204-D-SPP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-D-SPP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Double Shaft Extension from enclosure. Right & Left Side SPP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch with Plug in Sockets Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (18LBS) |
1980-1204-L-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-L-DP-X Series 1980 12 = NEMA 12 Enclosure 4 = 4 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw X = No Timing Dial or Dial Window is provided |
1980-1204-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (19LBS) |
1980-1204-R-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-R-DP-X Series 1980 12 = NEMA 12 Enclosure 4 = 4 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw X = No Timing Dial or Dial Window is provided |
1980-1204-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure, Dust Tight 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty |
1980-1204-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (19LBS) |
1980-1204-X-DP-X-S-80-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-DP-X-S-80-R Series 1980 12 = NEMA 12 Enclosure 4 = 4 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches, Double Pole Double Throw X = No Timing Dial S = Straight Drive Gear Reducer 80 = 80 to 1 Gear Ratio R = Right End Shaft Location (24LBS) |
1980-1204-X-SP-R-72-L1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-R-72-L1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension opposite gear box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided R = Right Angle Drive Gear Reducer 72 = 18 to 1 Gear Ratio L1 = Shaft Location |
1980-1204-X-SP-X-R-6-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-R-6-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure, Watertight 04 = 4 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial R = Right Angle Drive Gear Reducer 6 = 6 to 1 Gear Ratio R1 = Shaft Location, Right End, Shaft Position 1 |
1980-1204-X-SP-X-R-8-R3 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-R-8-R3 Series 1980 12 = NEMA 12 Enclosure 04 = 4 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw X = No Timing Dial R = Right Angle Drive Gear Reducer 8 = 8 to 1 Gear Ratio R3 = Shaft Location |
1980-1204-X-SP-X-S-2.2-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-S-2.2-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 2.2 = 2.2 to 1 Gear Ratio L = Left End Shaft Location |
1980-1204-X-SP-X-S-8-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-S-8-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 8 = 8 to 1 Gear Ratio L = Left End Shaft Location |
1980-1204-X-SP-X-S-8-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-S-8-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 8 = 8 to 1 Gear Ratio R = Right End Shaft Location |
1980-1205-D-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-D-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches D = Double Shaft Extension from enclosure, 2 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD1 = Timing Dial Labeled for Clockwise Rotation, 0-360 Degrees 3 Year Limited Warranty (22LBS) |
1980-1205-L-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-L-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from enclosure, 2 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (24LBS) |
1980-1205-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-L-SP-X Series 1980 12 = NEMA 12 Enclosure 5 = 5 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw X = No Timing Dial or Dial Window is provided |
1980-1205-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 05 = 5 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from enclosure, 2 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (24LBS) |
1980-1205-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 05 = 5 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from enclosure, 2 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial 3 Year Limited Warranty (22LBS) |
1980-1205-X-DP-S-6-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-X-DP-X-S-6-R Series 1980 12 = NEMA 12 Enclosure 05 = 5 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches, Double Pole Double Throw X = No Timing Dial S = Straight Drive Gear Reducer 6 = 6 to 1 Gear Ratio R = Right End Shaft Location
|
1980-1206-D-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-D-DP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 6 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Dual Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (16LBS) |
1980-1206-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 6 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (24LBS) |
1980-1206-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 6 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (24LBS) |
1980-1206-X-DP-R-X-S-14-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-R-X-S-14-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boots on the switch plunger for additional moisture & dust protection X = No Timing Dial S = Straight Drive Gear Reducer 14 = 14 to 1 Gear Ratio R = Right Side, Gear Box & Main Shaft |
1980-1206-X-DP-X-R-18-L1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-X-R18-L1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial R = Right Angle Drive Gear Reducer 18 = 18 to 1 Gear Ratio L1 = Shaft Location |
1980-1206-X-DP-X-S-1.33-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-X-S-1.33-L Series 1980 12 = NEMA 12 Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches, Double Pole Double Throw X = No Timing Dial S = Straight Drive Gear Reducer 1.33 = 1.33 to 1 Gear Ratio L = Left End Shaft Location |
1980-1206-X-DP-X-S-1.33-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-X-S-1.33-R Series 1980 12 = NEMA 12 Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches, Double Pole Double Throw X = No Timing Dial S = Straight Drive Gear Reducer 1.33 = 1.33 to 1 Gear Ratio R = Right End Shaft Location |
1980-1206-X-DP-X-S36-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-X-S-36-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 06 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 36 = 36 to 1 Gear Ratio L = Left End Shaft Location |
1980-1206-X-SP-R-X-S-16-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-R-X-S-16-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gear box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot on the switch plunger for additional moisture protection X = No Timing Dial or Dial Window is to be provided S= Straight Drive Gear Reducer 16 = 16 to 1 Gear Ratio L = Left End Gear Reducer (28LBS) |
1980-1206-X-SP-TD1-S-25-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-TD1-S-25-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD1 = Timing Dial labeled for clock wise rotation S = Straight Drive Gear Reducer 25 = 25 to 1 Gear Ratio R = Right End Shaft Location |
1980-1206-X-SP-X-S-15-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-S-15-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial S = Straight Drive Gear Reducer 15 = 15 to 1 Gear Ratio R = Right End Shaft Location (26LBS) |
1980-1206-X-SP-X-S-30-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-X-S-30-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 30 = 30 to 1 Gear Ratio R = Right End Shaft Location (26LBS) |
1980-1206-X-SP-X-S-8-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-X-S-8-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 8 = 8 to 1 Gear Ratio R = Right End Shaft Location |
1980-1207-D-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1207-D-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Enclosure 07 = 7 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure D = Dual (2) Shaft Extensions from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial C.W. Clock Wise Rotation 3 Year Warranty |
1980-1208-D-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-D-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Enclosure 08 = 8 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure D = Dual (2) Shaft Extensions from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial labeled for Clock Wise Rotation 3 Year Warranty |
1980-1208-D-SP-TD3 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-D-SP-TD3 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Enclosure 08 = 8 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure D = Dual (2) Shaft Extensions from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD3 = Timing Dial labeled for Clock Wise Rotation with the main shaft vertical 3 Year Warranty (32LBS) |
1980-1208-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 08 = 8 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (26LBS) |
1980-1208-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 08 = 8 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (26LBS) |
1980-1208-X-SP-TD1-S-14-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-X-SP-TD1-S-14-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Enclosure 08 = 08 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for Clockwise Rotation S = Straight Drive Gear Reducer 14 = 14 to 1 Gear Ratio L = Left End Shaft Location (37LBS) |
1980-1208-X-SP-X-R-18-L7 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-X-SP-X-R-18-L7 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 08 = 8 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox / no double shaft extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided R= Right Angle Gear Reducer 18 = 18 to 1 Gear Ratio L7 = Left End Gear Reducer Shaft Location 7 (28LBS) |
1980-1208-X-SP-X-R-25-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-X-SP-X-R-25-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 08 = 8 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial is to be provided R = Right Angle Drive Gear Reducer 25 = 25 to 1 Gear Ratio R1 = Shaft Location |
1980-1208-X-SP-X-S-30-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-S-30-L Series 1980 12 = NEMA 12 Enclosure 08 = 08 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw Snap Action X = No Timing Dial S = Straight Drive Gear Reducer 30 = 30 to 1 Gear Ratio L = Left End Shaft Location (28LBS) |
1980-1209-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1209-L-SP-X Series 1980 12 = NEMA 12 Enclosure 9 = 9 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw X = No Timing Dial or Dial Window is provided |
1980-1210-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1210-R-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 10 = 10 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty |
1980-1210-X-SP-R-X-R-7.5-L1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1210-X-SP-R-X-R-7.5-L1 Series 1980 12 = NEMA 12 Enclosure 10 = 10 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw Snap Switch U.L. Listed R = Rubber Boot on Snap Switch Plunger X = No Timing Dial R = Right Angle Gear Reducer 7.5 = 7.5 to 1 Gear Ratio L1 = Right End Shaft Location, Position 1 (34LBS) |
1980-1211-L-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1215-L-SP-TD1 Series 1980 12 = NEMA 12 Enclosure 15 = 15 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD1 = Timing Dial C.W. Clock Wise Rotation |
1980-1212-D-SP-TD3 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1212-D-SP-TD3 Series 1980 12 = NEMA 12 Enclosure 12 = 12 Cams / Circuits / Switches D = Double Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD3 = Timing Dial, Clock Wiser Rotation, Vertical Mounting |
1980-1212-D-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1212-D-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 12 = 12 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Dual Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (21LBS) |
1980-1212-X-DP-X-R-5-R3 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1212-X-DP-X-R-5-R3 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 12 = 12 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial R= Right Angle Precision Gear Reducer 5 = 5 to 1 Gear Ratio R3 = Right End Gear Reducer Shaft Location 3 |
1980-1212-X-DP-X-R-6-L7 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1212-X-DP-X-R-6-L7 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 12 = 12 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial R = Right Angle Gear Reducer 6 = 6 to 1 Gear Ratio R = Right End Shaft Location |
1980-1215-L-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1215-L-SP-TD1 Series 1980 12 = NEMA 12 Enclosure 15 = 15 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD1 = Timing Dial C.W. Clock Wise Rotation |
1980-1216-R-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1216-R-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 16 = 16 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional dust & moisture protection X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (50LBS) |
1980-1346 |
Ametek Gemco Rotating Cam Limit Switch like Model 1980-104-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided Special Engineered Product, 3 Cams with a provision for a 4th cam installed by the OEM. A switch is installed but the OEM provided their own or left out the cam in the spare area for future use 3 Year Limited Warranty (12LBS) |
1980-1535 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-1535 like a 1980-102-L-SP-X with a special main shaft Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 02 = 2 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided Specially Engineered Main Shaft Extension: 1/2 Inch Dia X 2 & 5/8 Inches Long Perkins Press (10LBS) |
1980-1669 |
Ametek Gemco Deck Type Limit Switch. 3 Decks. 1950-1-B-A-AO |
1980-1780 |
Ametek Gemco 1980-104-L-SP-X & a 1970-104 Drive-Chek |
1980-1928 |
Ametek Gemco Rotating Cam Limit Switch Like Model 1980-104-L-SP-X Series 1980 1 = NEMA 1 Enclosure 4 = 4 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw X = No Timing Dial or Dial Window is provided Special OEM Product provided to Midland Ross in 1975 Has a special 2 & 7/16 Inch Main Shaft Extension from the Cam Box with the Shaft End Tapped for a 1/4 - 20 fastener (12LBS)
|
1980-2090 |
Ametek Gemco Rotary Cam Limit Switch. 4 circuit, NEMA 12 Enclosure, Left Hand Shaft Extension, Qty. 3, S.P.D.T. & Qty. 1, D.P.D.T. Switches. |
1980-2152 |
Ametek Gemco DUAL SHAFT Rotating Cam Limit Switch with Qty. 2, parallel shafts each having Qty. 3, circuits / cams / switches. Precision snap Acting D.P.D.T. Switches. Total 6 circuits. The 2 parallel shafts are coupled with a chain & sprocket inside the enclosure. A Gemco 3001-3 Adjustable Coupling is used to allow timing changes between the 2 shafts. Right hand shaft extension in position ''D'' with a second Gemco 3001-3 Adjustable Coupling. NEMA 4 Metal Enclosure. Originally designed for Kaiser Steel in 1977 |
1980-2179 |
Ametek Gemco Rotating Cam Limit Switch Like a 1980-103-L-SP-X with 2 Special Cams Cam #1 = SD0189100 (Min. Dwell) cir #1 location LH side Cam #2 = SD0164600 (Min. Lobe) cir #2 location Cam #3 = SD0117800 (Standard) cir #3 location Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) |
1980-2312 |
Ametek Gemco Specially Engineered Rotating Cam Limit Switch Series 1980 Cam Box featuring some of the cams with Adjustable Timing & Dwell NEMA 1 Rated Enclosure, Specially Engineered Enclosure & Cover 18 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from Enclosure Qty 16, SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Qty 2, DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch 13 Standard Cams, SD0117800 2 Special 15 Degree Cams, SD0203000 1 Special 75 Degree Cam, SD0203100 2 Special 40 Degree Cams, 1/2 Circuit, Right Hand, SD0207500 Internal Right Angle Gear Reducer with a having a 6:1 ratio 3 Position Selector Switch, 22mm with a Black Lever, Spring Return 9/6 |
1980-2366 |
Ametek Gemco Rotating Cam Limit Switch. 7 circuits / Cams / Switches. Single Pole Double Throw Switches. Dual Output Shafts. External Timing Dial with Pulse Disk and Switch. Includes # 3001-1 1/2 Inch Sprocket Drive Coupling. |
1980-23875A |
Ametek Gemco Rotating Cam Limit Switch. Specially engineered product |
1980-2441 |
Ametek Gemco Series 1980 Rotating Cam Limit Switch. 11 circuit cam box with 5 standard cams and 6 special cut cams with 20 degree lobes. SPDT switches with boots. Includes a right angle gear reducer with a 10 to 1 ratio mounted on the left end with a straight shaft in position L1 . NEMA 12 enclosures. |
1980-2527 |
Ametek Gemco 1980 Series Cam Box OEM Link Systems NEMA 1 Enclosure 2 Independent Circuits / Cam / Switches ''Add a Cam'' feature which allows enclosure space for the OEM or End User to add 2 cams at a latter date Right Hand Shaft Extension Tach Generator Module Precision Snap Acting Single Pole Double Trow Switches S.P.D.T. Roller Followers were included
|
1980-2529 |
Ametek Gemco / Link Rotating Cam Limit Switch Model 1980-2529 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 4 = 4 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch With Encoder, Brevel Motors, 902436 Link Electric only |
1980-2761 |
Ametek Gemco Rotating Cam Limit Switch Like Switch Model 1980-911-X-SP-TD1-S-12-L Series 1980 9 = NEMA 9 Group F Enclosure 11 = 11 Independent Cams / Circuits / Switches X = No Shaft opposite gearbox SP = SPDT Switches / Single Pole Double Throw Snap Action Switches U.L. Listed TD1 = Timing Dial Labeled for C.W. Rotation S = Straight Drive Gear Box 12 = 12 to 1 Gear Ratio L = Gear Box Mounted to Left End With Strip Heater & Thermostat (50LBS) |
1980-3004B |
Ametek Gemco Cam Limit Switch 4 Circuit with SPDT Switches NEMA 1 with Custom Enclosure & Main Shaft Detail Left Hand Shaft Extension With the ''ADD A CAM'' feature for future or OEM addition of Cam / Circuit |
1980-3010T |
Ametek Gemco Rotating Cam Limit Switch Model 1980-3010T, replaced 1980-3010 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand Left Hand Shaft Extension from Enclosure Qty 3, SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Qty 1, DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch Add on Tach Gen Module PSD153603 Includes Drive Chek 1970-104 & 2 Special Cams SD2231 110 Degrees & Cam SD2382 45 Degrees on the DPDT Switch 4 weeks 6/7 |
1980-3087 |
Ametek Gemco 1980 Series Cam Box with Motion Detect. NEMA 1 Enclosure 5 Circuit / Switch / Cam with Motion Detect |
1980-3145 |
Ametek Gemco Special Rotating Cam Limit Switch. NEMA 1 Enclosure, 4 Cams / Circuits, Left Hand Shaft Extension, S.P.D.T. = Single Pole Double Throw Switches, 3 Standard Cams with a provision for a 4th cam installed by the OEM Bliss Salem. The switch is installed but we have no record of what type of cam Bliss Salem installed if any in the spare area. 2 weeks to ship. |
1980-3146 |
Ametek Gemco Rotating Cam Limit Switch Model like model 1980-106-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Enclosure 06 = 5 Cams / Circuits / Switches, with the add a cam feature for a future circuit L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (14LBS) 4/7 |
1980-3157 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-3157 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided SD0197700 Optical Disc SD0194800 Motion Detect Switch in Circuit 6 (29LBS) 7/6 |
1980-3315 |
Gemco 1980 Series Cam Box Specially engineered product 4 Circuit NEMA 4X, 304 Stainless Steel Enclosure 1 to 3 Straight Drive Gear Multiplier, Internally Mounted SPDT Switches with the Rubber Boot option Enclosure is heated with a Thermostat Controlled Strip Heater Double Shaft Extensions from enclosure 2001403 8/7 |
1980-3327 |
Ametek Gemco Rotating Cam Limit Switch Model Like model 1980-1210-X-SP-X-R-10-R1 Series 1980 12 = NEMA 12 Enclosure 10 = 10 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw Snap Switch U.L. Listed X = No Timing Dial R = Right Angle Gear Reducer 10 = 10 to 1 Gear Ratio R1 = Right End Shaft Location, Position 1 Special 6 Inch Diameter Cams normally used with the Series 1997 Gate Hoist Products Line A larger enclosure is also supplied to enclose these cams 8/6 (45LBS) |
1980-3383 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-3383 Series 1980 1 = NEMA 1 Enclosure 10 = 10 Cams / Circuits / Switches 2 of these cams do not have adjustable dwell. They are machined with 25 degrees of dwell Right Hand Shaft extension from enclosure 9 Single Pole Double Throw Switches 1 1950-1406 Slow Make - Slow Break Switch X = No Timing Dial or Dial Window is provided |
1980-3426 |
Ametek Gemco 1980 Series Cam Limit Switch Engineered Part Number 6 Circuit / Cams NEMA 4 Rated Enclosure, Watertight SPDT UL Rated Snap Switches Right Hand Unit Gear Multiplier, 4 to 1 Ratio Includes an Ametek Gemco 1/2 Inch Direct Drive Coupling. Maximum torque rating 300 lb.-in. 1/2 inch direct & sprocket drive 404 woodruff keyway & key. 50 turns of the adjusting screw will rotate coupling 360 degrees. For easily made incremental adjustment between drive shaft & cam box |
1980-3434 |
Ametek Gemco 1980 Series Cam Box NEMA 12 Enclosure 6 Circuits / Cams / Switches Double Ended Shaft Extension Pulse Generating Disc Built in 1983 for International Harvester |
1980-3486 |
Ametek Gemco Cam Box Series 1980 1980-3486 6 Independent Circuit / Cam / Switch S.P.D.T. Switches, Single Pole Double Throw Precision Snap Acting Switches NEMA 1 Enclosure Left Hand Shaft Extension Add On feature for Tach Gen Tach Generator (supplied buy others) Lock Out Feature (accepts padlock)
|
1980-3503 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-3503 Series 1980 NEMA 9 Enclosure with strip heater & thermostat 11 Cams / Circuits / Switches Timing Dial is included Straight Drive Gear Reducer 10 to 1 Ratio 4 to 6 weeks to ship. |
1980-3510 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-3510 Similar to 1980-1204-L-SP-X Series 1980 12 = NEMA 12 Enclosure 04 = 4 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure Specially machined cams 2 @ 15 Degrees Dwell & 2 @ 60 Degrees Dwell Special 1950-1413 Switches. SPDT Slow Make - Slow Break, can be wired for Normally Open or Normally Closed Circuits. 8 screw terminals. The 1950-1413 previously supplied switch is no longer available. It was a SPST switch with a normally closed contact only X = No Timing Dial or Dial Window is provided 5/6 |
1980-3742 |
Ametek Gemco Rotating Cam Limit Series 1980 NEMA 9 Enclosure 11 Cams / Circuits / Switches Double Pole Double Throw Switches Straight Drive Gear Reducer 12 to 1 Gear Ratio With Timing Dial, Strip Heater & Thermostat |
1980-3809 |
Ametek Gemco Cam Limit Switch Engineered Part Number Like 1980-409-R-SP-X with Tach Gen., Spring Return & Clutch |
1980-3875A |
Ametek Gemco Rotating Cam Limit Switch. Specially engineered product |
1980-3989 |
Ametek Gemco Rotating Cam Limit Switch 1 = NEMA 1 Rated Enclosure 08 = 8 Independent Cams / Circuits / Switches X = No shaft extension opposite gearbox / no double shaft extension Engineered product with both Single & Double Throw Switches X = No Timing Dial or Dial Window is to be provided R= Right Angle Gear Reducer 40 = 40 to 1 Gear Ratio R1 = Right End Gear Reducer Position 1 |
1980-3990 |
Ametek Gemco Rotating Cam Limit Switch Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 08 = 8 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox / no double shaft extension Engineered product with both Single & Double Throw Switches, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided R= Right Angle Gear Reducer 20= 20 to 1 Gear Ratio L1 = Left End Gear Reducer Shaft Location 1 |
1980-401-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-401-R-SP-X Series 1980 4 = NEMA 4 Water Resistant Enclosure 01 = 1 Cams / Circuit / Switch R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw Snap Action Switch U.L. Listed X = No Timing Dial or Dial Window is provided 3 Year Warranty (19LBS) |
1980-402-D-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-402-D-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 02 = 2 Independent Cams / Circuits / Switches D = Double Shaft Extension from enclosure, 2 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (18LBS) |
1980-402-X-DP-X-R-10-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-402-X-DP-X-R-10-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 02 = 2 Independent Cams / Circuits / Switches. The micro-adjust cams maintain accuracy / repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand. The cams have a switch setting range of 4 through 356 Degrees X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch.Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial R= Right Angle Gear Reducer 10 = 10 to 1 Gear Ratio R1 = Right End Gear Reducer Shaft Location 1 |
1980-403-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-403-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (20BS) |
1980-403-X-DP-X-S-200-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-403-X-DP-X-S-200-L Series 1980 4 = NEMA 4 Enclosure 3 = 3 Cams / Circuits / Switches X = No shaft extension opposite gear box DP = DPDT Switches / Double Pole Double Throw X = No Timing Dial or Dial Window is provided S = Straight Drive Gear Reducer 200 = 200 to 1 Gear Ratio L = Left End Shaft Location 26 LBS Gross |
1980-404 X-SP-R-X-S-60-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-R-X-S-60-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox / no double shaft extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = R = Rubber boot on Switch Plunger for additional moisture protection X = No Timing Dial or Dial Window is to be provided S= Straight Drive Gear Reducer. Shaft parallel to main shaft 60 = 60 to 1 Gear Ratio R = Right End Gear Reducer Location (26LBS) |
1980-404-D-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-D-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell04 = NEMA 4 Rated Enclosure 04 = 4 Cams / Circuits / Switches D = Double / 2 Shaft Extensions from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch R = Rubber Boot on Switch Plunger for addition moisture & contaminant protection X = No Timing Dial or Dial Window is provided 3 Year Limited Warranty (19LBS) |
1980-404-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 4 = 4 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is provided 3 Year Warranty (18LBS) |
1980-404-R-DP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-R-DP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 4 = 4 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is provided 3 Year Warranty (18LBS) |
1980-404-R-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-R-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell04 = NEMA 4 Rated Enclosure 4 = 4 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch R = Rubber Boot on Switch Plunger for addition moisture & contaminant protection X = No Timing Dial or Dial Window is provided (21LBS) |
1980-404-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 4 = 4 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is provided 3 Year Warranty (20LBS) |
1980-404-X-SP-R-X-S-28L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-R-X-S-28-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided S = Straight Drive Gear Reducer 28 = 28 to 1 Gear Ratio L = Left End Gear Reducer (24LBS) |
1980-404-X-SP-R-X-S-60-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-R-X-S-60-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No shaft extension opposite gearbox SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided S = Straight Drive Gear Reducer 60 = 60 to 1 Gear Ratio R = Right End Gear Reducer (24LBS) |
1980-404-X-SP-X-R-15-R2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-X-R-15-R2 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial is to be provided R = Right Angle Gear Reducer 15 = 15 to 1 Gear Ratio R = Right End Shaft Location 2 = Shaft Location Position 2 |
1980-404-X-SP-X-R-60-R2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-X-R-60-R2 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial is to be provided R = Right Angle Gear Reducer 60 = 60 to 1 Gear Ratio R = Right End Shaft Location 2 = Shaft Location Position 2 |
1980-404-X-SP-X-S-100-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-X-S-100-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided S = Straight Drive Gear Reducer 100 = 100 to 1 Gear Ratio L = Left End Shaft Location (29LBS) |
1980-404-X-SP-X-S-35-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-X-S-35-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 04 = 4 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 35 = 35 to 1 Gear Ratio R = Right End Shaft Location |
1980-405-D-DP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-405-D-DP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure, Watertight 05 = 5 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Double Shaft Extension from Enclosure, shaft out both ends DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty |
1980-405-D-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-405-D-SP-X Series 1980 4 = NEMA 4 Enclosure 5 = 5 Cams / Circuits / Switches D = Double Shaft Extension SP = SPDT Switches / Single Pole Double Throw X = No Timing Dial or Dial Window is provided |
1980-405-R-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-405-R-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure, Watertight 05 = 5 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (22LBS) |
1980-405-R-SPP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-405-R-SPP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Watertight Enclosure 05 = 5 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SPP = SPDT Switches / Single Pole Double Throw with the Optional Plug-In Socket. Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot option on Switch Plunger for additional moisture protection X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (22LBS) |
1980-405-X-DP-X-S-200-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-405-X-DP-X-S-200-L Series 1980 4 = NEMA 4 Enclosure 5 = 5 Cams / Circuits / Switches X = No shaft extension opposite gear box DP = DPDT Switches / Double Pole Double Throw X = No Timing Dial or Dial Window is provided S = Straight Drive Gear Reducer 200 = 200 to 1 Gear Ratio L = Left End Shaft Location (30LBS) |
1980-406-D-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-D-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure, Watertight 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Dual Shafts Extending from Enclosure,Two SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (36LBS) |
1980-406-L-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-L-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (27LBS) |
1980-406-R-3DP/3SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-3DP/3SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure 3DP = Qty 3 DP Switches 3SP = Qty 3 SP Switches TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty |
1980-406-R-DP-X-S-2-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-DP-X-S-2-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 2 = 2 to 1 Gear Ratio L = Left End Gear Reducer / Shaft Location |
1980-406-R-SP-R-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot on switch plunger for moisture & dust protection TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (36LBS) |
1980-406-R-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot option on switch plunger for additional protection from moisture & dust X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (24LBS) |
1980-406-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty (27LBS) |
1980-406-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (24LBS) |
1980-406-X-DP-X-M-3-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-DP-X-M-3-R Series 1980 Vertex S827-6800-30 4 = NEMA 4 Enclosure 06 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches, Double Pole Double Throw Snap Action Switches U.L. Listed X = No Timing Dial M= Multiplier Drive 3 = 1 to 3 Multiplier Ratio R = Right End Shaft Location 1980-4478 |
1980-406-X-DP-X-S-2-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-DP-X-S-2-L Series 1980 4 = NEMA 4 Enclosure 6 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite Gear Box DP = D.P.D.T. Switches, Double Pole Double Throw, Snap Acting X = No Timing Dial S= Straight drive Gear Reducer 2 = 2 to 1 Gear Ratio L = Left End Shaft Location |
1980-406-X-SP-R-X-S-20-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-R-X-S-20-R Series 1980 4 = NEMA 4 Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches R = Rubber Boot Option X = No Timing Dial S = Straight Gear Reducer 20 = 20 to 1 Gear Ratio R = Right Shaft Location |
1980-406-X-SP-TD4-R-15-L8 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-TD4-R-15-L8 Series 1980 4 = NEMA 4 Enclosure 6 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw TD4 = Timing Dial 0 - 360 Vertical Labeling for Counter Clock Wise Rotation R = Right Angle Gear Reducer 15 = 15 to 1 Gear Ratio L = Left End Shaft Location 8 = Shaft Location Position 8 3 Year Warranty |
1980-406-X-SP-X-R-15-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-X-R-15-R1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial is to be provided R = Right Angle Gear Reducer 15 = 15 to 1 Gear Ratio R = Right End Shaft Location 1 = Shaft Location Position 1 |
1980-406-X-SP-X-R-96-L-4 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-X-R-96-L4 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial is to be provided R = Right Angle Gear Reducer 96 = 96 to 1 Gear Ratio L = Left End Shaft Location 1 = Shaft Location Position 4 (34LBS) |
1980-406-X-SP-X-S-14-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-X-S-14-R Series 1980 30 LBS Gross 4 = NEMA 4 Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw X = No Timing Dial S= Straight Drive Gear Reducer 14 = 14 to 1 Gear Ratio R = Right End Shaft Location |
1980-406-Y-SP-TD1-S-15-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-Y-SP-TD1-S-15-L Series 1980 4 = NEMA 4 Enclosure 6 = 6 Independent Cams / Circuits / Switches Y = Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw TD1 = Timing Dial 0 - 360 Clock Wise S = Straight Drive Gear Reducer 15 = 15 to 1 Gear Ratio L = Left End Shaft Location 3 Year Warranty (35LBS) |
1980-406-Y-SP-X-S-8-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-Y-SP-X-S-8-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches Y = Shaft Extension Opposite the Gear Box / Double Shaft Extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 8 = 8 to 1 Gear Ratio R = Right End Shaft Location |
1980-407-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-407-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 07 = 7 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty |
1980-407-X-SP-R-X-S- |
Ametek Gemco Rotating Cam Limit Switch Model 1980-407-X-SP-R-S-100-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 07 = 7 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot option on Switch Plunger for additional moisture protection X = No Timing Dial is to be provided S = Straight Drive Gear Reducer 100 = 100 to 1 Gear Ratio L = Left End Gear Reducer / Main Shaft |
1980-407-X-SP-R-X-S-32R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-407-X-SP-R-S-32-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 07 = 7 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot option on Switch Plunger for additional moisture protection TD2 = Timing Dial Labeled for Reverse Rotation S = Straight Drive Gear Reducer 32 = 32 to 1 Gear Ratio R = Right End Gear Reducer / Main Shaft |
1980-408-L-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-408-L-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Watertight Enclosure 08 = 8 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch R = Rubber Boot option on switch plunger X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (32LBS) |
1980-408-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-408-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Watertight Enclosure 08 = 8 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (32LBS) |
1980-408-R-DP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-408-R-DP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Watertight Enclosure 08 = 8 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Warranty (32LBS) |
1980-408-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-408-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Watertight Enclosure 08 = 8 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Warranty (32LBS) |
1980-408-X-DP-TD1-R-1-L1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-408-X-DP-TD1-R-1-L1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Watertight Enclosure 08 = 8 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite Gear Box DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch TD1 = Timing Dial Labeled for C.W. Rotation R = Right Angle Gear Reducer L1 = Shaft Location from Gear Box |
1980-408-X-SP-TD1-X-M-3-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-408-X-SP-TD1-M-3-R Series 1980 4 = NEMA 4 Enclosure 08 = 8 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw TD1 = Timing Dial Clock Wise Rotation M= Multiplier Drive 3 = 1 to 3 Multiplier Ratio R = Right End Shaft Location |
1980-408-Y-SP-X-M-4-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-408-Y-SP-X-M-4-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 08 = 8 Independent Cams / Circuits / Switches Y = Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial M= Multiplier Drive 4 = 1 to 4 Multiplier Ratio L = Left End Shaft Location (36LBS) |
1980-409-R-4DP/5SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-409-R-4DP/5SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 09 = 9 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure 4DP = Qty 4 DP Switches 5SP = Qty 5 SP Switches TD1 = Timing Dial Labeled for C.W. Rotation 3 Year Limited Warranty |
1980-410-D-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-410-D-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 10 = 10 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Double Shaft Extension from both sides Enclosure 2 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty |
1980-410-R-SP-R-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-410-R-SP-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 10 = 10 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty |
1980-410-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch Model 1980-410-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 10 = 10 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty |
1980-410-X-SP-TD1-S-80-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-410-X-SP-TD1-S-80-R Series 1980 4 = NEMA 4 Enclosure 10 = 10 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw TD1 = Timing Dial, Clockwise Rotation S = Straight Drive Gear Reducer 80 = 80 to 1 Gear Ratio R = Right End Shaft Location |
1980-410-X-SP-TD2-S-35-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-410-X-SP-TD2-S-35-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 10 = 10 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD2 = Timing Dial Labeled for Counter Clock Wise Rotation S= Straight Drive Gear Reducer 35= 35 to 1 Gear Ratio L = Left End Shaft Location (24LBS) |
1980-410-X-SP-X-S-100-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-410-X-SP-X-S-100-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 10 = 10 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided S = Straight Drive Gear Reducer 100 = 100 to 1 Gear Ratio R = Right End Shaft Location |
1980-411-R-SP-TD2 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-411-R-SP-TD2 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 11= 11 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch TD2 = Timing Dial Labeled for C.C.W. Counter Clock Wise Rotation but without timing dial window on the enclosure 3 Year Warranty (36LBS) |
1980-411-X-SP-X-M-4-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-411-X-SP-X-M-4-R Series 1980 4 = NEMA 4 Enclosure 11= 11 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw X = No Timing Dial M = Multiplier Drive 4 = 4 to 1 Gear Multiplier R = Right End Shaft Location (43LBS) |
1980-411-X-SP-X-S-4-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-411-X-SP-X-S-4-R Series 1980 4 = NEMA 4 Enclosure 11= 11 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw X = No Timing Dial S = Straight Drive Gear Reducer 4 = 4 to 1 Gear Ratio R = Right End Shaft Location |
1980-412-X-SP-X-S-100-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-412-X-SP-X-S-100-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 12= 12 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 100 = 100 to 1 Gear Ratio R = Right End Shaft Location 41 LBS |
1980-412-X-SP-X-S-36-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-412-X-SP-X-S-36-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Watertight Enclosure 12 = 12 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 36 = 36 to 1 Gear Ratio L = Left End Shaft Location |
1980-412-X-SP-X-S10-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-412-X-SP-X-S-10-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure, Watertight 12 = 12 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 10 = 10 to 1 Gear Ratio L = Left End Shaft Location |
1980-412-Y-SP-X-M-6-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-412-Y-SP-X-M-6-R Series 1980 4 = NEMA 4 Enclosure 12 = 12 Cams / Circuits / Switches Y = Shaft Extension oposite gearbox. (double) SP = SPDT Switches. Single Pole Double Throw X = No Timing Dial M = Mutiplier Drive 6 = 1 to 6 Gear Multiplier Ratio R = Gear Multiplier, Right End Loc |
1980-412-Y-SP-X-S-200-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-412-Y-SP-X-S-200-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 12 = 12 Independent Cams / Circuits / Switches Y = Shaft Extension Opposite the Gear Box / Double Shaft Extension SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 200 = 200 to 1 Gear Ratio L = Left End Gear Box & Shaft Location |
1980-414-R-SP-R-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 980-414-R-SP-R-TD1 Series 1980 4 = NEMA 4 Rated Enclosure 14 = 14 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw R = Rubber Boot on Switch Plunger TD1 = Timing Dial C.W. Clock Wise Rotation R = Right Hand Shaft Extension |
1980-415-X-SP-TD1-S-12-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-415-X-SP-TD1-S-12-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 15 = 15 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation S = Straight Drive Gear Reducer, shaft parallel with main shaft 12 = 12 to 1 Gear Ratio, every 12 turns of the main shaft the cams turn once R = Right End Shaft Location |
1980-416-L-SP-TD1-R-100-R1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-416-L-SP-TD1-R-100-R1 Series 1980 4 = NEMA 4 Enclosure 16 = 16 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD1 = Timing Dial C.W. Clock Wise Rotation R = Right Angle Gear Reducer 100 = 100 to 1 Gear Reducer Ratio R-1 = Shaft Location on Gear Reducer |
1980-416-L-SP-TW1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-416-L-SP-TW1 Series 1980 4 = NEMA 4 Enclosure 16 = 16 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TW1 = Timing Dial C.W. Clock Wise Rotation with a Timing Dial Window on the Enclosure |
1980-416-L-SP-X |
Ametek Gemco Cam Limit Switch Switch Settings 4 to 356 Degrees without a Tool - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 Series 1980 Micro-Adjust Rotating Cam Limit Switch Model 1980-416-R-SP-X 4 = NEMA 4 Enclosure 16 = Qty. 16, Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw with one NO and one NC contact per switch rated at 15 million cycles X = No Timing Dial or dial window is to be provided Warranty 3 years With NEMA 4X Stainless Adder & 2.5 Inch Shaft Extension without woodruff key and keyslot 10% expedite fee for shipment within 2.5 week. Expedite fee will be dropped if factory does not ship in 2.5 weeks |
1980-4160 |
Ametek Gemco Cam Box like 1980R-406-X-DP-X-R-3-L with 304 Stainless Steel Option. NEMA 4X, 6 Circuits, 3 to 1 Ratio, Includes Resolver EC70289 # SD0308910. Enclosure size is to be the same as original units. Bascular Span Drawbridge Long Island NY. 1980-4160 RAGR/SS EN |
1980-4161 |
Ametek Gemco Cam Box like1980R-406-X-DP-X-R-3-R with 304 Stainless Steel Option. NEMA 4X, 6 Circuits, 3 to 1 Ratio, Includes Resolver EC70289 # SD0308910. Enclosure size is to be the same as original units. Bascular Span Drawbridge Long Island NY. 1980-4161 RAGR/SS EN |
1980-4223 |
Ametek Gemco Rotating Cam Limit Specially Engineered Product Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell NEMA 4 Rated Watertight Enclosure 8 Independent Cams / Circuits / Switches Left Hand Shaft Extension from enclosure SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Timing Dial Labeled for Counter Clock Wise Rotation Multiplier Gear Drive with a Ratio of 1 to 4 Encoder Provision, for a customer supplied encoder (40LBS) 7/7 |
1980-4245 |
Ametek Gemco Rotating Cam Limit Switch Model Series 1980 Cam Box featuring cams with Adjustable Timing,Dwell & a Resolver 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided (19LBS) 11/7 |
1980-4310 |
Ametek Gemco Rotating Cam Limit Switch like 1980-402-R-DP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4X Rated 304 Stainless Steel Enclosure 02 = 2 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Timing Dial Window is to be provided 1/7 |
1980-4325 |
Ametek Gemco Rotating Cam Limit Switch like Model 1980-406-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 304 Stainless Steel Enclosure, cover, latches, bearing flanges & flange bolts. 3/4 Inch 316 Stainless Input Shaft. Meets a NEMA 4X Rating 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (24LBS) |
1980-4375 |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-103-X-SP- - 64-L5 Series 1980R with AMCI Style Resolver 1 = NEMA 1 Enclosure 03 = 3 Cams / Circuits / Switches SP = Single Pole Double Throw Switches 64 = 64 to 1 Gear Reducer L5 = Input Shaft Location |
1980-4376 |
Ametek Gemco Rotating Cam Limit Switch1980-12-06-L-SP Series 1980 12 = NEMA 12 Enclosure 06 = 6 Cams / Circuits / Switches SP = Single Pole Double Throw Switches L = Left Hand Shaft Extension With Pulse Generating Disc & Switch in Circuit # 8
|
1980-4380 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-4380 NEMA 12 Enclosure, 6 Circuit / Cam, Right Hand Shaft Extension, SPDT Switches, with AMCI Resolver SD0495600 |
1980-4382 |
Ametek Gemco 1980 Series Rotating Cam Limit Switch. Similar to part # 1980-407-R-DP-X EXCEPT with a 316 Stainless Steel Shaft cam / main shaft along with a stainless steel drain / breather for the enclosure. NEMA 4 Enclosure, 7 Circuits / Cams, D.P.D.T. Snap Action Switches for all circuits, Right End Shaft Extension. |
1980-4386 |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980-4386 Series 1980R, Standard Resolver Output Compatible with all Gemco Electronic Modules. Resolver # 04535001 4 = NEMA 4X Rated Stainless Steel Enclosure, 304 Stainless Steel enclosure option that includes: 316 SS Camshaft, 304 SS Enclosure, Cover, Latches, Bearing Flanges and Flange Bolts 8 = 8 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial or Timing Dial Window is to be provided S = Straight Drive Extension from Gear Reducer 35 = 35 to 1 Gear Ratio R = Right, Gear Reducer is on the Right Side of the cam box (44LBS) |
1980-4387 |
Ametek Gemco Rotating Cam Limit Switch Like Model 1980-404-R-SP-TD2 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Stainless Steel Enclosure 04 = 4 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD2 = Timing Dial labeled for Counter Clock Wise Rotation Special: 304 stainless steel enclosure & 316 Stainless Steel Shaft The enclosure is a 5-6 circuit size due to TD2 Timing dial Option |
1980-4388 |
Ametek Gemco Rotating Cam Limit Switch Like Model 1980-404-L-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Stainless Steel Enclosure 04 = 4 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD1 = Timing Dial labeled for Clockwise Rotation Special: 304 Stainless Steel Enclosure & 316 Stainless Steel Shaft The enclosure size is a 5 - 6 circuit size due to the TD1 timing dial option |
1980-4390 |
Ametek Gemco Rotating Cam Limit Switch Like Model 1980-407-R-SP-TD2 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Stainless Steel Enclosure 07 = 7 Cams / Circuits / Switches R = Right Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD2 = Timing Dial Labeled for Counter Clock Wise Rotation Special: 304 Stainless Steel Enclosure & 316 Stainless Steel Shaft The enclosure size is a 7 - 8 circuit size |
1980-4430 |
Ametek Gemco Rotating Cam Limit Switch. Like Model 1980-404-X-SP-X-S-28-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure with the 304 Stainless Steel Enclosure option that includes: 316 SS Camshaft, 304 SS Enclosure, Cover, Latches, Bearing Flanges and Flange Bolts 04 = 4 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S = Straight Drive Gear Reducer 28 = 28 to 1 Gear Ratio R = Right End Shaft Location Morris Material Handling Originally |
1980-4447 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-4447 NEMA 4 7 Circuit / Cam / Switch Double Pole Double Throw Switches With Resolver With Stainless Steel Drain / Breather
|
1980-4451 |
Ametek Gemco Rotating Cam Limit Switch Model Like 1980-1204-D-SPG-R-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 12 = NEMA 12 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Dual Shaft Extensions from Enclosure, 2 SPG = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch, with Gold Plated Contacts Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boots on the Switch Plunger for additional protection from Moisture & Dust X = No Timing Dial or Dial Window is to be provided (19LBS) 1/8 |
1980-4455 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-TD2 Series 1980 1 = NEMA 1 Enclosure 8 = 8 Cams / Circuits / Switches L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw TD2 = Timing Dial C.C.W. Counter Clock Wise Rotation With 1 Special 30 Degree Cam Circuit. |
1980-4469 |
Ametek Gemco Engineered Product.Similar to part number 1980-408-X-DP-TDI-R-1-L1 except with provisions to mount and couple a customer supplied Dynapar Encoder. Series A5840960010 304 stainless steel enclosure, cover, latches, internal camshaft, bearing flanges & flange bolts Gear Reducer is NEMA 4, (stainless is not available)
|
1980-4478 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-DP-X-M-3-R Series 1980 Vertex S827-6800-30 4 = NEMA 4 Enclosure 6 = 6 Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box DP = DPDT Switches, Double Pole Double Throw X = No Timing Dial M= Multiplier Drive 3 = 1 to 3 Multiplier Ratio R = Right End Shaft Location 1980-4478 |
1980-4484 |
Ametek Gemco Cam Limit Switch Switch Settings 4 to 356 Degrees without a Tool - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 Series 1980 Micro-Adjust Rotating Cam Limit Switch Model 1980-416-R-SP-X 4 = NEMA 4 Enclosure 16 = Qty. 16, Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure L = Left Hand Shaft Extension from enclosure SP = SPDT Switches / Single Pole Double Throw with one NO and one NC contact per switch rated at 15 million cycles X = No Timing Dial or dial window is to be provided Warranty 3 years With NEMA 4X Stainless Adder & 2.5 Inch Shaft Extension without woodruff key and keyslot
|
1980-4500 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) With a special main shaft diameter, keyway & length. Ametek Gemco will assign an engineered part number once the order is acknowledged by engineering. Shaft diameter as it extends from the cam box, 18mm. Shaft keyway 6X3mm, Shaft length from mounting foot center line to end 86mm |
1980-4501 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension from Enclosure DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) With a special main shaft diameter, keyway & length. Ametek Gemco will assign an engineered part number once the order is acknowledged by engineering. Shaft diameter as it extends from the cam box, 18mm. Shaft keyway 6X3mm, Shaft length from mounting foot center line to end 86mm In error provided DPDT switches, change engr # for SPDT switches |
1980-4504 |
Ametek Gemco Engineered Product. Same as part number 1980-4469 with the exception of the removal of the gear reducer. Mount and couple the customer supplied encoder. The encoder is to be a Dynapar Series A125-0012-1-C-320 304 Stainless Steel Enclosure, cover, latches, bearing flanges & flange bolts. 3/4 Inch 316 Stainless Input Shaft. Meets a NEMA 4X Rating 406 17 to 20 Circuit Size Enclosure Dim Also similar to a 1980-408-L-DP-TD1 (57LBS) 40 X 14 X 7 Box |
1980-4510 |
Ametek Gemco Rotating Cam Limit Switch Model, similar to 1980-407-X-SP-R-S-100-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure. 316 Stainless Steel Enclosure, cover & latches. 304 SS for Bearing Flanges & Flange Bolts. 3/4 Inch 316 Stainless Input Shaft. Meets a NEMA 4X Rating 07 = 7 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot option on Switch Plunger for additional moisture protection X = No Timing Dial is to be provided S = Straight Drive Gear Reducer 100 = 100 to 1 Gear Ratio L = Left End Gear Reducer / Main Shaft (34LBS) |
1980-4514 |
Ametek Gemco Specially Engineered Product. Similar to part number 1980-916-Y-DP-X-S-8-R with enclosure heater and thermostat Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 9 = NEMA 9 Rated Enclosure 16 = 16 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand Y = Double Shaft Extension from Enclosure, Two DP = DPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial is to be supplied S = Straight Drive Gear Reducer 8 = 8 to 1 Gear Ratio R- Gear Box mounted on the Right Side (85LBS) |
1980-4515 |
Gemco Rotating Cam Limit Switch Model like 1980-406-X-SP-X-SX-30-L Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial SX= Straight Drive Gear Reducer with a 1/2 Inch Diameter 316 Stainless Steel Shaft 30 = 30 to 1 Gear Ratio L = Left End Shaft Location |
1980-4522 |
Ametek Gemco Rotating Cam Limit Switch Model like a 1980-406-SP-R-X-TD2-R-20-L but with a 316 Stainless Steel Main Shaft Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 4 = NEMA 4 Rated Watertight Enclosure 06 = 6 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand X = No Shaft Extension opposite the gearbox SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 R = Rubber Boot option on Switch Plunger for additional moisture protection TD2 = Timing Dial Labeled for Counter Clock Wise Rotation R - Right Angle Gear Reducer with a 316 Stainless Steel Shaft 20 = 20 to 1 Gear Ratio L = Gear Box is located on the Left Side (30LBS) |
1980-4540 |
Ametek Gemco Rotating Cam Limit Switch Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand D = Double Shaft Extension from Enclosure, Two, Right & Left GSP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided 3 Year Limited Warranty (12LBS) 11/7 |
1980-4541 |
Ametek Gemco Rotating Cam Limit Switch like Model 1980-104-L-GSPR-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension GSPR = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts & Rubber Seals for additional dust & moisture protection X = No Timing Dial or Dial Window is to be provided (12LBS) |
1980-4542 |
Ametek Gemco Rotating Cam Limit Switch like Model 1980-103-L-GSPR-X Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand L = Left Hand Shaft Extension GSPR = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts & Rubber Seals for additional dust & moisture protection X = No Timing Dial or Dial Window is to be provided (11LBS) |
1980-704-X-SP-X-M-3-L |
Ametek Gemco Rotating Cam Limit Switch Model 1980-704-X-SP-X-M-3-L Series 1980 7 = NEMA 7 Enclosure 04= 4 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches, Single Pole Double Throw X = No Timing Dial M = Multiplier Drive 3 = 3 to 1 Gear Multiplier L = Left End Shaft Location |
1980-705-X-SP-X-S-48-R |
Ametek Gemco Rotating Cam Limit Switch Model 1980-705-X-SP-X-S-48-R Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 7 = NEMA 7 Rated Enclosure 07 = 7 Independent Cams / Circuits / Switches X = No Shaft Extension Opposite the Gear Box SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial S= Straight Drive Gear Reducer 48 = 48 to 1 Gear Ratio R = Right End Gear Reducer |
1980-912-R-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch Model 1980-912-R-SP-TD1 Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell 9 = NEMA 9 Rated Enclosure 12 = 12 Independent Cams / Circuits / Switches The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand R = Right Hand Shaft Extension from Enclosure SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial Labeled for C.W. Rotation |
1980R-103-X-DP-R-X-5-L7 |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-103-X-DP-R-X-5-L7 Series 1980R, Standard Resolver Output Compatible with all Gemco Electronic Modules. Resolver # 04535001 1 = NEMA 1 Enclosure 3 = 3 Cams / Circuits / Switches X = No Shaft Extension Opposite Gear Box DP = Double Pole Double Throw Switches X = No Timing Dial or Timing Dial Window is to be provided R = Right Angle Gear Reducer 5 = 5 to 1 Gear Ratio L7 = Left End Shaft Location, Position 7 |
1980R-104-L-2-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-104-L-2-SP-TD1 Series 1980R Cam Box featuring cams with Adjustable Timing & Dwell with Resolver Output 1 = NEMA 1 Rated Enclosure 04 = 4 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension 2 = Standard Output Compatible with AMCI resolver input devices. Resolver # 04535076 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch TD1 = Timing Dial labeled for C.W. Rotation (20LBS) |
1980R-104-L-SP-X |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-104-L-SP-X Series 1980R, Standard Resolver Output Compatible with all Gemco Electronic Modules. Resolver # 04535001 1 = NEMA 1 Enclosure 04 = 4 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension SP = Single Pole Double Throw Switches X = No Timing Dial or Timing Dial Window is to be provided |
1980R-104-R-2-SP-TD1 |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-104-R-2-SP-TD1 1980R= Series 1980 with Resolver Output 1 = NEMA 1 Enclosure 4 = 4 Cams / Circuits / Switches R = Right Hand Shaft Extension 2 = Standard Output Compatible with AMCI resolver input devices. Resolver # 04535076 SP = Single Pole Double Throw Switches TD1 = Timing Dial for C.W. Rotation (20LBS) |
1980R-1203-L-2-SP-X |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-104-L-2-SP-TD1 Series 1980R Cam Box featuring cams with Adjustable Timing & Dwell with Resolver Output 1 = NEMA 1 Rated Enclosure 03 = 3 Independent Cams / Circuits / Switches L = Left Hand Shaft Extension 2 = Standard Output Compatible with AMCI resolver input devices. Resolver # 04535076 SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch X = No Timing Dial (20LBS) |
1980R-1212-R-SP-X |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-1212-R-SP-X Series 1980R, Standard Resolver Output Compatible with all Gemco Electronic Modules. Resolver # 04535001 12 = NEMA 12 Enclosure 12 = 12 Independent Cams / Circuits / Switches R = Right Hand Shaft Extension SP = Single Pole Double Throw Switches X = No Timing Dial or Timing Dial Window is to be provided |
1980R-416-R-DP-R-X |
Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-416-R-DP-R-X 1980R= Series 1980 with Resolver Output 4 = NEMA 4 Enclosure 16 = 16 Cams / Circuits / Switches R = Right Hand Shaft Extension DP = Double Pole Double Throw Switches R = Rubber Boot on Switch Plunger Option X = No Timing Dial
|
1983-1202-R-HI-A-X |
Ametek Gemco Optical Coupler Rotating Cam Limit Switch model 1983-1202-R-HI-A-X Series 1983 12 = NEMA 12 Enclosure 02 = 2 Circuits / Cam / Switches R = Right Hand Shaft Extension HI = High Power Optical Switch with plug in socket for either AC or DC Opto 22 solid state relays A = OAC Output with AC Output 120 Volt AC at 3 AMPS RMS X = No Timing Dial is to be supplied |
1983-1202-R-L1-X |
Ametek Gemco Optical Coupler Rotating Cam Limit Switch model 1983-1202-R-L1-X Series 1983 12 = NEMA 12 Enclosure 02 = 2 Circuits / Cam / Switches R = Right Hand Shaft Extension L1 = Low Power Optical Switch 3 to 30 VDC with Optically Isolated Outputs 100mA Max. No output relays are provided X = No Timing Dial is to be supplied |
1983-1204-R-HI-D-X |
Ametek Gemco Optical Coupler Rotating Cam Limit Switch model 1983-1204-R-HI-D-X Series 1983 12 = NEMA 12 Enclosure 04 = 4 Circuits / Cam / Switches R = Right Hand Shaft Extension HI = High Power Optical Switch with plug in socket for either AC or DC Opto 22 solid state relays D = ODC Output with DC output 0 - 60 Volt DC at 3 Amps RMS X = No Timing Dial is to be supplied |
1983-1456 |
Ametek Gemco Optical Coupler Rotating Cam Limit Switch model 1983-1456 Series 1983 12 = NEMA 12 Enclosure 4 Low Power Optical Switches SD0310700 4 Hi Power Optical Switches SD0312400 Right Hand Shaft Extension 8/7 |
1986-1536 |
Ametek Gemco Resolver Series 1986 Same as 1986B-1-X-R-X B = 2.25 Inch Square Flange Mount with a 3/8 Inch Diameter Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules X = Single Turn Resolver. No Gear Reducer R = Standard Rear Mount Connector X = No Options 1/7 |
1986-1548 |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 S = Single Turn Resolver, No gear reducer S = Side Mount Connector X = No other options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max Current # 1986A-1-X-S-X (13LBS) 1/7 |
1986-1644A |
Ametek Gemco Engineered part number for a ''special'' or OEM Product. This is a 1980-R-104-L-SP-X with the ''Add a Cam'' feature. Add A Cam includes additional space in the enclosure for one more Circuit / Cam / Switch which the OEM or End User could use for some additional control. One of the 4 cams is 45 degrees. OEM EW Bliss 1992 |
1986-1669 |
Ametek Gemco Resolver Series 1986 model 1986A-1GR02-S-X A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 GR02 = Single Turn Resolver with Internal Gear Reducer with a 2 to 1 Gear Ratio S = Side Mount / Right Angle Connector X = No exposure options Angle Position Code 3798 Part No 79507 1/7 |
1986-1681 |
Ametek Gemco Resolver. Replaced by 1986A-1-GR300-R-X 1/7 |
1986-1764 |
Ametek Gemco Resolver. Special 2.06'' Flange Mount Resolver with side mount electrical connector & C&A Wiring (8LBS) |
1986-1781A |
Ametek Gemco Resolver Assembly, AMCI Comp, Single Turn, was 19861781 |
1986-1834 |
Ametek Gemco |
1986-1933 |
Ametek Gemco Resolver see 1986A-1-GR16-R-X 1/7 |
1986-1993 |
Ametek Gemco Resolver Same as 1986A-2-GR14-R-X 1986A = Standard Foot Mount with a 3/4 Inch Diameter Input Shaft 2 = Special output compatible with AMCI resolver input devices. Resolver 04535076 GR14 = Single Turn Resolver, Internal Precision Gear Reducer with a 14 to 1 Gear Ratio R = Standard Rear Mount Connector wired to match AMCI X = No other options 6 Weeks to ship 1/7 |
1986-2004 |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver for use in limited space applications 2.06 Square Flange Mount with a 3/8 Inch Input shaft Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 Single Turn Resolver, No gear reducer Side Mount Connector No options Enclosure NEMA 4 Maximum RPM 5000 Shaft Loading Axial 45 LBS Maximum Shaft Loading Radial 45 LBS Maximum 2 Weeks (4LBS) Same as 1986C-X-S-X |
1986-2053 |
Ametek Gemco Resolver. Similar to a 1986B-1-GR7-R-X with a Flat Shaft Extension 1986B = 2.25 Inch Square Flange Mount. 3/8 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules Resolver # 04535001 GR = Single turn resolver with internal gear reducer 7 = 7 to 1 Gear Ratio R = Standard Rear Mount Connector X = no other options |
1986-2097 |
Ametek Gemco 1986 Resolver. Dual Resolver Geared to 1 :1 with each Resolver Wired to a 10 Pin MS Connector |
1986-XXXX |
Ametek Gemco Resolver. Similar to 1986I-1-X-S-X except with a 10 Pin MS Connector on the back side of the cover. An engineered part number will be assigned at time of any order |
1986A-1-D1-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-D1-R-X A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 D1 = 64 Turn Dual Resolver. (outputs 1 & 2 only) R = Standard Rear Mount Connector X = No other options |
1986A-1-GR03-R-E |
Ametek Gemco Resolver Series 1986 model 1986A-GR03-R-E A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 GR03 = Single Turn Resolver with Internal Gear Reducer with a 3 to 1 Gear Ratio R = Standard Rear Mount Connector E = Stainless Steel Input Shaft and Corrosion Resistant Epoxy Coating on all exposed metal Corrosion Resistant Epoxy Coating on all exposed metal
|
1986A-1-GR10-R-X |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 GR10 = Single Turn Resolver with internal gear reducer 10 to 1 Ratio R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max |
1986A-1-GR16-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-GR16-R-X A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 GR16 = Single Turn Resolver with Internal Gear Reducer with a 16 to 1 Gear Ratio R = Standard Rear Mount Connector X = No exposure options |
1986A-1-GR18-B60-PSA |
Ametek Gemco Resolver Series 1986 model 1986A-1-GR18-B60-PSA A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 GR18 = Single Turn Resolver with Internal Gear Reducer with a 18 to 1 Gear Ratio B60 = Side Exit Potted Pigtail with Bare Leads by 60 Foot Long P = Additional Protective Shaft Seal for high pressure wash down environments SA = All Stainless Steel Construction for mounting configuration ''A'' Includes Stainless Steel Mounting Foot
|
1986A-1-GR2-R-X |
Ametek Gemco Resolver. Series 1986. Standard Foot Mount 3/4 Inch Input Shaft. Standard Output, compatible with all Gemco Electronic Modules. Single Turn Resolver with internal gear reducer 2 to 1 Ratio. Standard Rear Mount Connector |
1986A-1-GR20-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-GR20-R-X A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 GR20 = Single Turn Resolver with Internal Gear Reducer with a 20 to 1 Gear Ratio R = Standard Rear Mount Connector X = No exposure options |
1986A-1-GR300-R-X |
Ametek Gemco Resolver. Replacement for resolver 1986-1681 Change made to gearing. Precision anti-backlash gears for better accuracy. Replacement is bolt in identical except for being about 1 inch shorter in length 1986A-1-GR300-R-X Series 1986A = Standard Foot Mount, 3/4 Inch Input Shaft Dia 1 = Standard Output Compatible with all Gemco Electronic Modules GR300 = Single Turn Resolver with internal gear reducer 300 to 1 ratio R = Standard Rear Mount Connector X = No other options (10LBS) |
1986A-1-GR40-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-GR40-R-X A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 GR40 = Single Turn Resolver with Internal Gear Reducer with a 40 to 1 Gear Ratio R = Standard Rear Mount Connector X = No exposure options |
1986A-1-GR42-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-GR16-R-X A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 GR40 = Single Turn Resolver with Internal Gear Reducer with a 40 to 1 Gear Ratio R = Standard Rear Mount Connector X = No exposure options |
1986A-1-GR58-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-GR58-R-X A = Standard Foot Mount 3/4 Inch Input Shaft 1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001 GR58 = Single Turn Resolver with Internal Gear Reducer with a 58 to 1 Gear Ratio R = Standard Rear Mount Connector X = No exposure options |
1986A-1-X-R-E |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver. A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector E = Stainless Steel Input Shaft and corrosion resistant epoxy coating on all exposed metal Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max |
1986A-1-X-R-X-S30R |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 SD = Straight Drive Gear Reducer 30 = 30 to 1 Gear Ratio R = Shaft on Right Side
|
1986A-1-X-S-X |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 S = Single Turn Resolver, No gear reducer S = Side Mount Connector X = No other options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max Was 1986-1548 (13LBS) |
1986A-2-D1-R-X |
Ametek Gemco Resolver 1986A = Standard Foot Mount with a 3/4 Inch Diameter Input Shaft 2 = Special output compatible with AMCI resolver input devices. Resolver 04535076 D1 = 64 Turn Dual Turn Resolver (outputs 1 and 2 only) R = Standard Rear Mount Connector wired to match AMCI X = No options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max |
1986A-2-GR14-R-X |
Ametek Gemco Resolver 1986A = Standard Foot Mount with a 3/4 Inch Diameter Input Shaft Same as a AME-1986-1993 2 = Special output compatible with AMCI resolver input devices. Resolver 04535076 GR14 = Single Turn Resolver, Internal Precision Gear Reducer with a 14 to 1 Gear Ratio R = Standard Rear Mount Connector wired to match AMCI X = No other options 6 Weeks to ship |
1986A-2-X-R-X |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver A = Standard Foot Mount with a 3/4 Inch Input Shaft 2 = Special Output Compatible with AMCI Resolver Input Devices, Resolver # 04535076 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max (6LBS) |
1986A-4-GR03-R-SA |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver. A = Standard Foot Mount with a 3/4 Inch Input Shaft 4 = Special Output compatible with Modiconmotion cards. Resolver # 04535076 GR03 = Single Turn Resolver with internal gear reducer 3 to 1 ratio R = Standard Rear Mount Connector SA = All Stainless Steel Construction for mounting configuration ''A'' Includes Stainless Steel Mounting Foot NEMA 4 Enclosure Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max |
1986A-DN-GR09-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-DN-GR09-R-X A = Standard Foot Mount 3/4 Inch Input Shaft DN = DeviceNet Output. Resolver 04535001 GR09 = Single turn resolver with internal gear reducer 9 to 1 ratio R = Standard Rear Mount Connector, only type available for DeviceNet X = No other options (7LBS) |
1986A-DN-GR6-1-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-DN-GR6-1-R-X A = Standard Foot Mount 3/4 Inch Input Shaft DN = DeviceNet Output. Resolver 04535001 (rear connector only GR06 = Single turn resolver with internal gear reducer 6 to 1 ratio R = Standard Rear Mount Connector X = No other options (10LBS) |
1986A-DN-X-R-X |
Ametek Gemco Resolver Series 1986 model 1986A-DN-X-R-X A = Standard Foot Mount 3/4 Inch Input Shaft DN = DeviceNet Output. Resolver 04535001 X = Single turn resolver R = Standard Rear Mount Connector, only type available for DeviceNet X = No other options (7LBS) |
1986A1XRX |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max Same as SD0284C & SD0284200 (6LBS) |
1986B-1-GR7-R-X |
Ametek Gemco Resolver 1986B-1-GR7-R-X 1986B = 2.25 Inch Square Flange Mount with a 3/8 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules Resolver # 04535001 GR = Single turn resolver with internal gear reducer 7 = 7 to 1 Gear Ratio R = Standard Rear Mount Connector X = no other options |
1986B1XRX |
Ametek Gemco Resolver Series 1986 B = 2.25 Inch Square Flange Mount with a 3/8 Inch Diameter Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules X = Single Turn Resolver. No Gear Reducer R = Standard Rear Mount Connector X = No Options |
1986C-1-GR20-S-S |
Ametek Gemco Resolver for Absolute Rotary Sensing on the most demanding applications C = 2.06 Inch Square Flange Mount with a 3/8 Inch Diameter Input shaft 1 = Standard Output compatible with all Gemco Electronic Modules & Autotech. Gemco 04535001 GR20 = Gear Reducer with a 20 to 1 Gear Ratio S = Side Mount Connector S = Stainless Steel Construction. Includes Input Shaft, Bearing Housing & Can Assembly |
1986C-1-X-R-P |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver C = 2.06 Square Flange Mount with a 3/8 Inch Input shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector P = Additional Protective Shaft Seal for High Pressure Wash Down Applications Enclosure NEMA 4 Maximum RPM 5000 Shaft Loading Axial 45 LBS Maximum Shaft Loading Radial 45 LBS Maximum (4LBS) |
1986C-1-X-R-X |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver for use in limited space applications C = 2.06 Square Flange Mount with a 3/8 Inch Input shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 Maximum RPM 5000 Shaft Loading Axial 45 LBS Maximum Shaft Loading Radial 45 LBS Maximum 2 Weeks (4LBS) |
1986C-1-X-S-X |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver for use in limited space applications C = 2.06 Square Flange Mount with a 3/8 Inch Input shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver, No gear reducer S = Side Mount Connector X = No options Enclosure NEMA 4 Maximum RPM 5000 Shaft Loading Axial 45 LBS Maximum Shaft Loading Radial 45 LBS Maximum 2 Weeks (4LBS) Same as 1986-2004 |
1986D-1-X-R-X |
Ametek Gemco Inline Resolver. 2.50 Inch Face Mount. 5/8 Inch Input Shaft |
1986E-1-D2-R-X |
Ametek Gemco Resolver 1986E-1-D2-R-X E = 100mm Face Mount with a 5/8 Inch Diameter Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules. Resolver part 04535001 D2 = 128 Turn Dual Resolver. Outputs 1 and 2 only R = Standard Rear Mount Connector X = No other options |
1986F-1-X-R-X |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver. F = 2.50 Inch Square Flange Mount with a 5/8 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector X = No options Enclosure NEMA 13 Max RPM 5000 Shaft Loading Axial 200 LBS Max Shaft Loading Radial 400 LBS Max |
1986F-2-X-R-X |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver F = 2.50 Inch Square Flange Mount with a 5/8 Inch Input Shaft 2 = Special Output Compatible with AMCI Resolver Input Device, Resolver# 04535076 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector X = No options Enclosure NEMA 13 Max RPM 5000 Shaft Loading Axial 200 LBS Max Shaft Loading Radial 400 LBS Max |
1986G-1-GR40-S-X |
Ametek Gemco Resolver Series 1986 G = 3 X 4 & 3/4 Inch Square Flange Mount, 5/8 Inch Input Shaft, NEMA 13 1 = Standard Output Compatible with all Gemco Electronic Modules GR40 = Gear Reducer Ratio of 40 to 1 CE Approval S = Side Mount Connector X = No other options |
1986G-1-GR60-S-X |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver G = 3'' X 4-3/4 Inch Square Flange Mount with a 5/8 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 GR06 = Single Turn Resolver with internal gear reducer 6 to 1 Ratio S = Side Mount Connector X = No options R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max |
1986H2D3SX |
Ametek Gemco Resolver. Servo Mount 1/4 Inch Diameter Input Shaft |
1986MD-1-AL-1-T1 |
Ametek Gemco Mill Duty Resolver Housing Series 1986 model 1986MD-1-AL-1-T1 MD = Mill Duty Housing 1 = 1/4 Inch Plate Steel Housing with plate steel bolted cover sized for single turn resolver AL = Standard 3/4 Inch Input Shaft exiting Left End of Housing 1 = Standard 1 to 1 Gearing, between input shaft & resolver T1 = Resolver is wired to a terminal strip inside the housing |
1986XP-1-D1 |
Ametek Gemco Resolver Series 1986 model 1986XP-1-D1 XP = Expolsion Proof Resolver 4.5 Inch Square Mounting 3/8 Inch Input Shaft 1 = Standard Output compatible with all Gemco electronic modules. Resolver # 04535001 D1 = 64 turn Dual Resolver (outputs 1 & 2 only) UL Listed E10493 CSA Certified LR27991 Compliance: NEC Class 1, Div 1, Groups C & D Class II, Groups E, F & G CSA Standard C22.2 No. 30
|
1986XP-1-GR10 |
Ametek Gemco Resolver Series 1986 model 1986XP-1-GR10 XP = Expolsion Proof Resolver 4.5 Inch Square Mounting 3/8 Inch Input Shaft 1 = Standard Output compatible with all Gemco electronic modules. Resolver # 04535001 GR10 = Single Turn Resolver with Internal Gear Reducer 10 to 1 Ratio UL Listed E10493 CSA Certified LR27991 Compliance: NEC Class 1, Div 1, Groups C & D Class II, Groups E, F & G CSA Standard C22.2 No. 30
|
1986XP-1-GR12 |
Ametek Gemco Resolver Series 1986 model 1986XP-1-GR12 XP = Explosion Proof Resolver 4.5 Inch Square Mounting 3/8 Inch Input Shaft 1 = Standard Output compatible with all Gemco electronic modules. Resolver # 04535001 GR10 = Single Turn Resolver with Internal Gear Reducer 12 to 1 Ratio UL Listed E10493 CSA Certified LR27991 Compliance: NEC Class 1, Div 1, Groups C & D Class II, Groups E, F & G CSA Standard C22.2 No. 30 |
1986XP-1-X |
Ametek Gemco Resolver Series 1986 model 1986XP-1-X XP = Expolsion Proof Resolver 4.5 Inch Square Mounting 3/8 Inch Input Shaft 1 = Standard Output compatible with all Gemco electronic modules. Resolver # 04535001 X = Single Turn Resolver. No Gear reducer UL Listed E10493 CSA Certified LR27991 Compliance: NEC Class 1, Div 1, Groups C & D Class II, Groups E, F & G CSA Standard C22.2 No. 30 (10LBS) |
1989-1540A |
Ametek Gemco PLS. Series 1989 Quik-Set III Multi Turn Programmable Limit Switch. NEMA 12 Enclosure. Triac Output Module. |
1989-1836 |
Ametek Gemco PLS Module |
1989-1848 |
Ametek Gemco Quik-Set III CPU Module with Reset & Binary Output (6LBS) |
1989-1850 |
Ametek Gemco 1989 Quick Set III, a special 4 Digit engineered part number would be established at the time of any order. This special system would be similar to a 1989A16R12SEA3MC12AC but will have 4 motion detectors. This system will be for a single turn resolver and offer 12 solid state programmable outputs and 4 programmable motion detectors and one fault check relay, multi-program and a 4-20mA output of position or velocity all mounted in a NEMA 12 enclosure 12/7 |
1989-A-16-R-12-S-C-K-X |
Ametek Gemco Quik-Set III Multi Turn Programmable Limit Switch |
1989-A-16-R-12-S-E-K-R-X |
Ametek Gemco Programmable Limit Switch 16 Circuit Quik-Set III with Standard Output Package 1989-A-16-R-12-S-E-K-R-X A = Complete System CPU and Keyboard 16 = 16 Output Circuits R = Resolver Input 12 = 12 Bit Resolution, up to 4,096 Positions S = Single Turn Resolver E = Current Sinking Output. (use with Gemco output modules) K = Standard Option Package includes: O (remote preset to reset) U (selectable speed offset, 4 step) M (multiprogam) C (fault check) R = Remote Serial Display RS422 Transmitter (requires display) X = No Output Module Package
|
1989-A-16-R-14-64-E |
Ametek Gemco Programmable Limit Switch 16 Circuit Quik-Set III with Special Options 1989-A-16-R-14-64-E-R A = Complete System CPU and Keyboard 16 = 16 Output Circuits R = Resolver Input 14 = 14 Bit Resolution, up to 16,384 Positions, R Input Only 64 = 64 Turn Dual Resolver E = Current Sinking Output (use with Gemco output modules)
|
1989-A-16-R-14-64-E-R |
Ametek Gemco Programmable Limit Switch 16 Circuit Quik-Set III with Special Options 1989-A-16-R-14-64-E-R A = Complete System CPU and Keyboard 16 = 16 Output Circuits R = Resolver Input 14 = 14 Bit Resolution, up to 16,384 Positions, R Input Only 64 = 64 Turn Dual Resolver E = Current Sinking Output (use with Gemco output modules) R = Remote Serial Display RS422 Transmitter (Display Required) any two options max. |
1989-A-32-R-12-S-E-M |
Ametek Gemco Quik-Set II Multiturn PLS 1989-A-32-R-12-S-E-M A = Complete system CPU and Keypad 32 = 32 Output Circuits R = Resolver Input 12 = 12 Bit resolution / 4,096 Positions S = Single Turn Resolver E = Program Output Current Sinking M = Multi-program |
1989-A-48-R-12-128-E-A3-C |
Ametek Gemco Programmable Limit Switch. Quik-set III Multiturn 1989-A-48-R-12-128-E-A3-C A = Complete System CPU & Keypad 48 = 40 Output Circuits. 2 Additional 16 Circuit Output Modules are required R = Resolver Input 12 = 12 Bit Resolution / 4,096 Positions per Turn 128 = 128 Turn Resolver E = Current Sinking, Program Output A3 = Analog Output 4 to 20 mA, any two options maximum C = Fault Check Relay |
1989-A-48-R-12-S-E-O |
Ametek Gemco Quik-Set II Multiturn PLS 1989-A-48-R-12-S-E-O A = Complete system CPU and Keypad 48 = 48 Output Circuits R = Resolver Input 12 = 12 Bit resolution / 4,096 Positions S = Single Turn Resolver E = Program Output Current Sinking O = Remote Preset to Reset |
1989-CA-16-R-12-S-E-H-R |
Ametek Gemco Quik-Set III Multi Turn Programmable Limit Switch AME-1989-CA-16-R-12-S-E-H-R |
1989-CA-16-R-12-S-E-R |
Ametek Gemco Quik-Set III Multi Turn Programmable Limit Switch AME-1989-CA-16-R-12-S-E-R |
1989-CA-16-R12-S-E-H-RMO |
Ametek Gemco CPU Module for a 1989 Quik-Set III PLS Part AME-1989-CA-16-R12-S-E-H-RMO CA = CPU module Only, no Keypad 16 = 16 Output Circuits R = Resolver Input 12 = 12 Bit Resolution, 4,096 Positions S = Single Turn Resolver E = Current Sinking H = RS232 Transceiver R = Remote Serial Display RS422 Transmitter M = Multi-Program O = Remote Reset to Preset |
1989-CA-48-R-12-S-E-O |
Ametek Gemco Quik-Set II Multiturn PLS 1989-CA-48-R-12-S-E-O CA = CPU Module Only, no Keypad 48 = 48 Output Circuits R = Resolver Input 12 = 12 Bit resolution / 4,096 Positions S = Single Turn Resolver E = Program Output Current Sinking O = Remote Preset to Reset |
1989-KP |
Ametek Gemco Keypad Assembly for a 1989 Quik Set III 6/7 |
1989-O-115-A-E |
Ametek Gemco Output Module Assembly 115 = 115 Volt AC, 50 - 60 Hz A = Solid State Triac, 3 AMP., 280 Volt AC Maximum E = with Gemco Enclosure |
1989-O-115-A-R-S |
Ametek Gemco Output Module. 16 Circuit High Power Output Module with Power Supply & 6 Foot Cable (when ordered separately) 115 = 115 Volt AC 50 - 60 Hz A = Solid state Triac 3 AMP, 280 Volt AC Maximum R = Reset to Preset or Brake Monitor Input S = Standard Panel Mount |
1989-O-115-M-C-S |
Ametek Gemco Output Module for use with 1989 Quik-Set III Multiturn PLS 1989-O-115-M-C-S 16 Circuit High Power Output Module which includes the Power Supply and a 6 Foot Connection Cable 115 = 115 Volt AC, 50 - 60 Hz. Input M = Mechanical Relays, SPDT / Single Pole Double Throw, 10 AMP C = Fault Check Relay Option S = Standard Panel Mount |
1989-O-115-M-S |
Ametek Gemco Module. 16 Circuit High Power Output Module with Power Supply with 6 Foot Cable (when ordered separately) 115 = 115 Volt AC, 50 - 60 Hz M = Mechanical relay SPDT 10 AMP S = Standard Panel Mount No output module options |
1990DN-PLS8-X |
Ametek Gemco Interface. DeviceNet Resolver Interface Module. Plugs in as a Node on a Control System or DeviceNet Scanner Card. Continues rotary position data is provided with 23-Bit Resolution. Eight built in user programmable set points allow direct control of critical functions. All programming is done over the DeviceNet Network |
1992-E-R-X-X-X |
Ametek Gemco Press-Set Automation Controller. Press-Set System: Controller Output Module with Integral Cable Assembly 1992-E-R-X-X-X E = Current Sinking Digital Output Code Format R = Ram Adjust Software, hardware ordered separately X = Controller Only X = Controller Only, controller accepts 80 - 240 VAC 50/60 Hz, Output module must be specified with an input voltage X = Enclosure, None / Standard |
1992-E-X-16M-1-X |
Ametek Gemco Press-Set Automation Controller. Press-Set System: Controller Output Module with Integral Cable Assembly 1992-E-X-16M-1-X E = Current Sinking Digital Output Code Format X = Standard Software 16M = 16 Mechanical Relay S.P.D.T. 10 AMP, standard 1 = Input Voltage for the output module, 115 VAC 50/60 Hz. standard X = Enclosure, None / Standard |
1995-1446 |
Ametek Gemco Display. Remote Circular Display for the 1992 Press-Set Controller |
1995-1512 |
Ametek Gemco Programmable Limit Switch. Micro-Set Series 1995 PLS Programmer with Brake Monitor & Lockout Security Software |
1995-A-6M-P-X |
Ametek Gemco Micro-Set Programmable Limit Switch. Standard Micro-set PLS-Resolver Input. 1995A-6M-P-X 1995A Micro-set PLS Programmer with Reset & Motion Detect 6M = Qty. 6, Mechanical Relay SPDT 10 AMP P = Special Software with MultiprogramSpeed Offset and Time Based Outputs to standard software features X - Open Chassis - No Enclosure |
1995-A-6M-X-12A |
Ametek Gemco Micro-Set Programmable Limit Switch. Standard Micro-set PLS-Resolver Input. 1995A-6M-X-12A 1995A + Micro-set PLS Programmer with Reset & Motion Detect. 6M = Qty. 6, Mechanical Relay SPDT 10 AMP X = Standard Software 12A = NEMA 12 Enclosure. (programmer only) |
1995-A-6M-X-12B-E6M |
Ametek Gemco Programmable Limit Switch model 1995-A-6M-X-12B-E6M Micro-Set Series 1995 PLS Programmer with Reset to Preset & Motion Detect A = Resolver Input only 6M = Qty. 6 Mechanical Output Relays SPDT @ 10 Amp X =Standard Software 12B = NEMA 12 Enclosure with room for 2 Expansion Modules E6M = Factory Mounted Expansion Module with 6 Mechanical Relays. SPDT @ 10 AMP
|
1995-A-6M-X-X |
Ametek Gemco Micro Set Programmable Limit Switch model 1995-A-6M-X-X with Reset to Preset & Motion Detect A = Resolver Input Only 6M = 6 Mechanical Output Relays. Single Pole Double Throw, 10 AMP X = Standard Software X = Open Chassis - No Enclosure expansion modules ordered separately (6LBS) |
1995-B-6M-P-12A |
Ametek Gemco Programmable Limit Switch model 1995-B-6M-P-12A Micro-Set Series 1995 PLS Programmer with Reset to Preset & Motion Detect B = Resolver Input with Brake Monitor 6M = Qty. 6 Mechanical Output Relays SPDT @ 10 Amp P = Special Software adds multiprogram speed offset & time based outputs to standard software features 12A = NEMA 12- Programmer Only |
1995-B-6M-P-12B-E06M |
Ametek Gemco Programmable Limit Switch model 1995-B-6M-P-12B-E6M Micro-Set Series 1995 PLS Programmer with Reset to Preset & Motion Detect B = Resolver Input with Brake Monitor 6M = Qty. 6 Mechanical Output Relays SPDT @ 10 Amp P = Special Software adds multiprogram speed offset & time based outputs to standard software features 12B = NEMA 12 Enclosure with room for 2 Expansion Modules E6M = Factory Mounted Expansion Module with 6 Mechanical Relays. SPDT @ 10 AMP
|
1995-B-6M-P-X |
Ametek Gemco Programmable Limit Switch model 1995-B-6M-P-X Micro-Set Series 1995 PLS Programmer with Reset to Preset & Motion Detect B = Resolver Input with Brake Monitor 6M = Qty. 6 Mechanical Output Relays SPDT @ 10 Amp P = Special Software adds multiprogram speed offset & time based outputs to standard software features X = Open Chassis - No Enclosure. expansion modules ordered separately (6LBS) |
1995-B-6M-X-X |
Ametek Gemco Micro-Set Programmable Limit Switch model 1995-B-6M-X-X with Reset to Preset & Motion Detect B = Resolver Input with Brake Monitor 6M = 6 Mechanical Relays, SPDT 10 AMP X = Standard Software X = Open Chassis - No Enclosure, expansion modules ordered separately (6LBS) |
1995-E-3A3D-6 |
Ametek Gemco Expansion Modules for the 1995 PLS. 3A3D = Output Relays, Qty 3 AC @ 1 AMP 70 - 250 Volt & Qty 3 DC @ 2 AMP 5 - 60 Volt 6 = 6 Foot Cable Length, Maximum Length 300 Feet Maximum of 4 Output Modules per PLS |
1995-E-6M-6 |
Ametek Gemco Output Expansion Module 1995-E-6M-6 with 6 Mechanical Relays, SPDT @ 10 AMP. Standard Cable 6 Foot long. Over 6 foot add $ 1.00 / foot and change last digit |
1995-L-6M-P-12A |
Ametek Gemco Micro Set Programmable Limit Switch model 1995-L-6M-P-12A with reset to Preset & Motion Detect L = Linear input Only 6M = Qty. 6, Mechanical Output Relays. Single Pole Double Throw, 10 AMP P = Special Software. Adds Multiprogram Speed Offset and Time Based Outputs to the Standard Software 12A = NEMA 12 Enclosure for the programmer only |
1995-L-6M-X-12A |
Ametek Gemco Micro Set Programmable Limit Switch model 1995-L-6M-X-12A with reset to Preset & Motion Detect L = Linear input Only 6M = Qty. 6, Mechanical Output Relays. Single Pole Double Throw, 10 AMP X = Standard Software 12A = NEMA 12 Enclosure for the programmer only |
1995-L-6M-X-X |
Ametek Gemco Micro Set Programmable Limit Switch model 1995-L-6M-X-X with Reset to Preset & Motion Detect L = Linear input Only 6M = Mechanical Output Relays. Single Pole Double Throw, 10 AMP X = Standard Software X = Open Chassis - No Enclosure (expansion modules ordered separately) |
19951446 |
Ametek Gemco Display. Series 1995 Rotary Remote Display. 3/4 Inch L.E.D. Digital Display that also has an L.E.D. Bars every 10 Degrees in a Circular pattern / display. Center Digital Display can indicate either Position or RPM. Ideal for mechanical stamping presses and shears. Display can be mounted up to 1000 feet from programmer |
1996C-RSA-12 |
Ametek Gemco Ram-Set Press Shut Height Control. Ram-Set Controller with Output Board, Standard Software and Binary Output. The Ram-Set allows you to automate the shut height adjustment process. Consistently Set Shut Height to + or - .002 Inches. Stores up to 500 Die Numbers and Shut Height Values. For use on single or double action presses RSA = RS485 Communcation 12 = NEMA 12 Rated Enclosure
|
1996C-X-12 |
Ametek Gemco Ram-Set Press Shut Height Control. Ram-Set Controller with Output Board, Standard Software and Binary Output. The Ram-Set allows you to automate the shut height adjustment process. Consistently Set Shut Height to + or - .002 Inches. Stores up to 500 Die Numbers and Shut Height Values. For use on single or double action presses X = No RS485 Communication 12 = NEMA 12 Rated Enclosure
|
1996C-X-X |
Ametek Gemco Ram-Set Press Shut Height Control. Ram-Set Controller with Output Board, Standard Software and Binary Output. X = no options or enclosure. The Ram-Set allows you to automate the shut height adjustment process. Consistently Set Shut Height to + or - .002 Inches. Stores up to 500 Die Numbers and Shut Height Values. For use on single or double action presses. |
1997-1447 |
Ametek Gemco Gate Hoist Cam Box. 4 Circuit. Right End Input Shaft |
1997-1448 |
Ametek Gemco Gate Hoist Cam Box. 4 Circuit. Left End Input Shaft |
1999-Re-Calibrate |
Ametek Gemco Re-Calibration |
1999-SEM |
Ametek Gemco Semelex II Safetimeter. Test Set for full and part revolution clutches. Includes Meter, Position / Velocity Transducer, Autohand and Accessories |
1999OPT5YRWRNTY |
Ametek Gemco Optional 5 Year Limited Warranty. Includes 4 Annual Re-Calibrations. Shipping costs are not included |
2000-100B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Enclosure Turns required to reset switch 10 Maximum switch setting @ 920 Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-101B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 5 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross |
2000-102B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Qty. 4, Independent Cams / Circuits / Switches with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 10 to 1 Gear Ratio. Cast Aluminum NEMA 4 Rated Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS) |
2000-103B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure Turns required to reset switch 1/8th Maximum switch setting @ 19 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-104B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 30 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross |
2000-105B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 38 Turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-106B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 50 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6 LBS) |
2000-107B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 57 & 1/2 Turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-108B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 80 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross |
2000-109B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 100 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross |
2000-10B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 1/8 Maximum switch setting @ 18 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-110B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 2 Maximum switch setting @ 234 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1112B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 500 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross |
2000-1113B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 4 Maximum switch setting @ 135 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1116B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 6 & 1/2 Maximum switch setting @ 265 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1117B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 300 to 1 Ratio, 4 Cam, Single Pole Double Throw Switches, NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS. |
2000-1118B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 600 to 1 Ratio Gear Ratio, the cam block rotates once every 600 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Enclosure Turns required to reset switch 16 Maximum switch setting @ 555 Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1119B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 600 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS) |
2000-111B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 500 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross |
2000-1122B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated, Cast Aluminum, Red Finish Enclosure, Watertight Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1125B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 4000 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 2000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 4000 to 1 Ratio Gear Ratio, the cam block rotates once every 4000 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated, Cast Aluminum, Red Finish Enclosure, Watertight Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1128B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 4000 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 2000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5333.3 to 1 Ratio Gear Ratio, the cam block rotates once every 5333.3 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated, Cast Aluminum, Red Finish Enclosure, Watertight Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-112B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 1000 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS) |
2000-1130B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 4 Maximum switch setting @ 135 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-1131B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 4 Maximum switch setting @ 135 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1132B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 150 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 135 Input shaft Turns. 4 Turns to Reset (6LBS) |
2000-1133B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 6 & 1/2 Maximum switch setting @ 265 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-1134B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 6 & 1/2 Maximum switch setting @ 265 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1135B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 300 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 265 Input shaft Turns. 6 & 1/2 Turns to Reset (6LBS) |
2000-1136B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 600 to 1 Ratio Gear Ratio, the cam block rotates once every 600 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 16 Maximum switch setting @ 555 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-1137B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 600 to 1 Ratio Gear Ratio, the cam block rotates once every 600 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 16 Maximum switch setting @ 555 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1138B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 600 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 555 Input shaft Turns. 16 Turns to Reset (6LBS) |
2000-1139B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-1140B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 2 Cam / Circuit / Switch with Double Pole Double Throw Snap Action Switches (D.P.D.T.) 2000 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS) |
2000-1142B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-1145B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5333.3 to 1 Ratio Gear Ratio, the cam block rotates once every 5333.3 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-115B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Enclosure Turns required to reset switch 1/8 Maximum switch setting @ 19 & 1/4 Turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance |
2000-116B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 38 Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-118B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 50 to 1 Ratio, 4 Cam, Single Pole Double Throw Switches, NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS. |
2000-11B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 1/4 Maximum switch setting @ 28 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1205 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals This specially engineered switch has Non Standard Cams which allow the switch contacts to be opened for 54 or 306 Degrees. Dependent on whether it is wired for normally open or closed circuits. Standard is 25 or 335 degrees. Other cam dwells are available NEMA 12 Enclosure Turns required to reset switch 1/8th Maximum switch setting @ 19 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1206 |
Ametek Gemco Rotary Limit Switch with an Engineered Part Number Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 Non-Standard Cams S69A allow switch contacts to be opened for 90 or 270 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/8th Maximum switch setting @ 19 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-121B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 100 to 1 Ratio, 4 Cam, Single Pole Double Throw Switches, NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS. |
2000-122B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 250 to 1 Ratio, 4 Cam, Single Pole Double Throw Switches, NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS. |
2000-1234 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Qty. 2, Standard Cams allow switch contacts to be opened for 25 or 335 Degrees Qty. 2, Non-Standard Cams allow switch contacts to be opened for 90 or 270 Degrees NEMA 1 & 12 Enclosure Turns required to reset switch 1/8th Maximum switch setting @ 19 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1235 |
Ametek Gemco 2000 Series Geared Limit Switch. NEMA 1 Enclosure. 50 to 1 Gear Ratio. Single S55, 25 Degree Cam Bottom circuit. Without an electrical switch. This was manufactured for an OEM who probably modified this unit as it does not have a switch (3LBS) 1/7 |
2000-124B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Gear Ratio, Qty. 4, Independent Circuits / Cams / Switches. Precision Snap Switches, Single Pole Double Throw S.P.D.T., NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1256 |
Ametek Gemco Rotary Limit Switch, Series 2000 Worm Gear Type, 100 to 1 Ratio, 2 Cam, U.L. Listed Snap Action Switches, S.P.S.T. Single Pole Single Throw, NEMA 1 & 12 Fibralloy Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. (2 LBS) Old Price |
2000-1271 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 37 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance Like a 2000-4B has an Engineered Part Number for a Special Shaft & Bracket (3LBS) 1/8 |
2000-129B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch, 4 Maximum switch setting @ 135 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-12B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 1/4 Maximum switch setting @ 37 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-130B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch, 6 & 1/2 Maximum switch setting @ 265 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-131B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 600 to 1 Gear Ratio, Qty. 2, Circuits / Cams / switches. Precision Snap Action Switches are Single Pole Double Throw / S.P.D.T. , NEMA 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-132B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 150 to 1 Ratio, 2 Cam, Single Pole Double Throw Switches, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS. |
2000-133B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 6 & 1/2 Maximum switch setting @ 265 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-134B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 600 to 1 Ratio Gear Ratio, the cam block rotates once every 600 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 16 Maximum switch setting @ 555 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-135B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 150 to 1 Gear Ratio. UL Listed S.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 135 Input shaft Turns. 4 Turns to Reset (6LBS) |
2000-137B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/8 Maximum switch setting @ 4 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-138B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 9 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-139B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 3/4 Maximum switch setting @ 37 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-13B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 1/4 Maximum switch setting @ 46 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-140B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 6 Maximum switch setting @ 237 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-141B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 15 & 1/4 Maximum switch setting @ 460 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-142B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-145B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 1/8 Maximum switch setting @ 4 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-146B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 1/4 Maximum switch setting @ 9 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-147B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 1/2 Maximum switch setting @ 19 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-148B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Qty. 2, Independent Circuits / Cams / Switches. UL Listed Precision Snap Action Switches, Double Pole Double Throw / D.P.D.T. that can be wired either Normally Open or Normally Closed. 30 to 1 Gear Ratio. NEMA 4 Cast Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. Standard Dwell Cams of 25 Degrees, other dwells are available (6LBS) |
2000-149B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 2 Cam / Circuit / Switch with Double Pole Double Throw Snap Action Switches (D.P.D.T.) 40 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross |
2000-14B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 1 & 1/2 Maximum switch setting @ 58 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-150B |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 2 Cam / Circuit / Switch with Double Pole Double Throw Snap Action Switches (D.P.D.T.) 50 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross |
2000-151B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 1 & 1/2 Maximum switch setting @ 58 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-152B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 1 & 3/4 Maximum switch setting @ 75 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-153B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 2 Maximum switch setting @ 95 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-154B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 6 Maximum switch setting @ 237 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-155B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 15 & 1/4 Maximum switch setting @ 460 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-156B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-159B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D Turns required to reset switch 1/8 Maximum switch setting @ 4 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-15B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 3/4 Maximum switch setting @ 77 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-160B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D Turns required to reset switch 1/4 Maximum switch setting @ 9 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-161B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D Turns required to reset switch 1/2 Maximum switch setting @ 19 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-162B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D Turns required to reset switch 3/4 Maximum switch setting @ 37 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-163B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D Turns required to reset switch 3/4 Maximum switch setting @ 46 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-164B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 80 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 75 Input shaft Turns. 1 & 3/4 Turns to Reset (6LBS) |
2000-167B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 250 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 237 Input shaft Turns. 6 Turns to Reset (6LBS) |
2000-168B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 500 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 460 Input shaft Turns. 15 & 1/4 Turns to Reset (6LBS) |
2000-169B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 1000 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 920 Input shaft Turns. 29 Turns to Reset (6LBS) |
2000-16B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 3/4 Maximum switch setting @ 94 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-171B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 4 Maximum switch setting @ 135 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (5LBS) |
2000-174B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/16th Maximum switch setting @ 4 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-175B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/16th Maximum switch setting @ 9 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-176B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/8th Maximum switch setting @ 19 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-177B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 28 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-17B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/16th Maximum switch setting @ 4 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-180B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 57 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-181B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 76 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-182B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1 & 1/2 Maximum switch setting @ 96 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-183B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 250 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-185B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 1 & 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 3 LBS Gross |
2000-1872 |
Ametek Gemco Rotary Limit Switch Like 2000-818 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4, Special Cams with 54 Degrees of Dwell 4 Independent Circuits / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 12 Rated Die Cast Enclosure with Fibralloy Cover 2 to 1 Input Shaft Ratio, Every Two Turns of the Main Shaft the Cam Block Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure Includes Woodruff Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) 1/8 |
2000-1899 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type. 3 Circuits / Cams / Switches. S.P.D.T. Switches with a NEMA 1 Enclosure. Special 54 degree Cams. |
2000-189B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 1/16th Maximum switch setting @ 9 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-18B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 20 to 1 Gear Ratio. UL Listed S.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 18 Input shaft Turns. 1/8 Turn to Reset (6LBS) |
2000-190B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Enclosure, Watertight Turns required to reset switch 1/8th Maximum switch setting @ 19 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-191B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 30 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. |
2000-194B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 60 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches - 04537004,, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance |
2000-195B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 80 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches - 04537004,, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance |
2000-196B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 100 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches - 04537004, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance |
2000-197B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 2 Maximum switch setting @ 234 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (5LBS) |
2000-198B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 500 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance |
2000-199B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 4 Rated Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-19B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D Turns required to reset switch 1/4 Maximum switch setting @ 28 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-1B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/16th Maximum switch setting @ 4 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-2003 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 15 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS) |
2000-2004 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 20 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS) |
2000-2005 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 30 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS) |
2000-2006 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (DPDT) Double Pole Double Throw Switches. 5 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
|
2000-2021 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 4 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 15 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (9LBS) |
2000-2025 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 156.25 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (9LBS) |
2000-2027 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 250 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS) |
2000-2030 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 500 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS) |
2000-2033 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 1000 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS) |
2000-2046 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (DPDT) Double Throw Double Pole Switches. 625 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS) |
2000-2048 |
Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (DPDT) Double Throw Double Pole Switches. 1000 to 1 Gear Ratio. NEMA 12 Enclosure Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS) |
2000-20B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders Turns required to reset switch 1/4 Maximum switch setting @ 37 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-2106 |
Ametek Gemco Limit Switch. NEMA 4 Enclosure, 4 Circuit / Cams, 54 Degree Cams (special), S.P.D.T Switches. ( S0006800) Old Price |
2000-2141 |
Ametek Gemco Limit Switch. 4 Circuit, NEMA 1, 5 to 1 Gear Ratio, Larger SPDT Switches, 2 Standard 25 Degree Cams, 2 Special 180 Degree Cams. Similar to the 2000-89B except for two special cams and larger micro switches Old price |
2000-2143 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Special Non Standard Cams allow switch contacts to be opened for 54 or 306 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/16th Maximum switch setting @ 4 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) 1/8 |
2000-2148 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 3 Standard Cams allow switch contacts to be opened for 25 Degrees. 1 Special 75 Degree Cam NEMA 4 Rated Cast Aluminum Enclosure, Watertight Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-2179 |
Ametek Gemco Limit Switch NEMA 4X Enclosure Bronze 2 Circuit 40 to 1 Gear Ratio Standard Dwell Cams |
2000-2180 |
Ametek Gemco Limit Switch OBSOLETE Bronze housing is no longer available. See 2000-15B same configuration NEMA 4 Cast Iron Enclosure |
2000-2184 |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 100 to 1 Ratio, 3 Independent Cams / Switches / Circuits. Single Pole Double Throw Switches, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance This specially engineered unit has 1 Special Cam S68 at 54 Degrees per factory not S-84A which is 75 degrees. Also includes the physically larger micro-switches and a cover spacer to allow space for these larger switches (7LBS) Old price |
2000-21B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D Turns required to reset switch 1/4 Maximum switch setting @ 46 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-2229 |
Ametek Gemco Rotary Limit Switch, Engineered Part # for Shepard Niles Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Special S-68-A Cams allow switch contacts to be opened for 54 or 306 Degrees, dependent on how the switches are wired NEMA 12 Rated Enclosure Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) 1/8 |
2000-2235 |
Ametek Gemco Rotary Limit Switch, NEMA 1 Enclosure, 600 to 1 ratio, 2 Circuit with special S68 Cams |
2000-2237 |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Gear Ratio, Qty. 2, Independent Cams / Circuits / Switches, S.P.D.T. Single Pole Double Throw Precision Snap Switches, NEMA 1 & 12 Enclosure, Special Cams # S-68-A @ 54 Degrees, Maximum Speed 1000 RPM Clock Wise or CCW. 1/2 Inch Diameter Input Shaft includes a # 404 Woodruff Key, 1/2 - 14 American Standard Pipe Thread Entrance (4LBS) |
2000-2248 |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 10 to 1 Ratio, 2 Cam, Single Pole Double Throw Snap Action Switches 2, which are independently adjustable, NEMA 7, Hazardous Location,Cast Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. Max 18 turns to set switch, 1/8 turn to reset switch, Max. Operating Temp 180 F., This unit has optional 54 Degree Cams (2LBS) |
2000-2254 |
Ametek Gemco Geared Limit Switch built and sold exclusively by OEM Account. Altec Industries Inc. NEMA 1 , Rubber Gasket |
2000-2262 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Qty. 4, Non-Standard Cams, S0006900, which allow switch contacts to be opened for 90 or 270 Degrees NEMA 1 & 12 Enclosure Turns required to reset switch 1/8th Maximum switch setting @ 19 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-23B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 80 to 1 Gear Ratio. UL Listed S.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 77 Input shaft Turns. 3/4 Turn to Reset (6LBS) |
2000-2401 |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 100 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 1 & 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 3 LBS Gross Special, includes 2, 54 degree cams & 1, 25 Degree cam. Periods for which Switch Contacts are Opened or Closed. |
2000-2459 |
Ametek Gemco Geared Rotary Limit Switch (3LBS) Old Price |
2000-2463 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Non-Standard Cams S68A allow switch contacts to be opened for 54 or 306 Degrees. Other cam dwells are available NEMA 12 Enclosure Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-2479 |
Ametek Gemco Rotary Limit Switch, Worm Gear Type with a 20 to 1 Gear Ratio. Qty. 2, Independent Cams / Circuits / Switches. U.L. Listed Precision Snap Acting Switches, S.P.D.T. Single Pole Double Throw which can be wired Normally Open or Normally Closed. Both Cams are part # S71A at 240 Degrees. NEMA 1 & 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. (6LBS) |
2000-2489 |
Ametek Gemco Limit Switch. Series 2000 Geared Rotary Limit Switch. 4 Independent Circuits / Cams / Switches. SPDT Switches. 2000 to 1 Gear Ratio. NEMA 4 Enclosure. 5K pot and 1 of the four cams is S-0008400, a 75 degree cam Old price |
2000-2490 |
Ametek Gemco Geared Rotary Limit Switch. 4 Circuit / Cams. 2 Cams are Special 75 Degree Cams. 10 to 1 Gear Ratio with a NEMA 1 Enclosure (2LBS) |
2000-24B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 100 to 1 Gear Ratio. UL Listed S.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 94 Input shaft Turns. 3/4 Turn to Reset (6LBS) |
2000-2516 |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 600 to 1 Gear Ratio, Qty. 2, Independent Cam / Circuit / Switches, S.P.D.T. Single Pole Double Throw Switches, NEMA 4 Rated Watertight Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance S0008700 Cams 150 or 210 Degree (3LBS) |
2000-2539 |
Ametek Gemco Geared Limit Switch. 6 Circuits / Cams / Switches. 250 Gear Ratio. NEMA 12 Enclosure. Single Pole Double Throw Switches (Licon) 25 Degree Cams Old price |
2000-2564 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Bronze Enclosure, Watertight Turns required to reset switch 1 & 1/2 Maximum switch setting @ 58 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Stainless Steel Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) 1/8 |
2000-2583 |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 20 to 1 Ratio, 3 Independent Cams / Switches / Circuits. Single Pole Double Throw Switches, NEMA 1 & 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. Special with all 90 Degree Cams S-69-A & Physically Larger Snap Switches (7LBS) Old price |
2000-25B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 19 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-2617 |
Ametek Gemco Geared Rotary Limit Switch. 5 Independent Circuits / Switches / Cams. SPDT Licon Switches, 5 to 1 Gear Ratio, NEMA 1 Enclosure (4LBS) 1/6 |
2000-2634A |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. Form ''C'' 3 Screw Terminals. The common is shared by both contacts 2 Custom Engineered Cams with 130 Degrees of Dwell 1st Non-Standard Cam S-71-A allows one switch contact to be opened for 240 or 120 Degrees 2nd Non-Standard Cam S-86-A allows one switch contact to be opened for 135 or 225 Degrees NEMA 1 & 12 Enclosure Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-2642 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 2 Special Cams with 30 degrees of dwell 1 Cam S70 with 180 degrees of dwell NEMA 12 Rated Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 28 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance Tall Cover (4LBS) |
2000-264B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders Turns required to reset switch 1/16 Maximum switch setting @ 9 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-266B |
Ametek Gemco |
2000-267B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders Turns required to reset switch 1/2 Maximum switch setting @ 38 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-2687 |
Ametek Gemco Limit Switch. NEMA 4 Aluminum Enclosure, Resolver & Plug, 72 to 1 Ratio. |
2000-2701 |
Ametek Gemco Limit Switch with 300:1, NEMA 4, SPDT, cast iron enclosure, 2x586A cams. |
2000-2703 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears, Steel Cams and a Stainless Steel Shaft 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Fibralloy Enclosure Turns required to reset switch 1/16th Maximum switch setting @ 9.5 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-2704 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004 1 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees 2 Non-Standard Cams S68A allow switch contacts to be opened for 54 or 306 Degrees NEMA 12 Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 28 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-273B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders Turns required to reset switch 7 Maximum switch setting @ 460 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-2757 |
Ametek Gemco Geared Rotary Limit Switch. 5 Independent Circuits / Cams / Switches in a NEMA 1 / 12 Enclosure with a 20 to 1 Gear Ratio and Single Pole Double Throw Precision Snap Action Switches. Cams = Qty. 4 Standard Cams S0005500 @ 25 Degrees & Qty. 1, Special Cam @ S0007000 180 Degrees |
2000-2760 |
Ametek Gemco Rotary Limit Switch, Like 2000-14B Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Non-Standard Cams S68 allow switch contacts to be opened for 54 or 306 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 1 & 1/2 Maximum switch setting @ 58 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-2778 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 1 Standard Cam allow switch contacts to be opened for 25 or 335 Degrees 1 Special Cam S84 allows the switch contacts to be opened for 75 or 285 Degrees Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 46 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-2779 |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Qty. 4, Independent Cams / Circuits / Switches with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 20 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Stainless Steel Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS) 10/5 |
2000-2786 |
Ametek Gemco Series 2000 Worm Gear Type Rotary Limit Switch. 4 Independently Adjustable Standard Cams / Circuits, UL Listed snap action S.P.D.T Switches, NEMA 1 & 12 Fibralloy Enclosure, 100 to 1 Ratio. 1/2 Inch input shaft with woodruff key. Maximum RPM 1000. Maximum operating temperature 180 degree F. |
2000-2791 |
Ametek Gemco Geared Rotary Limit Switch. NEMA 4 Enclosure, 40 to 1 Gear Ratio, 4 Circuit / Cams with Special 54 Degree Cams, S.P.D.T Switches. (S0006800) |
2000-279B |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 4000 to 1 Ratio, 2 Cam, S.P.D.T. Single Pole Double Throw Switches, NEMA 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-28B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch, 6 Maximum switch setting @ 230 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-291B |
Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 2000 to 1 Gear Ratio. UL Listed S.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM (6LBS) |
2000-292B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Enclosure Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-2958 |
Ametek Gemco Rotary Limit Switch. NEMA 7 Enclosure with a 1 k Ohm Pot. |
2000-299B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-29B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 15 & 1/4 Maximum switch setting @ 460 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-2B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/8 Maximum switch setting @ 18 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-300B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft 3 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 6 & 1/2 Maximum switch setting @ 265 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (5LBS) |
2000-3036 |
Ametek Gemco 2000-3036 is a NEMA 1, 2 circuit, 100:1 ratio with 75 degree cams. So the 3036 may mean something else cause its not NEMA 7.
|
2000-3047 |
Ametek Gemco Geared Rotary Limit Switch. Series 2000. NEMA 1 Enclosure. 3 Independent Circuits/ Cams / Switches. Single Pole Double Throw Snap Switches. 20 to 1 Gear Ratio. Special 90 Degree Cams & a Tall Cover 10/7 |
2000-3058 |
Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. 2 Independent Cams / Circuits / Switches with Single Pole Double Throw Snap Action Switches, 60 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F Special engineered part number. With Stainless Steel Input Shaft PM0039100 (6LBS) |
2000-3059 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 2 Standard Cams S005500 in switch positions 1 and 4 allow switch contacts to be opened for 25 or 335 Degrees 2 Special Cams S0006800 in switch positions 2 and 3 allow switch contacts to be opened for 54 or 306 Degrees NEMA 1 & 12 Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 76 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-3063 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Four Independent Circuits / Cam / Switches, UL Listed Snap Action Switches with S.P.D.T. Contacts, Die Cast NEMA 4 Enclosure, 1/2 to 1 input shaft revolution to 1 cam block revolution. For basic switch data see table 2 symbol C Special with Qty. 2, S71 Cams in Circuits 2 & 3 |
2000-3070 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. Form ''C'' 3 Screw Terminals. The common is shared by both contacts 2 Custom Engineered Cams with 130 Degrees of Dwell NEMA 1 & 12 Enclosure Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-3071 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. Form ''C'' 3 Screw Terminals. The common is shared by both contacts 1 Custom Engineered Cam with 200 Degrees of Dwell 1 Custom Engineered Cam with 285 Degrees of Dwell NEMA 1 & 12 Enclosure Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) 11/7 |
2000-3077 |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 2 Standard Cams in positions 1 and 4 allow switch contacts to be opened for 25 or 335 Degrees 2 Optional Cams # S68 in positions 2 and 3 allow switch contacts to be opened for 54 or 306 Degrees NEMA 4 Rated Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 57 & 1/2 Turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-3078 |
Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Ratio, Qty. 3 Non-Standard Cams S84 @ 75 Degrees, Single Pole Double Throw Switches, NEMA 4 Rated Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (4LBS) 11/7 |
2000-30B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-31B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 6 Maximum switch setting @ 230 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-32B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 15 & 1/4 Maximum switch setting @ 460 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-33B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 29 Maximum switch setting @ 920 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-34B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet requirements for NEC Class 1, Group D and Class 2 Groups E,F & G. Cast Iron & Bronze are available Turns required to reset switch, 6 Maximum switch setting @ 230 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (2LBS) |
2000-38B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/8th Maximum switch setting @ 9 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-39B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals # 04537004 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 1/8 Maximum switch setting @ 9 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (5LBS) |
2000-3B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 28 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-40B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders Turns required to reset switch 1/8th Maximum switch setting @ 9 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-43B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 2 Maximum switch setting @ 95 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-47B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 28 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-4B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 37 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-59 |
Ametek Gemco Series 2000 Worm Gear Type Rotary Limit Switch. 2 Cam, 100 to 1 with Special Cams 54 Degree, SPDT |
2000-5B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 46 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-60B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D Turns required to reset switch 1/2 Maximum switch setting @ 28 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-6B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1 & 1/2 Maximum switch setting @ 58 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-73B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 3/4 Maximum switch setting @ 46 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-75B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1 & 1/2 Maximum switch setting @ 58 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-77B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1 & 3/4 Maximum switch setting @ 75 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-7B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 3/4 Maximum switch setting @ 77 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-800 |
Ametek Gemco Rotary Limit Switch 2000-800 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537001 & 04537002 Basic Switch Data see Table 2 Symbol A on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 1 to 1 Input Shaft Ratio, Every 1 Turns of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-801 |
Ametek Gemco Rotary Limit Switch 2000-801 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol A on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 1/2 to 1 Input Shaft Ratio, Every 1/2 Turns of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-802 |
Ametek Gemco Rotary Limit Switch 2000-802 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol A on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 1/3 to 1 Input Shaft Ratio, Every 1/3 Turns of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-803 |
Ametek Gemco Rotary Limit Switch 2000-803 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol A on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 2 to 1 Input Shaft Ratio, Every 2 Turns of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-804 |
Ametek Gemco Rotary Limit Switch 2000-804 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol A on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-805 |
Ametek Gemco Rotary Limit Switch 2000-805 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches D.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol B on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 1 to 1 Input Shaft Ratio, Every 1 Turns of the Main Shaft Cam Rotates Once Maximum Turns to set the switch 0.9, minimum 0.05, 0.025 to reset the switch 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-807 |
Ametek Gemco Rotary Limit Switch 2000-807 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches D.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol B on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 1/3 to 1 Input Shaft Ratio, Every 1/3 Turn of the Main Shaft Cam Rotates Once Maximum Turns to set the switch .3, minimum 0.106, 0.008 to reset the switch 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-808 |
Ametek Gemco Rotary Limit Switch 2000-808 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches D.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol B on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 2 to 1 Input Shaft Ratio, Every 2 Turns of the Main Shaft Cam Rotates Once Maximum Turns to set the switch 1.8, minimum 0.1, 0.050 to reset the switch 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-809 |
Ametek Gemco Rotary Limit Switch 2000-809 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches D.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol B on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft Cam Rotates Once Maximum Turns to set the switch 2.7, minimum 0.15, 0.075 to reset the switch 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-813 |
Ametek Gemco Rotary Limit Switch 2000-818 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 3 Independent Circuits / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 2 to 1 Input Shaft Ratio, Every Two Turns of the Main Shaft the Cam Block Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure Includes Woodruff Keyway & a #404 Woodruff Key 0.0120 Turns to Reset 0.050 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-814 |
Ametek Gemco Rotary Limit Switch 2000-814 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 3 Independent Circuits / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft the Cam Block Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure Includes Woodruff Keyway & a #404 Woodruff Key 0.075 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-815 |
Ametek Gemco Rotary Limit Switch 2000-815 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuits / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 1 to 1 Input Shaft Ratio, Every Turn of the Main Shaft the Cam Block Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure Includes Woodruff Keyway & a #404 Woodruff Key 0.025 Turns to Reset the Switch 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-816 |
Ametek Gemco Rotary Limit Switch 2000-816 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuits / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 1 to 1 Input Shaft Ratio, Every Turn of the Main Shaft the Cam Block Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure Includes Woodruff Keyway & a #404 Woodruff Key 0.0120 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-817 |
Ametek Gemco Rotary Limit Switch 2000-817 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuits / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 1 to 1 Input Shaft Ratio, Every Turn of the Main Shaft the Cam Block Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure Includes Woodruff Keyway & a #404 Woodruff Key 0.008 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-818 |
Ametek Gemco Rotary Limit Switch 2000-818 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuits / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 2 to 1 Input Shaft Ratio, Every Two Turn of the Main Shaft the Cam Block Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure Includes Woodruff Keyway & a #404 Woodruff Key 0.0120 Turns to Reset 0.050 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-819 |
Ametek Gemco Rotary Limit Switch 2000-819 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuits / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover 3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft the Cam Block Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure Includes Woodruff Keyway & a #404 Woodruff Key 0.075 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-820 |
Ametek Gemco Rotary Limit Switch Spur Gear Type with Potentiometer NEMA 12 Rated Die Cast Housing with a Fibralloy Cover Gear Ratio is 1 to 1 from the Main Shaft to the Cam Block & the Potentiometer Two SPDT Switches. Basic Switch Data see symbol A page 12 Potentiometers are rated at 2 Watts Many resistance values are available Quoting a 5K resistance potentiometer Unique mounting features permit the switch to be mounted in any of 3 different positions. Mounting holes are independent of the enclosure cover
|
2000-832 |
Ametek Gemco Rotary Limit Switch 2000-832 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol A on Page 13 NEMA 4 Rated Die Cast Enclosure 1 to 1 Input Shaft Ratio, Every 1 Turn of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (5LBS) |
2000-833 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 4 Enclosure, 1/2 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A |
2000-834 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, UL Listed Snap Action Switches with S.P.D.T. Contacts, Die Cast NEMA 4 Enclosure, 1/3rd to 1 Input Shaft Revolution, 1 Cam Block Revolution. For basic switch data see table 2 symbol A. |
2000-835 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cams / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 4 Enclosure, 2 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A |
2000-836 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cams, Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 4 Enclosure, 3 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A |
2000-837 |
Ametek Gemco Rotary Limit Switch 2000-841 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches D.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol B on Page 13 NEMA 4 Rated Die Cast Enclosure, Watertight 1 to 1 Input Shaft Ratio, Every 1Turn of the Main Shaft Cam Rotates Once Maximum Turns to set the switch 0.9, minimum 0.05, 0.025 to reset the switch 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance |
2000-839 |
Ametek Gemco Rotary Limit Switch 2000-841 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches D.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol B on Page 13 NEMA 4 Rated Die Cast Enclosure, Watertight 1/3 to 1 Input Shaft Ratio, Every 1/3 Turn of the Main Shaft Cam Rotates Once Maximum Turns to set the switch 0.30, minimum 0.16, 0.008 to reset the switch 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance |
2000-841 |
Ametek Gemco Rotary Limit Switch 2000-841 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 2 Independent Circuit / Cams / Switches D.P.D.T. Snap Action U.L. Listed Switches Basic Switch Data see Table 2 Symbol B on Page 13 NEMA 4 Rated Die Cast Enclosure, Watertight 3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft Cam Rotates Once Maximum Turns to set the switch 2.7, minimum 0.15, 0.075 to reset the switch 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance |
2000-842 |
Ametek Gemco Rotary Limit Switch 2000-842 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 3 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 4 Rated Die Cast Aluminum Enclosure 1 to 1 Input Shaft Ratio, Every 1 Turns of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (5LBS) |
2000-844 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Three Independent Circuits / Cam / Switches, UL Listed Snap Action Switches with S.P.D.T. Contacts, Die Cast NEMA 4 Enclosure, 1/3rd input shaft revolution to 1 cam block revolution. For basic switch data see table 2 symbol C. |
2000-847 |
Ametek Gemco Rotary Limit Switch 2000-847 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 4 Rated Die Cast Aluminum Enclosure 1 to 1 Input Shaft Ratio, Every Turn of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 0.025 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-848 |
Ametek Gemco Rotary Limit Switch 2000-848 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 4 Rated Die Cast Aluminum Enclosure 1/2 to 1 Input Shaft Ratio, Every 1/2 Turn of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 0.0120 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-849 |
Ametek Gemco Rotary Limit Switch 2000-849 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 4 Rated Die Cast Aluminum Enclosure 1/3 to 1 Input Shaft Ratio, Every 1/3 Turn of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 0.008 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-850 |
Ametek Gemco Rotary Limit Switch 2000-850 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 4 Rated Die Cast Aluminum Enclosure 2 to 1 Input Shaft Ratio, Every 2 Turns of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 0.050 Turns to Reset 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-851 |
Ametek Gemco Rotary Limit Switch 2000-851 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion 4 Independent Circuit / Cams / Switches S.P.D.T. Snap Action U.L. Listed Switches # 04537004 Basic Switch Data see Table 2 Symbol C on Page 13 NEMA 4 Rated Die Cast Aluminum Enclosure 3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft Cam Rotates Once 1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure Includes Keyway & a #404 Woodruff Key 3/4 -14 N.P.T. Electrical Entrance (4LBS) |
2000-854 |
Ametek Gemco Limit Switch. Series 2000 Spur Gear Type Rotary Limit Switch with Potentiometer 04516086 100 OHM 2 Circuit / Cam / Switches SPDT Switches, Single Pole Double Throw, Basic Switch Data Symbol ''A'' page 13 0.9 Degree of a Turn Maximum setting between settings 0.05 Degree of a Turn Minimum setting between settings 0.025 Degree of a Turn to Reset the Switch 1 to 1 Ratio, Spur Gear Ratio, Cam bock turns once every revolution of the main shaft 1 to 3 Potentiometer Ratio. Potentiometers are rated @ 2 Watts, Linear Taper Standard Cams, 25 or 335 Degree 1/2 Inch Diameter Output Shaft with a No 404 Woodruff Key & Keyway NEMA 4 Rated Enclosure, Watertight (5LBS) 10/7 |
2000-864 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 1 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A |
2000-865 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 1/2 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A |
2000-866 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 1/3 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A |
2000-867 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 2 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A |
2000-868 |
Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 3 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A |
2000-89B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/16 Maximum switch setting @ 4 & 3/4 Turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-8B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 3/4 Maximum switch setting @ 94 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (3LBS) |
2000-90B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Fibralloy Enclosure Turns required to reset switch 1/16th Maximum switch setting @ 9.5 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-91B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/8th Maximum switch setting @ 19 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-92B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/4 Maximum switch setting @ 28 & 1/2 Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-93B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 38 Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-94B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 47 Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-95B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 57 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-96B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 1 & 12 Enclosure Turns required to reset switch 1/2 Maximum switch setting @ 76 & 3/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-97B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Rated Enclosure Turns required to reset switch 1 & 1/2 Maximum switch setting @ 56 & 1/4 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (4LBS) |
2000-98B |
Ametek Gemco Series 2000 Worm Gear Type Rotary Limit Switch. 4 Independent Standard Dwell Cams / Circuits / Switches, UL Listed Snap Action S.P.D.T. Switches, NEMA 1 & 12 Fibralloy Enclosure, 250 to 1 Gear Ratio. 1/2 Inch input shaft with woodruff key. Maximum RPM 1000. Maximum operating temperature 180 degree F. (6LBS) |
2000-99B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft 4 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 12 Enclosure Turns required to reset switch 7 Maximum switch setting @ 460 Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2000-9B |
Ametek Gemco Rotary Limit Switch Series 2000 Worm Gear Type with Bronze Gears & Steel Cams 5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft 2 Independently Adjustable Switches/ Circuits / Cams Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available NEMA 4 Rated Cast Aluminum Enclosure, Watertight Turns required to reset switch 1/16 Maximum switch setting @ 4 & 1/2 turns Up to 1000 RPM Clock Wise or CCW 1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key Maximum Operating Temperature 180 Degrees F 1/2 -14 American Standard Pipe Thread Entrance (6LBS) |
2006-1435 |
Ametek Gemco Geared Rotary Limit Switch. 2006 Series. 60 to 1 Gear Ratio. NEMA 4 Enclosure. Left Hand Shaft Extension. 2 Circuit with SPDT Switches. Gemco compatible resolver |
2006-1464 |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 20 to 1 Gear Ratio, S.P.D.T. Single Pole Double Throw Precision Snap Switches, with Potentiometer 4/7 |
2006-1483 |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2 Circuit, NEMA 4 Enclosure, Left Hand Shaft Extension, 80 to 1 Gear Ratio, Both Snap Switches are Double Pole Double Throw. Special Long Dwell 45 Degree Cams (5LBS) |
2006-1484 |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2 Circuit, NEMA 4 Enclosure, Left Hand Shaft Extension, 40 to 1 Gear Ratio, Both Snap Switches are Double Pole Double Throw. Special Long Dwell 45 Degree Cams (5LBS) |
2006-1505 |
Ametek Gemco Geared Rotary Limit Switch Like 2006-402-L-30-A 1505 = Specially Engineered Product, Unit to include a mounted 500 Ohm Potentiometer that has a 1 to 1 ratio with the cam block 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/8 Shaft Turn required to reset the switch Maximum switch setting at 26 turns, minimum at 1 turn (4LBS) |
2006-1543 |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2 Independent Air Valves, NEMA 4 Enclosure, Left Hand Shaft Extension, 357 to 1 Gear Ratio (6LBS) |
2006-1547 |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 120 to 1 Gear Ratio, Qty 2, S.P.D.T. Single Pole Double Throw Precision Snap Switches & Qty 2, D.P.D.T. Double Pole Double Throw Precision Snap Switches. Qty. 2, 180 Degree Dwell Cams & Qty. 2, Standard Dwell Cams (6LBS) |
2006-1549 |
Ametek Gemco Geared Rotary Limit Switch 2006 Type ''K'' 1549 = Specially Engineered Product Qty. 2, Circuit with SPDT Switches 50 to 1 Gear Ratio NEMA 4 Enclosure, LH Shaft Output 10K Pot with a 1 to 1 Ratio
|
2006-2003 |
Ametek Gemco Type K Rotary Limit Switch, 2 Independent Circuits / Cams / Switches. NEMA 4 Enclosure, Left Hand Shaft Extension, 15 to 1 Gear Ratio, Snap Action Switches are Single Pole Double Throw. This specially engineered unit also includes an External Gear Reducer with a Right Angle Shaft Extension and Mounting Base Plate. 40 to 1 Gear Ratio # SD0315400 (8LBS) |
2006-2015 |
Ametek Gemco Geared Rotary Limit Switch Same as 2006-402-L-30-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/8 Shaft Turn required to reset the switch Maximum switch setting at 26 turns, minimum at 1 turn C-H 10316H-4557-1 (4LBS) |
2006-2017 |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2006-404-L-60-A, 4 Circuit, NEMA 4 Enclosure, Left Hand Shaft Extension, 60 to 1 Ratio, All Switches Single Pole Double Throw. (SPDT) |
2006-402-L-10-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-10-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/8 Turns required to reset the switch Maximum switch setting at 8 & 1/2 turns, minimum at 1/4 turn C-H 10316H-1016-1 (4LBS) |
2006-402-L-10-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-10-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1/8 Turns required to reset the switch Maximum switch setting at 8 & 1/2 turns, minimum at 1/4 turn C-H 10316H-1016-1 (4LBS) |
2006-402-L-1080-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-1080-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 1080 = 1080 to 1 Gear Ratio. Cam Block turns once every 1080 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 13.5 Turns required to reset the switch Maximum switch setting at 954 turns, minimum at 36 C-H 10316H-169-1 (5LBS) |
2006-402-L-1080-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-1080-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 1080 = 1080 to 1 Gear Ratio. Cam Block turns once every 1080 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-4-B-A-DO 13.5 Turns required to reset the switch Maximum switch setting at 954 turns, minimum at 36 C-H (5LBS) |
2006-402-L-120-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-120-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch 1950-1-B-A-DO 1 & 1/2 Turns required to reset the switch Maximum switch setting at 108 turns, minimum at 3 turn C-H 10316H-155-1 (4LBS) |
2006-402-L-120-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-120-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft C = Double Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch 1950-4-B-A-DO 1 & 1/2 Turns required to reset the switch Maximum switch setting at 108 turns, minimum at 3 turn (4LBS) |
2006-402-L-20-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-20-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 20 = 20 to 1 Gear Ratio. Cam Block turns once every 20 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/4 Turns required to reset the switch Maximum switch setting at 17 turns, minimum at 1/2 turn C-H 10316H-1017-1 (4LBS) |
2006-402-L-20-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-20-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 20 = 20 to 1 Gear Ratio. Cam Block turns once every 20 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1/8 Turns required to reset the switch Maximum switch setting at 8 & 1/2 turns, minimum at 1/4 turn (4LBS) |
2006-402-L-270-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-270-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 270 = 270 to 1 Gear Ratio. Cam Block turns once every 270 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3.375 Shaft Turns required to reset the switch Maximum switch setting at 236 turns, minimum at 6.75 turns C-H 10316H-4599-1 (5LBS) |
2006-402-L-30-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-30-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/8 Shaft Turn required to reset the switch Maximum switch setting at 26 turns, minimum at 1 turn C-H 10316H-4557-1 (4LBS) |
2006-402-L-30-B |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-30-B 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft B = One Double Pole Double Throw Snap Action Switch. Can be wired for either normally open or a closed circuit. 8 Screw Terminals per Switch # 1950-4-B-A-DO and One Single Pole Double Throw Snap Action Switch. Can be wired for either normally open or a closed circuit. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/8 Shaft Turn required to reset the switch Maximum switch setting at 26 turns, minimum at 1 turn (5LBS) |
2006-402-L-30-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-30-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 3/8 Shaft Turn required to reset the switch Maximum switch setting at 26 turns, minimum at 1 turn (5LBS) |
2006-402-L-357-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-357-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 357 = 357 to 1 Gear Ratio. Cam Block turns once every 357 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 4.46 Shaft Turns required to reset the switch Maximum switch setting at 350 turns, minimum at 12 turns C-H 10316H-167-1 (5LBS) |
2006-402-L-357-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-357-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 357 = 357 to 1 Gear Ratio. Cam Block turns once every 357 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 4.46 Shaft Turns required to reset the switch Maximum switch setting at 350 turns, minimum at 12 turns (5LBS) |
2006-402-L-40-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-40-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/2 Turns required to reset the switch Maximum switch setting at 35 turns, minimum at 1 turn C-H 10316H-157-1 (4LBS) |
2006-402-L-40-B |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-40-B 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft B = One Double Pole Double Throw Snap Action Switch. Can be wired for either normally open or a closed circuit. 8 Screw Terminals per Switch # 1950-4-B-A-DO and One Single Pole Double Throw Snap Action Switch. Can be wired for either normally open or a closed circuit. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/2 Turns required to reset the switch Maximum switch setting at 35 turns, minimum at 1 turn (5LBS) |
2006-402-L-40-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-40-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1/2 Turns required to reset the switch Maximum switch setting at 35 turns, minimum at 1 turn (5LBS) |
2006-402-L-5-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-5-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/16 Turns required to reset the switch Maximum switch setting at 4 turns, minimum at 1/8 turn C-H 10316H-4556-1 (4LBS) |
2006-402-L-5-B |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-5-B 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft B = 1 Double Pole Double Throw Snap Action Switch. 1 Single Pole Double Throw Switch. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch 1/16 Turns required to reset the switch Maximum switch setting at 4 turns, minimum at 1/8 turn (4LBS) |
2006-402-L-5-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-5-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1/16 Turns required to reset the switch Maximum switch setting at 4 turns, minimum at 1/8 turn (4LBS) |
2006-402-L-60-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-60-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/4 Turns required to reset the switch Maximum switch setting at 53 turns, minimum at 2 turns C-H 10316H-156-1 (4LBS) |
2006-402-L-60-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-60-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 3/4 Turns required to reset the switch Maximum switch setting at 53 turns, minimum at 2 turns (4LBS) |
2006-402-L-80-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-80-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1 Turn required to reset the switch Maximum switch setting at 72 turns, minimum at 2 & 1/2 turns C-H 10316H-4559-1 (4LBS) |
2006-402-L-80-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-L-80-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft C= Double Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1 Turn required to reset the switch Maximum switch setting at 72 turns, minimum at 2 & 1/2 turns (4LBS) |
2006-402-R-10-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-10-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/8 Turns required to reset the switch Maximum switch setting at 8 & 1/2 turns, minimum at 1/4 turn (4LBS) |
2006-402-R-120-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-120-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/2 Turns required to reset the switch Maximum switch setting at 108 turns, minimum at 3 turns C-H 10316H-179-1 (4LBS) |
2006-402-R-120-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-120-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO (5LBS) |
2006-402-R-20-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-20-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 20 = 20 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO (4LBS) |
2006-402-R-270-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-270-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 270 = 270 to 1 Gear Ratio. Cam Block turns once every 270 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3.375 Shaft Turns required to reset the switch Maximum switch setting at 236 turns, minimum at 6.75 turns C-H 10316H-4606-1 (5LBS) |
2006-402-R-30-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-30-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/8 Shaft Turn required to reset the switch Maximum switch setting at 26 turns, minimum at 1 turn C-H 10316H-4561-1 (5LBS) |
2006-402-R-357-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-357-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 357 = 357 to 1 Gear Ratio. Cam Block turns once every 357 turns of the main shaft R = 1950-1408 Switches 4.46 Turns to Reset (4LBS) |
2006-402-R-40-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-40-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams L = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/2 Turns required to reset the switch Maximum switch setting at 35 turns, minimum at 1 turn C-H 10316H-181-1 (4LBS) |
2006-402-R-40-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-40-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft C = Double Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch (4LBS) |
2006-402-R-40-R |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-40-R 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft R = 1950-1408 Slow Make Slow Break Switches, Single Pole Double Throw S.P.D.T., Can be wired for Normally Open or Closed Circuits, 4 Screw Terminals per Switch 1/2 Turn to Reset Switch (4LBS) |
2006-402-R-5-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-5-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO C-H 10316H-1018-1 (4LBS) |
2006-402-R-5-C |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-5-C 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO (5LBS) |
2006-402-R-60-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-60-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/4 Turns required to reset the switch Maximum switch setting at 53 turns, minimum at 2 turns C-H 10316H-180-1 (5LBS) |
2006-402-R-80-A |
Ametek Gemco Geared Rotary Limit Switch 2006-402-R-80-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 02 = 2 Independent Circuits / Switches / Cams R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1 Turns required to reset the switch Maximum switch setting at 72 turns, minimum at 2 & 1/2 turns C-H 10316H-4563-1 (5LBS) |
2006-404-L-10-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-10-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-D0 1/8 Turn to Reset Switch C-H 10316H-1026-1 (6LBS) |
2006-404-L-10-E |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-10-E 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1/8 Turn of Main Shaft is required to Reset the Switch Maximum Switch Setting is at 8 & 1/2 Turns, Minimum is at 1/4 Turn (6LBS) |
2006-404-L-1080-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-1080-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 357 = 1080 to 1 Gear Ratio. Cam Block turns once every 1080 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO C-H 10316H-173-1 (6LBS) |
2006-404-L-120-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-120-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1 & 1/2 Turns required to reset the switch Maximum switch setting at 108 turns, minimum 3 turns C-H 10316H-158-1 (6LBS) |
2006-404-L-120-C |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 120 to 1 Gear Ratio, Qty 2, S.P.D.T. Single Pole Double Throw Precision Snap Switches & Qty 2, D.P.D.T. Double Pole Double Throw Precision Snap Switches. (6LBS) |
2006-404-L-120-E |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 120 to 1 Gear Ratio, D.P.D.T. Double Pole Double Throw Precision Snap Switches (6LBS) |
2006-404-L-20-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-20-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 20 = 20 to 1 Gear Ratio. Cam Block turns once every 20 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-D0 1/4 Turn to Reset Switch C-H 10316H-1027-1 (6LBS) |
2006-404-L-20-C |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 20 to 1 Gear Ratio, Two D.P.D.T. Double Pole Double Throw Precision Snap Switches & Two S.P.D.T. Single Pole Double Throw Precision Snap Switches (6LBS) |
2006-404-L-20-E |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-20-E 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 20 = 20 to 1 Gear Ratio. Cam Block turns once every 20 turns of the main shaft E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1/4 Turn of Main Shaft is required to Reset the Switch Maximum Switch Setting is at 17 Turns, Minimum is at 1/2 Turn (6LBS) |
2006-404-L-270-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-270-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 270 = 270 to 1 Gear Ratio. Cam Block turns once every 270 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO C-H 10316H-4600-1 (6LBS) |
2006-404-L-270-C |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 270 to 1 Gear Ratio, Two D.P.D.T. Double Pole Double Throw Precision Snap Switches & Two S.P.D.T. Single Pole Double Throw Precision Snap Switches (6LBS) |
2006-404-L-30-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-30-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/8 turn to Reset Switch C-H 10316H-4569-1 (6LBS) |
2006-404-L-30-E |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-30-E 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 3/8 Turn of Main Shaft is required to Reset the Switch Maximum Switch Setting is at 26 Turns, Minimum is at 1 Turn (6LBS) |
2006-404-L-357-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-357-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 357 = 357 to 1 Gear Ratio. Cam Block turns once every 270 turns of the main shaft A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO C-H 10316H-175-1 (6LBS) |
2006-404-L-357-E |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 357 to 1 Gear Ratio, D.P.D.T. Double Pole Double Throw Precision Snap Switches (6LBS) |
2006-404-L-40-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-40-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch Switch # 1950-1-B-A-D0 Maximum switch setting at 35 turns, minimum at 1 turn 1/2 Turn to Reset Switch C-H 10316H-160-1 (6LBS) |
2006-404-L-40-E |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-40-E 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1/2 Turn of Main Shaft is required to Reset the Switch Maximum Switch Setting is at 35 Turns, Minimum is at 1 Turn (6LBS) |
2006-404-L-5-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-5-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/16 Turn to Reset Switch Maximum switch setting at 4 turns, minimum at 1/8th turn C-H 10316H-4568-1 (6LBS) |
2006-404-L-5-C |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 5 to 1 Gear Ratio, Two D.P.D.T. Double Pole Double Throw Precision Snap Switches & Two S.P.D.T. Single Pole Double Throw Precision Snap Switches (6LBS) |
2006-404-L-5-E |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 5 to 1 Gear Ratio, D.P.D.T. Double Pole Double Throw Precision Snap Switches (6LBS) |
2006-404-L-60-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-60-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 3/4 Turn to Reset Switch C-H 10316H-159-1 (5LBS) |
2006-404-L-60-C |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 60 to 1 Gear Ratio, Two S.P.D.T. Single Pole Double Throw Precision Snap Switches & Two D.P.D.T. Double Pole Double Throw Switches (5LBS) |
2006-404-L-60-D |
Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 60 to 1 Gear Ratio, Three D.P.D.T. Double Pole Double Throw Precision Snap Switches & One S.P.D.T. Single Pole Double Throw Precision Snap Switches (6LBS) |
2006-404-L-60-E |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-60-E 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 3/4 Turn of Main Shaft is required to Reset the Switch Maximum Switch Setting is at 53 Turns, Minimum is at 2 Turns (6LBS) |
2006-404-L-80-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-80-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch Switch # 1950-1-B-A-DO Maximum switch setting at 72 turns, minimum at 2 & 1/2 turns 1 Turn to Reset Switch C-H 10316H-4571-1 (6LBS) |
2006-404-L-80-E |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-80-E 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Die Cast Enclosure, Watertight 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key 80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO 1 Turn of Main Shaft is required to Reset the Switch Maximum Switch Setting is at 72 Turns, Minimum is at 2 & 1/2 Turns (6LBS) |
2006-404-L40-A |
Ametek Gemco Geared Rotary Limit Switch 2006-404-L-40-A 2006 = Type ''K'' Rotary Limit Switch 4 = NEMA 4 Rated Watertight Die Cast Enclosure 04 = 4 Independent Circuits / Switches / Cams L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway 40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO 1/2 Turn to Reset Switch (6LBS) |
2020-1 |
Ametek Gemco Rotary Limit Switch. Now Obsolete, 1996. Series 2020 Traveling Nut Limit Switch. Qty. 2, 1950-1-B-A-DO S.P.D.T. Precision Snap Switches, Switches can be adjusted between 5 and 100 revolutions of the input shaft. 1/2 inch diameter input shaft. 10 AMP., 600 Volt Maximum |
2110-1404 |
Ametek Gemco Shut Height Monitor Series 2110 LDT Board Digital Output / Sourcing Specially Engineered Brackets C0966900 1/4 |
2110-L1-K0-D0-A0-N0 |
Ametek Gemco Shut Height Monitor Model 2110-L1-K0-D0-A0-N0 2 Channel Analog Output L1 = 952 Digital Input Board K0 = Without Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N0 = No Enclosure Supplied. NEMA 4 & 12 are available |
2110-R1-K0-D0-A0-N0 |
Ametek Gemco Shut Height Monitor Model 2110-R1-K0-D0-A0-N0 2 Channel Analog Output R1 = Resolver Board Input K0 = Without Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N0 = No Enclosure Supplied. NEMA 4 & 12 are available |
2110-R1-K0-D0-A1-N0 |
Ametek Gemco Shut Height Monitor Model 2110-R1-K0-D0-A1-N0 R1 = Resolver Board Input K0 = Without Relay Board D0 = Without Digital Output Board A1 = Two Channel Analog Output, Programmable for Voltage or Current N0 = No Enclosure Supplied. NEMA 4 & 12 are available |
2110-R1-K0-D2-A0-N4 |
Ametek Gemco Shut Height Monitor Model 2110-R1-K1-D2-A0-N4 R1 = Resolver Board Input K0 = Without Relay Board D2 = Sourcing Digital Output Board A0 = Without Analog Board N4 = NEMA 4 Enclosure |
2110-R1-K0-D2-A1-N0 |
Ametek Gemco Shut Height Monitor Model 2110-R1-K0-D2-A1-N4 R1 = Resolver Board Input K0 = Without Relay Board D2 = Sourcing Digital Output Board A1 = Two Channel Analog Output Programmable for Voltage or Current N4 = NEMA 4 Rated Enclosure |
2110-R1-K0-D3-A0-N0 |
Ametek Gemco Shut Height Monitor Model 2110-R1-K0-D3-A0-N0 2110 - Shut Height Monitor R1 = Resolver Board Input K0 = Without Relay Board D3 = TTL Digital Output Board A0 = Without Analog Board N0 = No Enclosure Supplied. NEMA 4 & 12 are available |
2110-R1-K1-D0-A0-N0 |
Ametek Gemco Shut Height Monitor Model 2110-R1-K1-D2-A0-N0 R1 = Resolver Board Input K1 = With Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N0 = No Enclosure |
2110-R1-K1-D0-A0-N4 |
Ametek Gemco Shut Height Monitor Model 2110-R1-K1-D2-A0-N4 R1 = Resolver Board Input K1 = With Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N4 = NEMA 4 Enclosure |
2110-V1-K0-D0-A0-N0 |
Ametek Gemco Shut Height Monitor Model 2110-V1-K0-D0-A0-N0 2 Channel Analog Output V1 = LDT Board Input K0 = Without Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N0 = No Enclosure Supplied. NEMA 4 & 12 are available |
2110-V1-K0-D0-A0-N12 |
Ametek Gemco Shut Height Monitor Model 2110-V1-K0-D0-A0-N12 2 Channel Analog Output V1 = LDT Board Input K0 = Without Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N12 = NEMA 12 Rated Enclosure |
2110-V1-K1-D0-A0-N0 |
Ametek Gemco Shut Height Monitor Model 2110-V1-K1-D0-A0-N0 2 Channel Analog Output V1 = LDT Board Input K1 = With Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N0 = No Enclosure Supplied. NEMA 4 & 12 are available |
2110-V1-K1-D0-A0-N12 |
Ametek Gemco Shut Height Monitor Model 2110-V1-K1-D0-A0-N12 V1 = LDT Board Input K1= With Relay Board, 2 Form C Relays D0 = Without Digital Output Board A0 = Without Analog Board N12 = NEMA 12 Rated Enclosure |
2120-L1-K0-D0-A0-N0 |
Ametek Gemco Series 2120 PLC Interface Module model AME-2120-L1-K0-D0-A0-N0 for accurate, absolute position sensing Standard RS232/485 Communication Port L1 = 952 Digital Input Board K0 = Without Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N0 = No enclosure is to be supplied |
2120-L1-K0-D1-A0-N0 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-L1-K0-D1-A0-N0 for accurate, absolute position sensing Standard RS232/485 Communication Port L1 = 952 Digital Input Board K0 = Without Relay Board D1 = ''Sinking'' Digital Output Type A0 = Without Analog Board N0 = No enclosure is to be supplied |
2120-R1-K0-D0-A0-N0 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D0-A1-N0 for accurate, absolute position sensing. Standard RS232/485 Communication Port R1 = Resolver Input K0 = Without Relay Board D0 = Without Digital Output Board A0 = Without Analog Board N0 = No enclosure |
2120-R1-K0-D0-A1-N0 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D0-A1-N0 for accurate, absolute position sensing. Standard RS232/485 Communication Port R1 = Resolver Input K0 = Without Relay Board D0 = Without Digital Output Board A1 = Two Channel Analog Output Programmable for Voltage or Current N0 = No enclosure |
2120-R1-K0-D0-A1-N4 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D0-A1-N4 for accurate, absolute position sensing. Standard RS232/485 Communication Port R1 = Resolver Input K0 = Without Relay Board D0 = Without Digital Output Board A1 = Two Channel Analog Output Programmable for Voltage or Current N4 = NEMA 4 Enclosure |
2120-R1-K0-D1-A0-N0 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D1-A0-N0 for accurate, absolute position sensing Standard RS232/485 Communication Port R1 = Resolver Board Input K0 = Without Relay Board D1 = ''Sinking'' Digital Output Type A0 = Without Analog Board N0 = No enclosure is to be supplied |
2120-R1-K0-D1-A0-N12 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D1-A0-N12 for accurate, absolute position sensing Standard RS232/485 Communication Port R1 = Resolver Board Input K0 = Without Relay Board D1 = ''Sinking'' Digital Output Type A0 = Without Analog Board N12 = NEMA 12 Rated Enclosure |
2120-R1-K0-D1-A1-N0 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D1-A1-N0 for accurate, absolute position sensing. Standard RS232/485 Communication Port R1 = Resolver Input K0 = Without Relay Board D1 = Sinking Digital Output ''E'', A1 = Two Channel Analog Output Programmable for Voltage or Current N0 = No enclosure |
2120-R1-K0-D2-A0-N0 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D2-A0-N0 for accurate, absolute position sensing Standard RS232/485 Communication Port R1 = Resolver Board Input K0 = Without Relay Board D2 = ''Sourcing'' Digital Output Type A0 = Without Analog Board N0 = No enclosure is to be supplied |
2120-R1-K0-D2-A1-N4 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D2-A1-N4 for accurate, absolute position sensing. Standard RS232/485 Communication Port R1 = Resolver Input K0 = Without Relay Board D2 = Digital Output Board Sourcing A1= Two Channel Output Board Programmable for Voltage or Current N4 = NEMA 4 Rated Enclosure |
2120-R1-K0-D3-A0-N4 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D3-A0-N4 for accurate, absolute position sensing. Standard RS232/485 Communication Port. R1 = Resolver Input K0 = Without Relay Board D3 = TTL Digital Output A0= Without 2 Channel Analog Output Board N4 = NEMA 4 Enclosure |
2120-R1-K0-D3-A1-N0 |
Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D3-A1-N0 for accurate, absolute position sensing. Standard RS232/485 Communication Port. R1 = Resolver Input K0 = Without Relay Board D3 = TTL Digital Output A1 = Programmable for voltage or Current N0 = No Enclosure |
23033 |
Ametek Gemco Pneumatic Air Releasing Cylinder on a 10 Inch Type ''S''Hydraulic Brake Assembly. The parking feature is spring set & pneumatically released. |
23040 |
Ametek Gemco Piston Rod Assembly |
2500-WINN-CD |
Ametek Gemco Software. Communication software, Windows based for programing the 2500 PLS. Programing can be done on your computer rather than on the PLS |
2500C |
Ametek Gemco Main Controller Part # Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500C-B-A-R-A-0A8D-X-12 |
Ametek Gemco Series 2500 Programmable Limit Switch. 2500C-B-A-R-A-0A8D-X-12 B = Blind Unit , Remote Operator Interface Required A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 0A8D = Qty. 8, DC Relays X = No Options 12 = NEMA 12 Enclosure / Main Controller Only Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500C-B-A-R-A-0A8D-X-12A |
Ametek Gemco Series 2500 Programmable Limit Switch. 2500C-B-A-R-A-0A8D-X-12A B = Blind Unit , Remote Operator Interface Required A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 0A8D = Qty. 8, DC Relays X = No Options 12A = NEMA 12 Enclosure with room for up to 2 Panel Mount Expansions Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500C-F-A-R-A-0A6A-X-X |
Ametek Gemco Series 2500 Programmable Limit Switch. 2500C-F-A-R-A-0A6A-X-X F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 0A6A = Qty. 6, AC Solid State Relays Rated @ 3 AMPS X = No Options X = No Enclosure Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500C-F-A-R-A-0A8A-B-12A |
Ametek Gemco Series 2500 Programmable Limit Switch 2500C-F-A-R-A-0A8A-B-12A F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 0A8A = Qty. 8, AC Solid State Relays Rated @ 3 AMPS B = Brake Monitor 12A = NEMA 12 Enclosure with room for up to 2 panel mount expansions Warranty: Limited 1 Year Warranty, Parts & Labor, F.O.B. Gemco |
2500C-F-A-R-A-0A8A-X-X |
Ametek Gemco Series 2500 Programmable Limit Switch. 2500C-F-A-R-A-0A8A-X-X F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 0A8A = Qty. 8, AC Solid State Relays Rated @ 3 AMPS X = No Options X = No Enclosure Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500C-F-A-R-A-0A8D-X-X |
Ametek Gemco Series 2500 Programmable Limit Switch 2500C-F-A-R-A-0A8D-X-X F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 0A8D = Qty. 8, DC Solid State Relays, Rated @ 3 AMPS X = No Options X = No Enclosure Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500C-F-A-R-A-0A8M-X-12A |
Ametek Gemco Series 2500 Programmable Limit Switch 2500C-F-A-R-A-0A8M-X-12A F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 0A8D = Qty. 8, DC Mechanical Relays Rated @ 8 AMPS. (for this option all relays must be mechanical) X = No Options 12A = NEMA 12 Enclosure with Room for 2 Panel Mount Expansions Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500C-F-A-R-A-0A8M-X-X |
Ametek Gemco Series 2500 Programmable Limit Switch 2500C-F-A-R-A-0A8M-X-X F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 0A8D = Qty. 8, DC Mechanical Relays Rated @ 8 AMPS. (for this option all relays must be mechanical) X = No Options X = No Enclosure Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500C-F-A-R-A-4A4D-X-X |
Ametek Gemco Series 2500 Programmable Limit Switch 2500C-F-A-R-A-4A4D-X-X F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 4A4D = Qty. 4, AC Solid state Relays & Qty. 4, DC Solid State Relays, Both Rated @ 3 AMPS X = No Options X = No Enclosure 1 Year Limited Warranty, 1 Year Parts & Labor F.O.B. Gemco |
2500C-F-A-R-A-8A0D-X-12 |
Ametek Gemco Series 2500 Programmable Limit Switch 2500C-F-A-R-A-8A0D-X-12 F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 8A0D = Qty. 8, AC Solid State Relays Rated @ 3 AMPS X = No Brake Monitoring Option 12 = NEMA 12 Enclosure for Main controller Only. No expansion modules Warranty: Limited 1 Year Warranty, Parts & Labor, F.O.B. Gemco |
2500C-F-A-R-A-8A0D-X-X |
Ametek Gemco Series 2500 Programmable Limit Switch 2500C-F-A-R-A-8A0D-X-X F = Stand Alone Unit, Face or Flange Mount A = General Software R = Resolver Input A = AC Input Power 100 to 240 Volt 50 or 60 Hz 8A0D = Qty. 8, AC Solid State Relays, Rated @ 3 AMPS X = No Options X = No Enclosure Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500E |
Ametek Gemco Expansion Module |
2500E-A-0A8D-X |
Ametek Gemco Series 2500 Expansion Module 2500E-A-08D-A A = AC Input Power 100 to 240 Volt, 50 / 60 Hz. 0A8D = Qty. 8, DC Relays X = No Options Warranty 1 Year Parts & Labor F.O.B. Gemco |
2500E-A-8A0D-X |
Ametek Gemco Series 2500 Expansion Module 2500E-A-8A0D-X A = AC Input Power 100 to 240 Volt, 50 / 60 Hz. 8A0D = Qty. 8, AC Relays X =No Options. Warranty: Limited 1 Year Warranty, Parts & Labor, F.O.B. Gemco |
2500R-X |
Ametek Gemco Remote Operator Interface. 2500 Series Warranty 1 Year Parts & Labor F.O.B. Gemco |
279B97H02 |
Westinghouse Solenoid Assembly. See E005055 on a CB-35 5.5 Inch Diameter Brake, includes the Plunger & Solenoid Guides No coil. 3279B97H02 (5LBS) |
3000-107 |
Ametek Gemco Gear Reducer, Right Angle, 30 to 1 Gear Ratio, R4 |
3000-150R |
Ametek Gemco Gear Reducer for a 1980 Series Rotary Limit Switch. 10 to 1 Ratio with a Straight / Parallel Drive . Right Hand. A main shaft must be purchased along with the gear reducer (6LBS) |
3000-167L |
Ametek Gemco Gear Reducer. Straight Drive Gear Reducer with a 200 to 1 Ratio. Not available without a main shaft PM0188503 |
3000150R |
Ametek Gemco Gear Reducer for a 1980 Series Rotary Limit Switch. 10 to 1 Ratio with a Straight / Parallel Drive . A Main Shaft must be purchased with the gear reducer (6LBS) |
3001-1 |
Ametek Gemco 1/2 Inch Sprocket Drive Coupling. Maximum torque rating 300 lb.-in. 1/2inch direct & sprocket drive 404 woodruff keyway & key. 50 turns of the adjusting screw will rotate coupling 360 degrees. |
3001-101 |
Ametek Gemco Coupling. OBSOLETE SEE 3001-3 Adjustable Coupling for Presses. Provides means of changing the position between cam shaft and sprocket in 5 degree increments. 3/4 Inch Shaft Size. Sprockets are sold separately. Sprockets for this coupling work with # 25, #35 or # 50 Size Chain. Sprocket Teeth Available 30, 32, 35, or 36. If sold with a sprocket the sprocket comes mounted to the coupling.If sold less sprocket customer to supply sprocket mounting hardware, Qty.3, 1/4 -20 Bolts. Hardware must not extend more than 1/4 Inch past the sprocket (5LBS) |
3001-2 |
Ametek Gemco 1/2 Inch Direct Drive Coupling. Maximum torque rating 300 lb.-in. 1/2inch direct & sprocket drive 404 woodruff keyway & key. 50 turns of the adjusting screw will rotate coupling 360 degrees. (1LB) |
3001-3 |
Ametek Gemco Coupling. Adjustable Couplings changing timing between cam shaft and sprocket. Loosen Lock Screw and Rotate the Adjustment Screw. 50 Turns = 350 Degrees of rotation. Sprockets are sold separately. Sprockets for this coupling work with #35 Size Chain. Sprocket Teeth Available 30, 32, 35, or 36. If sold with a sprocket the sprocket comes mounted to the coupling.If sold less sprocket customer to supply sprocket mounting hardware, Qty.3, 1/4 -20 Bolts (5LBS) |
3001-4 |
Ametek Gemco Coupling. Adjustable Coupling to facilitate easy Timing Adjustment between the 3/4 Inch Cam Shaft and the 3/4 Inch Drive Shaft. Loosen Lock Screw and Rotate the Adjustment Allen Screw. 50 Turns = 350 Degrees of rotation. Coupling has a 3/4 Inch Shaft Diameter Shaft which Extends 1.5 Inches from the Coupling, Shaft includes a # 606 Woodruff Key & Keyway. Coupling Bore Diameter 3/4 inch with Woodruff Keyway. Overall Length 3.125 Inches. Maximum Torque Capability 785 LB. / IN. (3LBS) |
304 Stainless Steel |
Ametek Gemco Adder for a 304 stainless steel enclosure, cover, latches, camshaft, bearing flanges & flange bolts. The stainless steel enclosure is finished with a Gemco Gray Enamel Finish. It is not polished stainless steel. |
439C394G01 |
Ametek Gemco Brake Shoe & Lining Complete see E019024 |
49974 |
Ametek Gemco Dual Air Reservoir (Old Wagner P/N AD49974) 23 LBS Net |
6'' H 1 |
Ametek Gemco Hydraulic Brake System for Progressive / Controlled Stopping Torque. Torque range of 0 through 150 FT LBS. via Foot Pedal Pressure. System Type H with 1, 6 Inch Hydraulic Brake Assembly J23020. System includes Foot Pedal J008219 & Control Cylinder J017616, Fluid Reservoir / Bleeder, Bleeder Pushbutton J10808 , 100 FT Copper Tubing, Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 V DC, 115 V AC or a manual 1/4 turn valve for operation for the bleeder. Less a 6 X 3 Inch Brake Wheel |
6'' H 2 |
Ametek Gemco 6 Inch Hydraulic Brake System, Qty. 2, Brake Assemblies, Control Cylinder, Pedal, Fluid Reservoir Bleeder, Tubing, Fluid and Fittings for a complete system, less brake wheels. |
6'' HM 1 |
Ametek Gemco Brake System. HM Brake System (with parking) 6 X 3.25 Inch for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 150 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Brake Torque 35 FT LBS. Includes one 6 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel (136LBS) |
6'' HM 2 |
Ametek Gemco Brake System. HM Brake System with parking. 2, 6 X 3.25 Inch Brakes for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 300 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Brake Torque 70 FT LBS. Includes two 6 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel |
71211SN1MM00N0C111C8 |
Ametek Gemco Coil . DC 240 Volt Coil for new style FRB's (1LB) |
76-1200 |
Ametek Gemco Roller Arm. Part of a 04537004 |
8''-H-1 |
Ametek Gemco 8 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 200 LBS. / FT dynamic stopping torque. Includes Qty.1, 8 Inch Hydraulic Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 8 Inch Brake Weight 28 LBS. Overall Width 7 - 1/4 Inch , Height 12 - 9/16 Inch. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually operated. A 8 X 3.25 Inch Brake Wheel is not included |
8''-H-2 |
Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 400 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 8 Inch Hydraulic Brake Assemblies J002779, 230 Volt DC Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314 (189LBS) AME-80200013 |
8''-HM-1 |
Ametek Gemco 8 X 3.25 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 200 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 50 FT LBS. Includes one 8 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 139 LBS Net. |
8''-HM-2 |
Ametek Gemco 8 X 3.25 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 200 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 50 FT LBS. Includes one 8 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 139 LBS Net. |
8020 |
Ametek Gemco AHM / ERC System. Qty. 2, 18 X 8 Inch Type HM Brakes. Includes Qty. 2, J007905 Brake Actuators, Qty. 2, 18 X 8 Type HM Hydraulic Brakes, J066962 Treadle Vale Installation Kit, J0790942 Air Compressor 3/4 HP, J071030 Tubing Installation Kit, J073900 Tubing Kit (2 Hoses & 50 Feet of Tubing) J073903 Tubing Kit (4 Hoses with 200 Feet of Tubing) AHM / ERC Panel, DC 1 X 8 Ratio, Qty 2, PSD0180100 FRB Unit |
8020-0042 |
Ametek Gemco AH/ERC Conversion System. Converts a Type ''H'' Brake System (without parking) into a Electrically Controlled System. Includes one J070943 Air Compressor 3/4 HP 230 VDC., one J070972 AH/ERC Control Panel 230 VDC pre-piped and pre-wired, one J073910 Installation Kit which includes tubing, fittings, unions, gaskets and brake fluid. Panel has one JC54086 Pressure Cluster for 1 & 2 brake systems. ''Small Panel'' 27 Inches Wide X 33 Inches High |
8020-0044 |
Ametek Gemco AH/ERC Brake Conversion System, 480 VAC, includes one 8 to 1 Ratio pressure cluster on 70970 control panel, one 3/4 HP 70942 AC Compressor and J073910 tubing installation kit. For use with existing manual hydraulic foot pedal in cab and existing single 18'' hydraulic brake |
8020-0046 |
Ametek Gemco: Brake System: Conversion: AHM/ERC Conversion System. Converts a Type ''H'' Brake System (without parking) into a Electrically Controlled System. Includes one J070943 Air Compressor 3/4 HP 230 VDC., one J100650 AHM/ERC Control Panel 230 VDC pre-piped and pre-wired, one J073910 Installation Kit which includes tubing, fittings, unions, gaskets and brake fluid. One PSD0180101 Fluid Reservoir Bleeder 230 VDC. Panel has one JC54086 Pressure Cluster for 1 & 2 brake systems. Panel Dim. 33 Inches Wide X 45 Inches High |
8020-0052 |
Ametek Gemco AH/ARC Conversion System from manually operated Type H systems (without parking) to air over hydraulic. (2 brake system) Includes one 3/4 HP motor driven compressor, one pre-piped, pre-wired control panel, one installation kit including hose, tubing, fittings. 230VDC, 8:1 pressure ratio. Air treadle valve sold separately. |
8020-0621 |
Ametek Gemco Conversion System for a 10 Inch Hyd System from H To HM |
8020-1409 |
Ametek Gemco AH/ERC Conversion System for 4 brake system. Includes the following: J070943 Air Compressor 3/4 HP 230VDC, J070896T AH/ERC Control Panel with 2, 8:1 Pressure Clusters & J073910 Tubing Installation Kit. Treadle Valve and fluid reservoir bleeders are not included. |
8020-1433 |
Ametek Gemco Conversion System. Type ''H'' Hydraulic Brake Systems to ''HM'' Hydraulic Brake System with a Parking Feature. for one 14 X 6 Inch Brake. Includes one each of the following: J023437 Brake Actuator, J045767 Control Station switch with Lamp, J070899 Kit Modifier, J073900 Installation Kit with 50 Ft Copper Tubing, 2 Armored Hoses & Fittings, J079462 14 Inch HM Brake Cylinder, PSD0180101 Fluid Reservoir Bleeder 230 VDC |
8020-1440 |
Ametek Gemco AH/ERC Conversion system for use with a single hydraulic brake. Includes 70943 compressor 3/4HP 230VDC, 70984T panel with one 8:1 pressure cluster, 66962 treadle valve installation kit including 107039 treadle valve, 71030 tubing installation kit. |
80200002 |
Ametek Gemco Type H Brake System Qty 1, 6 X 3 |
80200013 |
Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 400 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 8 Inch Hydraulic Brake Assemblies J002779, 230 Volt DC Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314 (189LBS) |
80200015 |
Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 400 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 10 Inch Hydraulic Brake Assemblies J002926, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. Brake Wheels are not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (189LBS) |
80200042 |
Ametek Gemco AH/ERC Conversion System, for 230 VDC, with a Single 8 X 1 Pressure Cluster |
80200052 |
Ametek Gemco AH/ARC Conversion System, VDC |
802002-0288 |
Ametek Gemco Bridge Brake System, Qty. 4, 10X4 Brakes, Single Station, Type A/H-ARC Complete System less brake wheels. Supply voltage 230 VDC, with 7/8 inch brake actuators and 1X5 ratio A/H pressure cluster for maximum torque of 380 LBS FT per brake |
80201500 |
Ametek Gemco AH/ERC, 230 VDC, 2 Brake 18 Inch Hyd Brake, Moving Cab No Pedal |
81101008 |
Ametek Gemco Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 10 Inch Wheel Diameter, Voltage DC with Shunt Wound Coils. 200 FT. LBS. 1 Hour. The TMSC Brake has interlocking shoe arms that allow single point adjustment for lining wear. Brake Weight 165 LBS. Net 190 LBS Gross. A 10 X 3.75 Inch Brake Wheel is not included. This brake is also available to operate via a hydraulic slave cylinder for progressive brake application from a crane cab. A Rectifier for AC Voltages is an available option |
8138 |
Ametek Gemco Belt for the Air Compressor & Motor Assembly |
8210-6-16-A-S-Y-X-X-L |
Ametek Gemco Electro-Thrust Brake Assembly. Series 8210 16 = 16 Inch Diameter Brake / Wheel 6 = 230 Volt DC Thruster Motor A = X-Former Thruster Oil providing an operating range of -13 thru 104 Degrees F S = Setting Delay Valve Included / Brake Setting Times with the Adjustable Valve 0.80 to 3.8 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application Y = Self Adjusting Mechanism providing automatic compensation for lining wear X = No Limit switches X = No Hand Relased L = Left Hand Actuator Orientation Torque Rating 1000 LB FT Built to AISE Specifications (same foot print, relationship to brake wheel & torque as a TM-1665) Spring Applied Electrohydraulic Release L = Left Hand Actuator Orientation (400LBS) |
8210-8-4-A-S-X-X-N-I |
Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications (same foot print, relationship to brake wheel & torque as a TM-83), Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times with the Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. Includes a Non-Latching Hand Release 140 LBS + skid. Ships via motor freight |
8210-8-4-A-S-X-X-X-I |
Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications (same foot print, relationship to brake wheel & torque as a TM-83), Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times with the Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Ships via motor freight |
82101056 |
Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter, 800 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, 320 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal |
909-12-CD-4-R-SP |
Ametek Gemco Kam-Way Linear Limit Switch Series 909-12-CD-4-R-SP 12 = 12 Inches of Active travel CD = Limit Switch with Cable Drive 4 = 4 Switches R = Right Hand Assembly SP = Single Pole Double Throw Switches |
909-66-AA-10-R |
Ametek Gemco Series 909. Since we do not know exact part number this is our best estimate. A 66 Inch Stroke is a special unit |
925-1623 |
Ametek Gemco Linear Cable Reel Sensor. Like model 925-A2-78-72-S-X A2 = 97 to 192 Inch Stroke Mechanical Capacity 78 = 78 Inch Active Stroke 72 = 72 Inches of Initial Lead In Cable S = Single Turn Resolver. Resolver single is to be fed to a converting device, which is not included X = No Other Options Engineer part number and product. Has a gear ratio that allows the 04535001or SD0308900 resolver to turn 1 revolution for every 11 inches of active travel / stroke 1/7 (15LBS) |
925-1675 |
Ametek Gemco Linear Cable Reel Sensor with 60 Inches of Active Stroke and an 18 Inch Lead in Cable 05 |
925-A2-136-90-S-X |
Ametek Gemco Linear Cable Reel Sensor. Model 925-A2-136-90-S-X A2 = 97 to 192 Inch Stroke Mechanical Capacity 136 = 136 Inch Active Stroke Electronically, The single turn resolver will make a 350 degree turn over this length. recommend use of 132 or 138 (6'' increments) 90 = 90 Inches of Initial Lead in Cable S = Single Turn Resolver. Resolver single is to be fed to a converting device which is not included X = No Other Options |
925-A2-144-72-S-X |
Ametek Gemco Linear Cable Reel Sensor. Model 925-A2-144-72-S-X A2 = 97 to 192 Inch Stroke Mechanical Capacity 144 = 144 Inch Active Stroke Electronically, The single turn resolver will turn 350 degrees turn over this length. 72 = 72 Inches of Initial Lead in Cable S = Single Turn Resolver is to be fed to a converting device which is not included X = No Other Options |
925-A2-192-X-S-X |
Ametek Gemco Linear Cable Reel Sensor. Model 925-A2-192-X-S-X A2 = 97 to 192 Inch Stroke Mechanical Capacity 192 = 192 Inch Active Stroke Electronically, The single turn resolver will turn 350 degrees turn over this length. X = 0 Initial Lead In Cable Required S = Single Turn Resolver is to be fed to a converting device which is not included X = No Other Options |
925-A2-78-72-S-X |
Ametek Gemco Linear Cable Reel Sensor. Model 925-A2-78-72-S-X A2 = 97 to 192 Inch Stroke Mechanical Capacity 78 = 78 Inch Active Stroke 72 = 72 Inches of Initial Lead In Cable S = Single Turn Resolver. Resolver single is to be fed to a converting device, which is not included X = No Other Options |
925-B1-168-72-S-X |
Ametek Gemco Linear Cable Reel Sensor. Model 925-B1-168-72-S-X B1 = 193 to 480 Inch Stroke Mechanical Capacity / Single Main Spring 168 = 168 Inch Active Stroke 72 = 72 Inches of Initial Lead In Cable S = Single Turn Resolver. Resolver single is to be fed to a converting device, which is not included X = No Other Options |
925-B1-201-108-S-X |
Ametek Gemco Linear Cable Reel Sensor Model 925-B1-201-108-S-X B1 = 193 to 480 Inch Stroke / Single Spring 201 = 201 Inch Active Stroke 108 = 108 Inches of Initial Cable Lead in S = Single Turn Resolver. Resolver signal is to be fed to a converting device, not included X = No Other Options |
940-0060-3E |
Ametek Gemco Linear Position Sensor 6 Inch Active Stroke 4 to 20mA Loop Power (6LBS) |
940-0070-3E |
Ametek Gemco Linear Position Sensor 7 Inch Active Stroke 4 to 20mA Loop Power (6LBS) |
940-0100-3E |
Ametek Gemco Linear Position Sensor 10 Inch Active Stroke 4 to 20mA Loop Power (6LBS) |
940-0120-3E |
Ametek Gemco Linear Position Sensor 12 Inch Active Stroke 4 to 20mA Loop Power (6LBS) |
940-0180-1E |
Ametek Gemco Linear Position Sensor 18 Inch Active Stroke 0 to 10 VDC 3 Wire (6LBS) |
948001 |
Ametek Gemco Limit Module Supplies 4 Adjustable Set Points / Limits on an LDT or other analog output device Sinking, 0 - 10 Volts DC |
948002 |
Ametek Gemco Limit Module Supplies 4 Adjustable Set Points / Limits on an LDT or other analog output device Sourcing, 0 - 10 Volts DC |
949-003 |
Ametek Gemco Mounting Kit. LDT Mounting Kit includes, Head ''L'' Bracket M0748600 and the Probe Support Bracket SD0411200 |
949-005 |
Ametek Gemco Mounting Kit. Magnet Mounting Kit for LDT's. Non Ferrous Stainless Steel. Requires the use of the Large Split Magnet. For use with probes 940, 950IS, 951, 952 & 952QD (1LB) |
949-019L12 |
Ametek Gemco Cable Connector for a 955A LDT. 5 Pin Straight Connector by 12 Foot Long |
949-019L6 |
Ametek Gemco Cable Connector for a 955A LDT. 5 Pin Straight Connector by 6 Foot Long |
949-021L12 |
Ametek Gemco Cable Connector. 6 Pin, 12 Foot with a straight connector |
949-021L6 |
Ametek Gemco Cable Connector. 6 Pin, 6 Foot with a straight connector |
949-022L12 |
Ametek Gemco Cable Assembly. 6 Pin Connector by 12 Foot with a Right Angle Connector |
949-022L6 |
Ametek Gemco Cable Assembly. 6 Pin Connector by 6 Foot with a Right Angle Connector |
949-023L15 |
Ametek Gemco Cable Assembly 23 Feet |
949001L12 |
Ametek Gemco Cable Assembly. Cable with 12mm Euro Straight Connector, 12 Foot Length. For connection of 955S, 955LC, 956S & 956LC LDT's to the PLS |
949001L6 |
Ametek Gemco Cable Assembly. Cable with 12mm Euro Straight Connector, 6 Foot Length. For connection of 955S, 955LC, 956S & 956LC LDT's to the PLS |
949002L12 |
Ametek Gemco Cable Connector, 4 Pin, 12 Foot with Right angle 12mm Euro Connector. Compatible with 956S & LC LDT''S (1LB) |
949002L6 |
Ametek Gemco Cable Assembly for use with the 955S & LC LDT'S. 4 Pin Micro 12mm Euro Straight Cable by 6 Foot Long (2LBS) |
949003 |
Ametek Gemco Mounting Kit. Probe Mounting Kit. Includes End Clamp M0748600 & Rod Support Bracket SD0411200. Non Ferrous Stainless Steel. For use with probes 940, 950IS, 951, 952 & 952QD Does not include magnet mount bracket |
949005 |
Ametek Gemco Mounting Kit. Magnet Mounting Kit for LDT's. Non Ferrous Stainless Steel with Hardware. Requires the use of the Large Split Magnet. For use with probes 940, 950IS, 951, 952 & 952QD (1LB) |
949011L12 |
Ametek Gemco Cable Assembly with Straight Micro Plug Connector for a 953 VMAX LDT. 12 Foot Long, 5 Pole Turck RK 4.5T-4/S618, 12mm Euro Connector, Shielded |
949011L6 |
Ametek Gemco Cable Assembly with Straight Micro Plug Connector for a 953 VMAX LDT. 6 Foot Long, 5 Pole Turck RK 4.5T-4/S618, 12mm Euro Connector, Shielded |
949012l12 |
Ametek Gemco Cable Connector for a 953 VMAX LDT. 12 Foot, 5 Pin Right Angle 12mm Euro Connector (Shielded) |
949012L6 |
Ametek Gemco Cable Connector for a 953 VMAX LDT. 6 Foot, 5 Pin Right Angle 12mm Euro Connector (Shielded) |
949019L12 |
Ametek Gemco Cable Connector. 5 Pin, 12 Foot Straight Connector for the 955A LDT. Other Lengths and Right Angle Connectors are available |
949019L30 |
Ametek Gemco Cable Connector. 5 Pin, 30 Foot Straight Connector for the 955A LDT. Other Lengths and Right Angle Connectors are available |
949019L6 |
Ametek Gemco Cable Connector. 5 Pin, 6 Foot Straight Connector for the 955A LDT. Other Lengths and Right Angle Connectors are available |
949020L12 |
Ametek Gemco Cable Assembly. 5 Pin, 12 Foot with a Right Angle Cable Connector used with 956A LDT's |
949020L6 |
Ametek Gemco Cable Assembly. 5 Pin, 6 Foot with a Right Angle Cable Connector. For use with 956A LDT |
949023L12 |
Ametek Gemco Cable Assembly for a 955DQ & 956DQ LDT. 12 Pin Straight Connector for option ''E'' Euro Connector, 12 mm, by 12 Feet Long . Other lengths available add $ 2.00 per foot and change the last 2 digits of the part number |
949023L25 |
Ametek Gemco Cable Assembly for a 955DQ & 956DQ LDT. 12 Pin Straight Connector for option ''E'' Euro Connector, 12 mm, by 25 Feet Long . Other lengths available add or subtract $ 2.00 per foot and change the last 2 digits of the part number |
950-1510 |
Ametek Gemco 951A Linear Distance Transducer 951A with a 31.9 Inch Stroke & a 950 Mill Duty Housing 1/8 |
950-1527 |
951AC10319N2D10.9E LDT $ 883.00 950MD31.89A0B05.9OCXX $ 983.00 2/8 |
950-1586 |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950-1586 an Engineered Part Number 12 Inch Active Stroke Rear Trunion Mount Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly |
9501445-0380 |
Ametek Gemco Linear Distance Transducer Intrinsically Safe LDT is UL Listed for Class 1, Groups C & D; Class II, Groups E, F & G; and Class III, Hazardous Locations, when properly installed 0605 = 60.5 Inches of Stroke Cable Assembly with a Straight Connector 04521210 by 6 Foot Long is included |
9501445-0605 |
Ametek Gemco Linear Distance Transducer Intrinsically Safe LDT is UL Listed for Class 1, Groups C & D; Class II, Groups E, F & G; and Class III, Hazardous Locations, when properly installed 0605 = 60.5 Inches of Stroke Cable Assembly with a Straight Connector 04521210 by 6 Foot Long is included
|
9501446-115-0380 |
Ametek Gemco Analog Transceiver for a 9501445 Linear Distance Transducer 115 = 115 VDC Input Power 0380 = 38 Inch Stroke |
9501446-115-0605 |
Ametek Gemco Analog Transceiver for a 9501445 Linear Distance Transducer 115 = 115 VDC Input Power 0605 = 60.5 Inch Stroke |
9501446-230-0605 |
Ametek Gemco Analog Transceiver for a 9501445 Linear Distance Transducer 230 = 230 VDC Input Power 0605 = 60.5 Inch Stroke |
9501446-24-0605 |
Ametek Gemco Analog Transceiver for a 9501445 Linear Distance Transducer 24 = 24 VDC Input Power 0605 = 60.5 Inch Stroke |
950MD-11A-0B-0C-X-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-11A-0B-0C-X-X 11A = 11 Inch Active Stroke 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting X = No other options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-14A-0B-0C-C2-R |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-14A-0B-0C-C2-R 14A = Active stroke in Inches 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches C2 = MS Style Connector and Mate on Side of Housing R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-16A-0B-0C-X-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-16A-0B-0C-X-X 16A = 16 Inch Active Stroke 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting X = No other options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-18A-0B-0C-X-R |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-18A-0B-0C-C-R 18A = Active stroke in Inches 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch |
950MD-18A-0B-0C-X-RF |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-18A-0B-X-RF 18A = Active stroke in Inches 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting RF = Front & Rear Mount Spherical Rod Ends have been specified. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 3/4 Inch Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications |
950MD-20A-0B-0C-X-R |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-20A-0B-0C-X-R 20A = 20 Inch Active Stroke 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch |
950MD-23A-18.4B-0C-X-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-23A-18.4B-0C-X-X 36A = 23 Inch Active Stroke 18.4B = 18.4 Inches of Overstroke / Fully Retracted Overstroke in Inches 0C = 5 Inches Overstroke / Fully Extended Overstroke in Inches X= Standard 1/2 Inch NPT Conduit Fitting X = No other options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. A rear Trunion Mount is provided for mounting either directly in front of the head Assembly or on the rear of the head. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-24A-0.5B-0.5C-C2-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-24A-0.5B-0.5C-C2-X 24A = 24 Inch Active Stroke 0.5B = 0.5 Inches of Overstroke / Fully Retracted Overstroke in Inches 0.5C = 0.5 Inches Overstroke / Fully Extended Overstroke in Inches C2 = MS Style Connector and Mate on the Side of the Housing, 951 & 952 X = No other options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch. The head contains 2, plugged air purge ports for additional cooling if required |
950MD-24A-0B-0C-X-F |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-24A-0B-0C-X-F 24A = 24 Inch Active Stroke 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting F = Front Mount Spherical Rod End 3/4 Inch with Mounting Bolt Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 3/4 Inch |
950MD-30A-0B-0C-X-B1 |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-30A-0B-0C-X-B1 30A = 46 Inch Active Stroke 0B = 0 None 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 None 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting B1 = Protective Boot - Neoprene Coated Nylon - 60 to 250 Degrees F Protects the LDT for resistance to water and oil. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. A rear Trunnion Mount is provided for mounting either directly in front of the head assembly or on the rear of the head. The front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-30A-0B-0C-X-B3 |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-30A-0B-0C-X-B3 30A = 30 Inch Active Stroke 0B = 0 None 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 None 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting B3 = Protective Boot - Teflon Coated Fiberglass Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. A rear Trunnion Mount is provided for mounting either directly in front of the head Assembly or on the rear of the head. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees (23LBS) |
950MD-32A-2B-2C-X-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-32A-2B-2C-X-X 32A = 32 Inch Active Stroke 2B = 2 Overstroke / Fully Retracted Overstroke in Inches 2C = 2 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting X = No other mounting options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. A rear Trunnion Mount is provided for mounting either directly in front of the head Assembly or on the rear of the head. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-33A-1B-1C-C2-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-33A-1B-1C-C2-X 33A = Active stroke in Inches 1B = 1 Inch Fully Retracted Overstroke in Inches 1C = 1 Inch Fully Extended Overstroke in Inches C2 = MS Style Connector and mate on Side of Housing (951 & 952 LDT's only) X = No Mounting or Extreme Condition Options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications |
950MD-34A-0B-0C-X-F |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-24A-0B-0C-X-F 34A = 34 Inch Active Stroke 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting F = Front Mount Spherical Rod End 3/4 Inch with Mounting Bolt Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees. The Front mount also has a Spherical Rod End by 3/4 Inch |
950MD-36A-0B-0C-C-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-36A-0B-0C-C-X 36A = 36 Inch Active Stroke 0B = 0 Inches of Overstroke / Fully Retracted Overstroke in Inches 0C = 0.5 Inches Overstroke / Fully Extended Overstroke in Inches C = MS Style Connector and Mate on the Side of the Housing, for old 950 LDT X = No other options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. A rear Trunnion Mount is provided for mounting either directly in front of the head Assembly or on the rear of the head. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-36A-0B-0C-C2-R |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-36A-0B-0C-C2-R 36A = 36 Inch Active Stroke 0B = 0 Inches of Overstroke / Fully Retracted Overstroke in Inches 0C = 0.5 Inches Overstroke / Fully Extended Overstroke in Inches C2 = MS Style Connector and Mate on Side of Housing R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications.The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-36A-0B-0C-X-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-36A-0B-0C-X-X 36A = 36 Inch Active Stroke 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting X = No other mounting options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-45A-0B-0C-X-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-45A-0B-0C-X-X 45A = 45 Inch Active Stroke 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting X = No other mounting options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-46A-0B-0C-X-B1 |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-46A-0B-0C-X-B1 46A = 46 Inch Active Stroke 0B = 0 None 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 None 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting B1 = Protective Boot - Neoprene Coated Nylon - 60 to 250 Degrees F Protects the LDT for resistance to water and oil. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. A rear Trunnion Mount is provided for mounting either directly in front of the head assembly or on the rear of the head. The front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
|
950MD-46A-0B-0C-X-R |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-46A-0B-0C-X-R 46A = Active stroke in Inches 46'' 0B = 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch |
950MD-60A-0B-0C-X-B1 |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-60A-0B-0C-X-B1 60A = 60 Inch Active Stroke 0B = 0 None 0 Overstroke / Fully Retracted Overstroke in Inches 0C = 0 None 0 Overstroke / Fully Extended Overstroke in Inches X = Standard 1/2 Inch NPT Conduit Fitting B1 = Protective Boot - Neoprene Coated Nylon - 60 to 250 Degrees F Protects the LDT for resistance to water and oil. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. A rear Trunnion Mount is provided for mounting either directly in front of the head assembly or on the rear of the head. The front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees |
950MD-665A-0B-0C-C2-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-665A-0B-0C-C2-X 665A = 66.5 Inches of Active Stroke 0B = 0 Inch Fully Retracted Overstroke 0C = 0 Inch Fully Extended Overstroke C2 = MS Style Connector and mate on Side of Housing (951 & 952 LDT's only) X = No Mounting or Extreme Condition Options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications |
950MD-7A-0B-0C-C2-X |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-7A-0B-0C-C2-X 24A = 24 Inch Active Stroke 0B = 0 Inches of Overstroke / Fully Retracted Overstroke in Inches 0C = 0.5 Inches Overstroke / Fully Extended Overstroke in Inches C2 = MS Style Connector and Mate on the Side of the Housing, 951 & 952 X = No other options Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch. The head contains 2, plugged air purge ports for additional cooling if required |
950MD-84A-0B-0C-X-R |
Ametek Gemco Mill Duty Housing for Linear Displacement Transducers Model 950MD-84A-0B-0C-X-R 84A = 84 Inches of Active Stroke 0B = 0 Inch Fully Retracted Overstroke 0C = 0 Inch Fully Extended Overstroke X = Standard 1/2 Inch conduit Fitting R = Rear Mount Spherical Rod end 3/4 inch with Mounting Bolt Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications |
951-1547 |
Ametek Gemco Linear Displacement Transducer. Quik-Stik II Engineered part number 951VP = Variable Pulse 3.2 Inch Stroke Length 2.7 Inch Dead Band E = External Interrogation E = Environmental MS Connector Special Settings: Function 2, Wire Speed X 4 & Function F, Disable Fault Output Pre- programmed by Ametek (3LBS) similar to a 951VP-0032-X-D2.7EE except with special settings to multiply wire speed x 4, and disable the fault output |
9511405 |
Ametek Gemco Programmer & PC Interface. Hand Held Programmer for Series 951 Quik-Stik II LDT Analog Units. Programs voltage type, span, polarity, zero reference and velocity with ASCII characters which are used to represent each function. Programmer interfaces with the LTD through a small phone jack connection attached to the end of the LDT cable. Operates off of a 9 volt battery which is included along with all cables and hardware to interface one LDT |
9511465 |
Ametek Gemco Linear Displacement Transducer. 4 inch stroke. 0 - 10 Volt DC Output with velocity set at 2.5 Inches / Second. 2 weeks to ship. |
951A-C1-0040-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0040-X-X-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0040 = 4 Inch Stroke Length X = Standard 1.5 Inch Null X = Standard 2.25 Inch Dead Zone E = Environmental MS connector (mating connector and / or pigtail must be ordered separately |
951A-C1-0050-N2-D2-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0050-N2-D2-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0050 = 5 Inch Stroke Length N2 = 2 Null Zone D2 = 2 Inch Dead Zone E = Environmental MS Connector |
951A-C1-0060-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0060-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0060 = 6 Inch Stroke Length N2 = 2 Inch Null over the STANDARD 1.5 Inches D5 = 5 Inch Dead Zone over the STANDARD 2.25 Inches E = Environmental MS Connector |
951A-C1-0060-N3-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0060-N3-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0060 = 6 Inch Stroke Length N3 = 3 Null Zone D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-C1-0070-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0070-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0070 = 7 Inch Stroke Length N2 = 2 Inch Null Zone D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-C1-0088-N2-D5-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0088-N2-D5-C12 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0088 = 8.8 Inch Stroke Length N2 = 2 Inch Null Zone over 1.5 Inches D5 = Non Standard Dead Zone over 2.25 Inches C12 = Potted Pigtail Assembly by 12 Feet |
951A-C1-0098-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0098-X-X-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0098 = 9.8 Inch Stroke Length X = Standard 1.5 Inch Null X = Standard 2.25 Inch Dead Zone E = Environmental MS connector (mating connector and / or pigtail must be ordered separately |
951A-C1-0183-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0183-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0183 = 18.3 Inch Stroke Length N2 = 2'' Null over 1.5 Inches D5 = 5'' Dead Zone over 2.25 Inches E = Environmental MS Connector |
951A-C1-0210-X-X-C15 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0210-X-X-C15 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0210 = 21.0 Inch Stroke Length X = Standard 1.5 Inch Null X = Standard 2.25 Inch Dead Zone C15 = Potted Pigtail Assembly by 15 Feet |
951A-C1-0220-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0220-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0220 = 22.0 Inch Stroke Length N2 = 2 Inch Null Zone D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-C1-0240-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0240-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0240 = 24.0 Inch Stroke Length N2 = 2 Inch Null Zone D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-C1-0321-N2-X-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0321-N2-X-C12 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0321 = 32.1 Inch Stroke Length N2 = 2 Inch Null Zone over 1.5 Inches X = Standard Dead Zone of 2.25 Inches C12 = Potted Pigtail Assembly by 12 Feet |
951A-C1-0330-N3-D6-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0330-N3-D6-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0330 = 33 Inch Stroke Length N3 = 3 Null over 1.5 Inches D6 = Dead Zone over 2.25 Inches E = Environmental MS Connector |
951A-C1-0360-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0360-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0360 = 36 Inch Stroke Length N2 = 2 Inch Null Zone D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-C1-0384-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0384-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0384 = 38.4 Inch Stroke Length N2 = 2'' Null over 1.5 Inches D5 = 5 '' Dead Zone over 2.25 Inches E = Environmental MS Connector |
951A-C1-0450-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0450-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0450 = 45 Inch Stroke Length N2 = 2 Inch Null Zone D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-C1-0460-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0460-X-X-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0460 = 46 Inch Stroke Length X = Standard 1.5 Inch Null X = Standard 2.25 Inch Dead Zone E = Environmental MS connector (mating connector and / or pigtail must be ordered separately |
951A-C1-0493-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0493-N2-D5-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 0493 = 49.3 Inch Stroke Length N2 = 2 Inch Null Zone D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-C1-1320-X-X-C10 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-1320-X-X-C10 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 1320 = 132 Inch Stroke Length X = Standard 1.5 Inch Null X = Standard 2.25 Inch Dead Zone C10 = Potted Pigtail Assembly by 10 Feet |
951A-C1-2335-N3.3-D2-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-2335-N3.3-X-E 951A = Analog Style C1 = 4 to 20 mA Grounded (Sourcing) 233.5 = 233 & 1/2 Inch Stroke Length N3.3 = 3.3 Inch Null Zone X = Standard Dead Zone of 2 .25 Inches E = Environmental MS Connector |
951A-V-0010-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0040-X-X-E 951A = Voltage 0040 = 4 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951A-V-0040-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0040-X-X-E 951A = Voltage 0040 = 4 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951A-V-0042-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0042-X-X-E 951A = Voltage 0042 = 4.20 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951A-V-0060-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0060-X-X-E 951A = Voltage 0060 = 6 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951A-V-0070-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0150-N2-D5-E 951A = Voltage 0070 = 7 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0080-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0040-X-X-E 951A = Voltage 0080 = 8 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951A-V-0100-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0100-X-X-E 951A = Voltage 0100 = 10 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector (4LBS) |
951A-V-0110-N2-D5-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0110-N2-D5-C12 951A = Analog LDT V = Voltage Outputs 0110 = 11 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone C12 = Potted Pigtail cable Assembly by 12 Feet Long |
951A-V-0120-X-X-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0120-X-X-C12 951A = Voltage 0120 = 12 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches C12 = Potted Pigtail Assembly by 12 FT |
951A-V-0140-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0140-N2-D5-E 951A = Voltage 0140 = 14 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0140-X-X-C-12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0140-X-X-C15 951A = Voltage 0140 = 14 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches C15 = Potted Pigtail Assembly by 15 FT |
951A-V-0140-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0140-X-X-E 951A = Voltage 0140 = 14 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector (4LBS) |
951A-V-0150-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0150-N2-D5-E 951A = Voltage 0150 = 15 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0160-N2-D5-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0160-N2-D5-C12 951A = Analog LDT V = Voltage Outputs 0160 = 16 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone C12 = Potted Pigtail cable Assembly by 12 Feet Long |
951A-V-0180-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0180-N2-D5-E 951A = Voltage 0180 = 18 Inch Stroke Length N2 = 3.5 Inch Null Length D5 = 7.25 Inch Dead Zone E = Environmental MS Connector |
951A-V-0200-X-X-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0200-X-X-C12 951A = Voltage 0200 = 20 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches C12 = Potted Pigtail Assembly by 12 FT |
951A-V-0220-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0220-N2-D5-E 951A = Voltage 0220 = 22 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector (6LBS) |
951A-V-0230-N18.4-D5-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0230-N18.4-D5-C12 951A = Voltage 0230 = 23 Inch Stroke Length N18.4 = 18.4 Inch Null Length D5 = 5 Inch Dead Band C12 = Potted Pigtail Assembly |
951A-V-0230-N18.4-X-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0230-N18.4-X-C12 951A = Voltage 0230 = 23 Inch Stroke Length N18.4 = 18.4 Inch Null Length X = Standard Dead Zone of 2.25 Inches C12 = Potted Pigtail Assembly |
951A-V-0240-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0240-N2-D5-E 951A = Voltage 0240 = 24 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0240-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0240-X-X-E 951A = Voltage 0240 = 24 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951A-V-0250-X-X-C15 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0250-X-X-C15 951A = Voltage 0250 = 25 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches C15 = Potted Pigtail Assembly by 15 FT |
951A-V-0278-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0278-X-X-E 951A = Voltage 0278 = 27.8 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector (6LBS) |
951A-V-0300-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0300-X-X-E 951A = Voltage 0300 = 30 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951A-V-0315-N2-D5-C6 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0315-N2-D5-C6 951A = Analog LDT V = Voltage Outputs 0315 = 31.5 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone C6 = Potted Pigtail Assembly by 6 feet long (7LBS) |
951A-V-0315-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0315-N2-D5-E 951A = Voltage 0315 = 31.5 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0320-N3.5-X-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0320-N3-D5-C12 951A = Voltage Output 0320 = 32 Inch Stroke Length N3 = 3 Inch Null Zonel Length D5 = 5 Inch Dead Zone Lenght C12 = 12 Foot Potted Pigtail Assembly |
951A-V-0321-N2-X-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0321-N2-X-C12 951A = Analog LDT V = Voltage Outputs 0321 = 32.1 Inch Stroke Length N2 = 2 Inch Null Length X = Standard Dead Zone of 2.25 Inches C12 = Potted Pigtail cable Assembly by 12 Feet Long |
951A-V-0340-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0340-N2-D5-E 951A = Voltage Output 0340 = 34 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0360-N2-D5-C12 |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0360-N2-D5-C12 951A = Analog LDT V = Voltage Outputs 0360 = 36 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone C12 = Potted Pigtail cable Assembly by 12 Feet Long |
951A-V-0360-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0360-N2-D5-E 951A = Voltage 0360 = 36 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0365-X-X-E |
Ametek Gemco 951A-V-0365-X-X-E Quik-Stik II, Linear Actuator, 0 to +10 VDC |
951A-V-0490-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0490-N2-D5-E 951A = Voltage 0490 = 49 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0490-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0490-X-X-E 951A = Voltage 0490 = 49 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951A-V-0665-N2-D5-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0665-N2-D5-E 951A = Voltage 0665 = 66.5 Inch Stroke Length N2 = 2 Inch Null Length D5 = 5 Inch Dead Zone E = Environmental MS Connector |
951A-V-0900-X-X-C10 |
Ametek Gemco Linear Displacement Transducer. Series Quik-Stik II Model 951A-V-090-X-X-C10 951A = Voltage 0900 = 90 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches C10 = Potted Pigtail Assembly by 10 Foot |
951A-V-0900-X-X-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0900-X-X-E 951A = Voltage 0900 = 90 Inch Stroke Length X = Standard 1.5 Inch Null Length X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951CP-0040-X-X-C100 |
Ametek Gemco Linear Displacement Transducer model 951CP-0040-X-X-C100 Quik-Stik II CP = Control Pulse Version, generates digital outputs over a RS422 Line This LDT is used with Gemco series 1989DL, 2120L1, 1996 & 1746L products 0040 = 4 Inch Stroke X = Standard 1.5 inch Null Zone X = Standard Dead Zone of 2.25 Inches C100 = Potted PigTail Assembly by 100 Feet Long |
951CP-0180-X-X-C100 |
Ametek Gemco Linear Displacement Transducer model 951CP-0180-X-X-C6 Quik-Stik II CP = Control Pulse Version, generates digital outputs over a RS422 Line This LDT is used with Gemco series 1989DL, 2120L1, 1996 & 1746L products 0180 = 18 Inch Stroke X = Standard 1.5 inch Null Zone X = Standard Dead Zone of 2.25 Inches C6 = Potted PigTail Assembly by 6 Feet Long |
951CP-0268-N2-D5-E |
Ametek Gemco Linear Displacement Transducer model 951CP-0268-N2-D5-E Quik-Stik II CP = Control Pulse Version, generates digital outputs over a RS422 Line This LDT is used with Gemco series 1989DL, 2120L1, 1996 & 1746L products 0268 = 26.8 Inch Stroke N2 = 2 Inch Null Zone D5 = 5 Inch Dead Band E = Environmental MS Connector |
951CP-0268-X-X-E |
Ametek Gemco Linear Displacement Transducer model 951CP-0268-X-X-E Quik-Stik II CP = Control Pulse Version, generates digital outputs over a RS422 Line This LDT is used with Gemco series 1989DL, 2120L1, 1996 & 1746L products 0268 = 26.8 Inch Stroke X = Standard 1.5 inch Null Zone X = Standard Dead Zone of 2.25 Inches E = Environmental MS Connector |
951CP-1996-12 |
Ametek Gemco Linear Displacement Transducer. This probe has an Active Travel of .1 to 12 Inches (5LBS) |
951VP-0120-X-X-I-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951VP-0120-X-X-I-E 951VP = Variable Pulse 0120 = 12 Inch Stroke Length X = Standard 1.5 Inch Null Length I = Internal Interrogation E = Environmental MS Connector |
951VP-0199-X-X-I-E |
Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951VP-0199-X-X-I-E 951VP = Variable Pulse 0199 = 19.9 Inch Stroke Length X = Standard 1.5 Inch Null Length X - Standard Dead Zone of 2.25 Inches I = Internal Interrogation E = Environmental MS Connector |
951VP-1992-12 |
Ametek Gemco Linear Distance Transducer / LDT for use with the 1992 Press-Set Press Automation Controller 12 Inch Stroke Length (ram adjust mechanism in inches) |
951VP-1992-33 |
Ametek Gemco Linear Distance Transducer / LDT for use with the 1992 Press-Set Press Automation Controller 33 Inch Stroke Length (ram adjust mechanism in inches) |
952-1460240 |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 952-1460240 952QD = Quadrature Version 24 Inch Stroke RES 1000 with special filter routine FORD Motor
|
952A-C4-0015-X-X-T |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 925A-C4-0015-X-X-T 952A = Analog Output C4 = Voltage Output 4 - 20 mA 0015 = Stroke 1.5 Inch X = Standard 2.0 Inch Null X = Standard Dead Zone 2.5 Inch T = Threaded Metal Connector, fits MTS RBon Tempo II or III |
952A-C4-0180-X-D5-C6 |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 925A-C4-0180-X-D5-C6 952A = Analog Output C4 = Voltage Output 4 - 20 mA 0180 = Stroke 18 Inch X = Standard 2.0 Inch Null D5 = Dead Zone 5 Inch C6 = Potted Pigtail Assembly by 6 Foot |
952A-C4-0180-X-X-C6 |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 925A-C4-0180-X-X-C6 952A = Analog Output C4 = Voltage Output 4 - 20 mA 0180 = Stroke 18 Inch X = Standard 2.0 Inch Null X = Standard 2.5 Inch Dead Band C6 = Potted Pigtail Assembly by 6 Foot |
952A-C4-0200-X-D5-E |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx 952A = Analog Output C4 = Voltage Output 4 - 20 mA 0200 = Stroke 20 Inch X = Standard 1.5 Inch Null D5 = Dead Zone 5 Inch E = Environmental MS Connector. (mating connector is ordered separately) |
952A-C4-0200-X-D5-S |
Ametek Gemco S = Standard 12 mm 5 Pin Euro Connector (CE Approved) Mating Connector and or Pigtails are ordered separately |
952A-C4-0200-X-X-E |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 925A-C4-0200-X-X-E 952A = Analog Output C4 = Voltage Output 4 - 20 mA 0200 = Stroke 20 Inch X = Standard 2.0 Inch Null X = Standard Dead Zone 2.5 Inch E = Environmental MS Connector (mating connector or pigtail must be ordered separately) |
952A-C4-0230-X-X-E |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 925A-C4-0230-X-X-E 952A = Analog Output C4 = Voltage Output 4 - 20 mA 0230 = Stroke 23 Inch X = Standard 2.0 Inch Null X = Standard Dead Zone 2.5 Inch E = Environmental MS Connector (mating connector or pigtail must be ordered separately) |
952A-C4-0360-X-X-S |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 925A-C4-0360-X-X-S 952A = Analog Output C4 = Voltage Output 4 - 20 mA 0360 = Stroke 36 Inch X = Standard 2.0 Inch Null X = Standard Dead Zone 2.5 Inch S = Standard Connector. 12 mm 5 Pin Euro connector. Mating connector 949-019 or 949-020 and or pigtail must be ordered separately |
952A-C4-066-X-X-S |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 925A-C4-0660-X-X-S 952A = Analog Output C4 = Voltage Output 4 - 20 mA 0660 = Stroke 66 Inch X = Standard 2.0 Inch Null X = Standard Dead Zone 2.5 Inch S = Standard Connector. 12 mm 5 Pin Euro connector. Mating connector 949-019 or 949-020 and or pigtail must be ordered separately |
952A-V0-0010-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V0-0010-X-X-S ''Blue Ox'' A = Analog Version V0 = Voltage Output 0 - 10 VDC 0010 = 1 Inch Stroke / Active Travel X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) |
952A-V0-0100-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V0-0100-X-X-S ''Blue Ox'' A = Analog Version V0 = Voltage Output 0 - 10 VDC 0100 = 10 Inch Stroke / Active Travel X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) |
952A-V0-0200-X-D5-E |
Ametek Gemco Linear Displacement Transducer model 952A-V0-0200-X-D5-S ''Blue Ox'' A = Analog Version V0 = Voltage Output 0 - 10 VDC 0180 = 18 Inch Stroke X = Standard Null Zone of 2 Inches D5 = Dead Zone of 5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6 |
952A-V0-0205-X-X-T |
Ametek Gemco Linear Displacement Transducer model 952A-V0-0205-X-X-T ''Blue Ox'' A = Analog Version V0 = Voltage Output 0 - 10 VDC 0205 = 20.5 Inch Stroke / Active Travel X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches T = Threaded Metal Connector. Fits MTS RB on Tempo II or III |
952A-V0-0720-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V0-0100-X-X-S ''Blue Ox'' A = Analog Version V0 = Voltage Output 0 - 10 VDC 0720 = 72 Inch Stroke / Active Travel X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) |
952A-V1-0040-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V1-0040-X-X-S ''Blue Ox'' A = Analog Version V1 = 10 to 0 VDC Output 0040 = 4 Inch Stroke X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6 |
952A-V1-0072-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V1-0072-X-X-S ''Blue Ox'' A = Analog Version V1 = 10 to 0 VDC Output 0072 = 7.2 Inch Stroke X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6 |
952A-V1-0120-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V1-0120-X-X-S ''Blue Ox'' A = Analog Version V1 = 10 to 0 VDC Output 0120 = 12 Inch Stroke X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6 |
952A-V1-0180-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V1-0180-X-X-S ''Blue Ox'' A = Analog Version V1 = 10 to 0 VDC Output 0180 = 18 Inch Stroke X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector,mating connector 949-019 or 949-020 and or pigtail must be ordered separately (5LBS) 1/6 |
952A-V1-0330-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V1-0330-X-X-S ''Blue Ox'' A = Analog Version V1 = 10 to 0 VDC Output 0330 = 33 Inch Stroke X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6 |
952A-V1-0400-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V1-0040-X-X-S ''Blue Ox'' A = Analog Version V1 = 10 to 0 VDC Output 0400 = 40 Inch Stroke X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6 |
952A-V1-0810-X-X-S |
Ametek Gemco Linear Displacement Transducer model 952A-V1-0810-X-X-S ''Blue Ox'' A = Analog Version V1 = 10 to 0 VDC Output 0810 = 81 Inch Stroke X = Standard Null Zone of 2 Inches X = Standard Dead Zone of 2.5 Inches S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6 |
952CP-0040-X-X-E |
Ametek Gemco Linear Distance Transducer 952CP = BlueOx Control Pulse Version / Digital Output 0040 = 4 Inch Stroke Length X = Standard 2 Inch Null Length X = Standard Dead Zone Length 2 & 1/2 Inches E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately) |
952CP-0080-X-X-E |
Ametek Gemco Linear Distance Transducer 952CP = BlueOx Control Pulse Version / Digital Output 0080 = 8 Inch Stroke Length X = Standard 2 Inch Null Length X = Standard Dead Zone Length 2.5 Inches E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately) |
952CP-0120-X-X-E |
Ametek Gemco Linear Distance Transducer 952CP = BlueOx Control Pulse Version / Digital Output 0120 = 12 Inch Stroke Length X = Standard 2 Inch Null Length X = Standard Dead Zone Length 2 & 1/2 Inches E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately) |
952CP-0267-N2-D5-E |
Ametek Gemco Linear Distance Transducer model AME-952CP-0267-N2-D5-E 952CP = BlueOx Control Pulse Version / Digital Output 0267 = 26.7 Inch Stroke Length N2 = 2 Inch Null Length (Standard) D5 = 5 Inch Dead Zone E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately) |
952CP-0325-X-D5-E |
Ametek Gemco Linear Distance Transducer 952CP = BlueOx Control Pulse Version / Digital Output 0325 = 32.5 Stroke Length X = Standard 2 Inch Null Length D5 = Dead Zone Length 5 Inches E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately) |
952QD-0100-X-X-C6-1000-EF4- |
Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx Model 952QD-0100-X-X-C6-1000-EF4-M1-N-X 952QD = Quadrature Version 0100 = 10 Inch Stroke X = Standard 2.0 Inch Null X = Standard 2.5 Inch Dead Zone C6 = Potted Pigtail Assembly by 6 Foot long 1000 = Standard Output Resolution, Cycles per inch E = Input type '' Sinking'' (typically used with sourcing output type) F4 = 75 KHz Quadrature Cycle Output Frequency Range M1 = X1 Quadrature. Output Mode D = Differntial RS422 Line Driver. TTL compatible X = no other options |
952RS-0030-X-X-C6 |
Ametek Gemco Linear Displacement Transducer 952RS-0030-X-X-C6 952RS =Digital Version - Start/Stop Pulse 0030 = 3 Inch Stroke Length X = Standard Null Length of 2 Inches X = Standard Dead Zone of 2 Inches C6 = Potted Pigtail Cable assembly by 6 feet long |
952RS-0120-X-X-E |
Ametek Gemco Linear Displacement Transducer 952RS-0120-X-X-E 952RS =Digital Version - Start/Stop Pulse 0120 = 12 Inch Stroke Length X = Standard Null Length of 2 Inches X = Standard Dead Zone of 2 Inches E = Environmental MS Connector. Mating connector and / or pigtail must be ordered separately |
952RS-0180-X-X-C6 |
Ametek Gemco Linear Displacement Transducer 952RS-0180-X-X-C6 952RS =Digital Version - Start/Stop Pulse 0180 = 18 Inch Stroke Length X = Standard Null Length of 2 Inches X = Standard Dead Zone of 2 Inches C6 = Potted Pigtail Cable assembly by 6 feet long |
952RS-0360-X-X-E |
Ametek Gemco Linear Displacement Transducer 952RS-0360-X-X-E 952RS =Digital Version - Start/Stop Pulse 0360 = 36 Inch Stroke Length X = Standard Null Length of 2 Inches X = Standard Dead Zone of 2 Inches E = Environmental MS Connector. Mating connector and / or pigtail must be ordered separately |
952VP-0240-X-X-E-E-002 |
Ametek Gemco Linear Displacement Transducer model 952VP-0300-X-X-E-E-002 ''Blue Ox'' VP = Variable Pulse 0300 = 30 Inch Stroke X = Standard 2 Inch Null Zone X = Standard 2.5 Inch Dead Zone E = Environmental MS Connector, Designation T is no longer available E = External Interrogation 002 - Number of Recirculations |
952VP-0300-X-X-E-E-002 |
Ametek Gemco Linear Displacement Transducer model 952VP-0300-X-X-E-E-002 ''Blue Ox'' VP = Variable Pulse 0300 = 30 Inch Stroke X = Standard 2 Inch Null Zone X = Standard 2.5 Inch Dead Zone E = Environmental MS Connector, Designation T is no longer available E = External Interrogation 002 - Number of Recirculations |
952VP-0660-X-X-E-I-001 |
Ametek Gemco Linear Displacement Transducer model 952VP-0660-X-X-E-I-001 ''Blue Ox'' VP = Variable Pulse 0660 = 66 Inch Stroke X = Standard 2 Inch Null Zone X = Standard 2.5 Inch Dead Zone E = Environmental MS Connector I = Internal Interrogation 001 - Number of Recirculations (standard) |
952VP-0710-X-X-E-I-001 |
Ametek Gemco Linear Displacement Transducer model 952VP-0710-X-X-E-I-001 ''Blue Ox'' VP = Variable Pulse 0710 = 71 Inch Stroke X = Standard 2 Inch Null Zone X = Standard 2.5 Inch Dead Zone E = Environmental MS Connector I = Internal Interrogation 001 - Number of Recirculations (standard) |
952VP-0780-X-X-E-E-002 |
Ametek Gemco Linear Displacement Transducer model 952VP-0780-X-X-E-E-002 ''Blue Ox'' VP = Variable Pulse 0780 = 0780 Inch Stroke X = Standard 2 Inch Null Zone X = Standard 2.5 Inch Dead Zone E = Environmental MS Connector, Designation T is no longer available E = External Interrogation 002 - Number of Recirculations |
952VP-0960-N2.5-D5-E-I-001 |
Ametek Gemco Linear Displacement Transducer model 952VP-0960-N2.5-D5-E-I-001 ''Blue Ox'' VP = Variable Pulse 0960 = 96 Inch Stroke N2.5 = 2.5 Inch Null Zone D5 = 5 Inch Dead Zone E = Environmental MS Connector I = Internal Interrogation 001 - Number of Recirculations ( standard)
|
952VP-1560-X-X-E-E-002 |
Ametek Gemco Linear Displacement Transducer model 952VP-1560-X-X-E-E-002 ''Blue Ox'' VP = Variable Pulse 1560 = 1560 Inch Stroke X = Standard 2 Inch Null Zone X = Standard 2.5 Inch Dead Zone E = Environmental MS Connector, Designation T is no longer available E = External Interrogation 002 - Number of Recirculations |
952VP-2110-16 |
Ametek Gemco LDT. BlueOx Variable Pulse LDT for a 2110 Shut Height Monitor. 16 Inch Stroke Length 1/7 |
952VP-21104 |
Ametek Gemco Linear Distance Transducer LDT. Blue Ox Variable Pulse with a 4 Inch Stroke |
952VP0300//0001 |
Ametek Gemco LDT, Blue OX, 30 Inch Stroke, Internal Interrogation, Environmental Connector, 6 Recirculations (6LBS) Sr # 18126-AO |
953A-C4-0070-X-X-S-X |
Ametek Gemco Linear Distance Transducer. (LDT) High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's C4= 4 to 20mA Output 0070 = 7 Inch Active Stroke X = Standard 2 Inch Null Zone X = Standard Dead Band of 2.5 Inches S = 5 Pin Micro, 12 mm Euro, Connector X= No other options |
953A-C4-0118-X-X-S-X |
Ametek Gemco Linear Distance Transducer. (LDT) High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's C4= 4 to 20mA Output 0118 = 11.8 Inches Active Stroke X = Standard 2 Inch Null Zone X = Standard Dead Band of 2.5 Inches S = 5 Pin Micro, 12 mm Euro, Connector X= No other options |
953A-C4-0130-X-X-S-X |
Ametek Gemco Linear Distance Transducer. (LDT) High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's C4= 4 to 20mA Output 0130 = 13 Inches of Active Stroke X = Standard 2 Inch Null Zone X = Standard Dead Band of 2.5 Inches S = 5 Pin Micro, 12 mm Euro, Connector X= No other options |
953A-C4-0300-X-D2.5-S-X |
Ametek Gemco Linear Distance Transducer. (LDT) Model AME-953A-C4-0300-X-D2.5-S-X High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's C4= 4 to 20mA Output 0300 = 30 Inches of Active Stroke X = Standard 2 Inch Null Zone D2.5 = Dead Band of 5 Inches S = 5 Pin Micro, 12 mm Euro, Connector X= No other options |
953A-C4-0460-X-D2.5X-S-X |
Ametek Gemco Linear Distance Transducer. (LDT) Model 953A-C4-0460-X-D2.5-S-X High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's C4= 4 to 20mA Output 0460 = 46 Inches of Active Stroke X = Standard 2 Inch Null Zone D2.5 = Dead Band of 5 Inches S = 5 Pin Micro, 12 mm Euro, Connector X= No other options |
953A-C4-0600-X-D2.5-S-X |
Ametek Gemco Linear Distance Transducer. (LDT) Model 953A-C4-0600-X-D2.5-S-X High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's C4= 4 to 20mA Output 0600 = 60 Inches of Active Stroke X = Standard 2 Inch Null Zone D2.5 = Dead Band of 5 Inches S = 5 Pin Micro, 12 mm Euro, Connector X= No other options |
953A-C4-0700-X-X-S-X |
Ametek Gemco Linear Distance Transducer. (LDT) High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's C4= 4 to 20mA Output 0700 = 70 Inch Active Stroke X = Standard 2 Inch Null Zone X = Standard Dead Band of 2.5 Inches S = 5 Pin Micro, 12 mm Euro, Connector X= No other options |
953A-V0-0060-X-X-M-X |
Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Model 953A-V0-0060-X-X-M-X V0 = 0 to 10 VDC Output 0060 = Stroke 6 Inch Length X = Standard 2.0 Inch Null Zone X = Standard Dead Band 2.5 Inch M = 6 Pin DIN-MTS-D60 compatible option X = No options |
953A-V0-0119-X-D5-C12 |
Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Model 953A-V0-0119-X-D5-C12 V0 = 0 to 10 VDC Output 0119 = Stroke 11.9 Inch Length 300 mm X = Standard 2.0 Inch Null Zone D5= Standard Dead Band 2.5 Inch C12 = Integral Cable / Potted Pigtail by 12 Foot Long |
953A-V0-0180-X-X-C30-X |
Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Model 953A-V0-0180-X-X-C30-X V0 = 0 to 10 VDC Output 0180 = Stroke 18 Inch Length X = Standard 2.0 Inch Null Zone X = Standard Dead Band 2.5 Inch C = Integral Cable Assembly by 30 Feet Long X = No options |
953A-V0-0240-X-X-S-X |
Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Model 953A-V0-0240-X-X-S-X V0 = 0 to 10 VDC Output 0240 = Stroke 24 Inch Length X = Standard 2.0 Inch Null Zone X = Standard Dead Band 2.5 Inch S = 5 Pin Micro, 12 mm Euro Connector X = No options |
953A-V0-0500-X-X-S-X |
Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Model 953A-VO-0500-X-X-M-X VO = 0 to 10 VDC Output 0500 = Stroke 6 Inch Length X = Standard 2.0 Inch Null Zone X = Standard Dead Band 2.5 Inch S = 5 Pin Micro, 12 MM Euro X = No options |
953A-V0-300M-X-D5-C12 |
Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Metric Stroke and Threads M18 x 1.5 metric threads Model 953A-V0-300M-X-D5-C12 V0 = 0 to 10 VDC Output 0300M = 300 mm Stroke Length X = Standard 2.0 Inch Null Zone D5 = Dead Band5 Inches C12 = Integral Cable / Potted Pigtail by 12 Foot Long |
953A-VO-0900-X-C10-X |
Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Model 953A-VO-0900-X-X-C10-X VO = 0 to 10 VDC Output 0900 = Stroke 90 Inch Length X = Standard 2.0 Inch Null Zone X = Standard Dead Band 2.5 Inch C10 = Integral Cable Assembly by 10 Feet Long X = No other options |
953A-VO-2400-X-X-S-X |
Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Model 953A-VO-2400-X-X-S-X VO = 0 to 10 VDC Output 2400 = 240 Inch = 20 Foot Stroke / 20 Foot Active Travel X = Standard 2.0 Inch Null Zone X = Standard Dead Band 2.5 Inch S = 5 Pin Micro, 12 mm Euro Connector X = No options |
953D-RS-0240.X-X-S-X |
Ametek Gemco Linear Distance Transducer model 953D-RS-0240.X-X-S-X. (LDT) High Resolution (Digital) The 953D is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's RS = RS-422 Start/Stop Pulse 0240 = 24 Inch Active Stroke X = Standard 2 Inch Null Zone X = Standard Dead Band of 2.5 Inches S = 5 Pin Micro, 12 mm Euro, Connector X= No other options |
9551409 |
Ametek Gemco Programming Unit. In Line Active Zone Programming Unit |
955A-C4-0120-X |
Ametek Gemco LDT. Series 955A BRIK Gen III is an accurate programmable, auto-tuning, non-contact, Linear Displacement Transducer C4 = 4 to 20 Ma 0120 = 12 Inch Stroke X = No options Null Zone: 3 Inches Dead Zone: 2 Inches Repeatability: + or - 0/006 % of Full Stroke Connector: 5 Pin Micro 12mm Euro IP67 Enclosure CE Approval |
955A-C4-0200-X |
Ametek Gemco LDT. Series 955A BRIK Gen III is an accurate programmable, auto-tuning, non-contact, Linear Displacement Transducer C4 = 4 to 20 Ma 0200 = 20 Inch Stroke X = No options Null Zone: 3 Inches Dead Zone: 2 Inches Repeatability: + or - 0/006 % of Full Stroke Connector: 5 Pin Micro 12mm Euro IP67 Enclosure CE Approval |
955A-C4-0240-X |
Ametek Gemco LDT. Series 955A BRIK Gen III is an accurate programmable, auto-tuning, non-contact, Linear Displacement Transducer C4 = 4 to 20 Ma 0240 = 24 Inch Stroke X = No options Null Zone: 3 Inches Dead Zone: 2 Inches Repeatability: + or - 0/006 % of Full Stroke Connector: 5 Pin Micro 12mm Euro IP67 Enclosure CE Approval |
955A-C4-0300-X |
Ametek Gemco LDT. Series 955A BRIK Gen III is an accurate programmable, auto-tuning, non-contact, Linear Displacement Transducer C4 = 4 to 20 Ma 0300 = 30 Inch Stroke X = No options Null Zone: 3 Inches Dead Zone: 2 Inches Repeatability: + or - 0/006 % of Full Stroke Connector: 5 Pin Micro 12mm Euro IP67 Enclosure CE Approval (6LBS) |
955A-V0-018-X |
Ametek Gemco Linear Displacement Transducer 955A BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal V0 = 0 to 10 Volt DC Output 0180 = 18 Inch Active Travel X = No other options |
955A-V0-0957-E |
Ametek Gemco Linear Displacement Transducer 955A BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal V0 = 0 to 10 Volt DC Output 0957 = 95.7 Inch Active Travel E = IP68 Rated Connector for High Humidity Environments |
955A-V0-0958-E |
Ametek Gemco Linear Displacement Transducer 955A BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal V0 = 0 to 10 Volt DC Output 0958 = 95.8 Inch Active Travel E = IP68 Rated Connector for High Humidity Environments |
955ARM18 |
Ametek Gemco Control Arm by 18 Inches Long. For use with 955A & S, 955DQ & D, 955LC LDT's Female & Male Threaded Ends 1/4-28. Other lengths available @ 3,6,9,12,15,18,22,28'' or a custom length |
955ARM6 |
Ametek Gemco Control Arm by 6 Inches Long. For use with 955A & S, 955DQ & D, 955LC LDT's Female & Male Threaded Ends 1/4-28. Other lengths available @ 3,6,9,12,15,18,22,28'' or a custom lengths |
955D-RS-1060-X |
Ametek Gemco Linear Displacement Transducer model 955D-RS-1600-X ''BRIK Gen III'' Digital Output., RS 422 START/STOP with interrogation Start Sequence 1060 = 160 Inch Stroke
|
955DQ-0060-E-1000-E-F7-X1-N |
Ametek Gemco Linear Distance Transducer model 955DQ-0060-E-1000-E-F7-X1-N-D-X 955DQ = BRIK Generation III with direct Quadrature Output. Auto-Tuning Low Profile Package with LED Diagnostics 0060 = 6 Inch Stroke/ Active Travel E = Euro 12 Pin, 12mm Connector 1000 = 1000 Cycles per Inch Output Resolution. Maximum internal resolution is .001 Inches. Available range is 0001 to 9999 E = Sinking Type, typically used with sourcing output type F7 = 250 KHz Quadrature Cycle Output Frequency Range X1 = X1 Quadrature Output Mode N = Nonvolatile Zero Offset Storage. Retentive 100,000 storage cycles maximum D = Differential RS422 Line Driver X = No Environment options |
955LC-C4-0360 |
Ametek Gemco Linear Displacement Transducer Model 955LC-C4-0360 Series 955LC Smart BRIK Analog LDT C4 = 4 to 20mA Output 36 Inch Stroke Length / Active Travel Absolute position, repeatable to 0.01% of the sensing distance Quick Disconnect Connector |
955LC-VO-0200 |
Ametek Gemco Linear Displacement Transducer Model 955LC-VO-0200 Series 955LC Smart BRIK Analog LDT VO = 0 to 10 Volt DC Output 0200 = 20 Inch Stroke Length / Active Travel Absolute position, repeatable to 0.01% of the sensing distance Quick Disconnect Connector |
955LC-VO-0360 |
Ametek Gemco Linear Displacement Transducer Model 955LC-VO-0360 Series 955LC Smart BRIK Analog LDT VO = 0 to 10 Volt DC Output 36 Inch Stroke Length / Active Travel Absolute position, repeatable to 0.01% of the sensing distance Quick Disconnect Connector |
955S-C4-0070 |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal C4 = 4 to 20 mA Output 0070 = 7 Inch Active Travel |
955S-C4-0100 |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal C4 = 4 to 20 mA Output 0100 = 10 Inch Active Travel |
955S-C4-0130 |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal C4 = 4 to 20 mA Output 0130 = 13 Inch Active Travel |
955S-C4-0180 |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal C4 = 4 to 20 mA Output 0180 = 18 Inch Active Travel |
955S-C4-0500 |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal C4 = 4 to 20 mA Output 0500 = 50 Inch Active Travel |
955S-C4-0510 |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal C4 = 4 to 20 mA Output 0510 = 51 Inch Active Travel |
955S-V0-0540 |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal VO = 0 to 10 Volt DC Output 0540 = 54 Inch Active Travel
|
955S-V0-0650 |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal VO = 0 to 10 Volt DC Output 0650 = 65 Inch Active Travel
|
955S-V0-0820-E |
Ametek Gemco Linear Displacement Transducer 955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal V0 = 0 to 10 Volt DC Output 0820 = 82 Inch Active Travel E = IP68 Rated Connector for High Humidity Environments |
956A-C4-0090-E |
Ametek Gemco Linear Displacement Transducer Model 956A-C4-0090-E 956A = BLOK LDT Analog Version C4 = 4 to 20mA Output 0090 = 9 Inch Active Stroke E = Wet Environment. Electronics sealed to a IP 68 Rating Input Voltage 13.5 to 30 VDC Null Zone 3 Inch Dead Zone 2 Inch 3 Diagnostic LED's Standard 5 Pin Micro 12mm Euro Connector CE Approval IP68 Enclosure -20 to 70 Degree C |
956A-C4-0130-X |
Ametek Gemco Linear Displacement Transducer Model 956A-C4-0130-X 956A = BLOK LDT Analog Version C4 = 4 to 20mA Output 0130 = 13 Inch Active Stroke X = No other options Input Voltage 13.5 to 30 VDC Null Zone 3 Inch Dead Zone 2 Inch 3 Diagnostic LED's Standard 5 Pin Micro 12mm Euro Connector CE Approval IP67 Enclosure -20 to 70 Degree C |
956DQ0120E1000EF7X1NDF |
Ametek Gemco LDT 956DG BLOK Digital Quadrature Output with resolutions up to 9,999 Cycles per Inch 956DQ-0120-E-1000-E-F7-X1-N-D-F 0120 = 12 Inch Stroke Length E = Euro 12 Pin, 12 mm Connector 1000 = 1000 Cycles per Inch Output Resolution E = Sinking Input, typically used with sourcing output type F7 = 250 KHz Quadrature Cycle Output Frequency Range X1 = X1 quadrature, 1ms update, output mode N = Non-volatile Aero Output Storage, Retentive 100,000 storage cycles maximum D = Differential RD422 line driver, TTL compatible F = Front Metal Rod End, Female |
956DQ0120E1000EF7X1NDX |
Ametek Gemco LDT 956DG BLOK Digital Quadrature Output with resolutions up to 9,999 Cycles per Inch 956DQ-0120-E-1000-E-F7-X1-N-D-X 0120 = 12 Inch Stroke Length E = Euro 12 Pin, 12 mm Connector 1000 = 1000 Cycles per Inch Output Resolution E = Sinking Input, typically used with sourcing output type F7 = 250 KHz Quadrature Cycle Output Frequency Range X1 = X1 quadrature, 1ms update, output mode N = Non-volatile Aero Output Storage, Retentive 100,000 storage cycles maximum D = Differential RD422 line driver, TTL compatible X = No Options |
956S-VO-0110-E |
Ametek Gemco Linear Distance Transducer 956S Series, Smart BLOK Analog VO = 0 to 10 VDC Output 0110 = 11 Inch Stroke Length E = Electronics Sealed to an IP 68 Rating for Wet Environments |
A/H-ARC 18'' X 4 |
Ametek Gemco Type A/H-ARC Brake System. Includes 4, 18 X 8 Inch Hydraulic Brakes, Hydraulic Actuators, Fluid Reservoir Bleeder, Pre-Assembled Air / Hydraulic Control Panel, 3/4 HP Motor & Compressor, Tubing, Armored Hoses, Fittings and Heavy Duty Brake Fluid. Rated dynamic stopping torque, progressive to 3600 LBS./FT. Specify 230 VDC or 230 / 460 VAC 60 Hz., 3 ph power. Net weight 948 LBS. Prices do not include brake wheels. |
A/H-ARC 2-18 |
Ametek Gemco Type A/H-ARC Brake System. Includes 2, 18 X 8 Inch Hydraulic Brakes, Hydraulic Actuators, Fluid Reservoir Bleeder, Pre-Assembled Air / Hydraulic Control Panel, 3/4 HP Motor & Compressor, Tubing, Armored Hoses, Fittings and Heavy Duty Brake Fluid. Rated dynamic stopping torque, progressive to 3600 LBS./FT. Specify 230 VDC or 230 / 460 VAC 60 Hz., 3 ph power. Net weight 948 LBS. Prices do not include brake wheels. |
A/H-ARC1-14 |
Ametek Gemco Air over Hydraulic, Air Treadle Remote Control Brake System. Qty. 1, 14 Inch Diameter Hydraulic Brake |
A/H-ERC |
Ametek Gemco Type A/H-ERC Conversion System for Type H Systems (no parking feature). Includes one 3/4 HP motor driven compressor assembly, one prepiped and prewired control panel, one two way hydraulic check valve, one installation kit including tubing, fittings and fluid. 230VDC or 460VAC 3PH 60Hz. |
A/H-ERC 18'' X 4 |
Ametek Gemco Type A/H-ERC Brake System, Electric Remote Controlled. Provides Service Braking, Off Power Emergency Braking plus Parking Brakes. Air over hydraulic brake system includes 4, 18 Inch Brake Assemblies, Fluid Reservoir Bleeder, Foot Treadle Valve, Preassembled Air-Over-Hydraulic Control Panel, 3/4 Horsepower Motor & Compressor, Parking Control Switch, Hyd Tubing, Armored Hoses, Fittings & Brake Fluid. 230 VDC or 230 / 460 VAC 60 Hz. Motor controls are in a NEMA 12 enclosure which is mounted on the panel. Panel size 33 Wide X 45 High X 16 Inches Deep. Brake Wheels are not included |
A/H-ERC 18'' X 4 W/PRK |
Ametek Gemco Type A/H-ERC Brake System, Electric Remote Controlled with 4 Brake Parking. Provides Service Braking, Off Power Emergency Braking plus Parking Brakes. Air over hydraulic brake system includes 4, 18 Inch Brake Assemblies, Fluid Reservoir Bleeder, Foot Treadle Valve, Preassembled Air-Over-Hydraulic Control Panel, 3/4 Horsepower Motor & Compressor, Parking Control Switch, Hyd Tubing, Armored Hoses, Fittings & Brake Fluid. 230 VDC or 230 / 460 VAC 60 Hz. Motor controls are in a NEMA 12 enclosure which is mounted on the panel. Panel size 33 Wide X 45 High X 16 Inches Deep. Brake Wheels are not included |
A/H-ERC10-1 |
Ametek Gemco Hydraulic Brake System. Air Over Hydraulic Electric Remote Controlled Single 10 Inch Brake System |
A/H-ERC141 |
Ametek Gemco A/H-ERC System with 1 14 Inch Hydraulic Brake Assembly |
A/HM-ARC 18'' X 2 |
Ametek Gemco Type A/HM-ARC Brake System with Parking. Provides Service Braking, Off Power Emergency Braking plus Parking Brakes. Air over hydraulic brake system includes 2, 18 Inch Brake Assemblies, Fluid Reservoir Bleeder, Foot Treadle Valve, Preassembled Air-Over-Hydraulic Control Panel, 3/4 Horsepower Motor & Compressor, Parking Control Switch, Hyd Tubing, Armored Hoses, Fittings & Brake Fluid. 230 VDC or 230 / 460 VAC 60 Hz. Motor controls are in a NEMA 12 enclosure which is mounted on the panel. Panel size 33 Wide X 45 High X 16 Inches Deep. Brake Wheels are not included |
A/HM-ARC 18'' X 4 |
Ametek Gemco Type A/HM-ARC Brake System with 4 Brake Parking. Provides Service Braking, Off Power Emergency Braking plus Parking Brakes. Air over hydraulic brake system includes 4, 18 Inch Brake Assemblies, Fluid Reservoir Bleeder, Foot Treadle Valve, Preassembled Air-Over-Hydraulic Control Panel, 3/4 Horsepower Motor & Compressor, Parking Control Switch, Hyd Tubing, Armored Hoses, Fittings & Brake Fluid. 230 VDC or 230 / 460 VAC 60 Hz. Motor controls are in a NEMA 12 enclosure which is mounted on the panel. Panel size 33 Wide X 45 High X 16 Inches Deep. Brake Wheels are not included |
A/HM-ERC |
Ametek Gemco Type A/HM-ERC Conversion System for Type HM Systems (with parking feature). Includes one 3/4 HP motor driven compressor assembly, one prepiped and prewired control panel, one two way hydraulic check valve, one installation kit including tubing, fittings and fluid. 230VDC or 460VAC 3PH 60Hz. |
A/HM-ERC System |
Ametek Gemco Type A/HM-ERC System. Qty. 1, 18 X 8 Inch Brake Type HM Brake (with parking brake feature). Includes Brake, Fluid Reservoir Bleeder, Pre-Assembled Air / Hydraulic Control Panel, 3/4 HP Motor Driven Compressor Assembly, Tubing, Hoses, Fittings & Brake Fluid. 230 VDC or 460 VAC 3PH 60Hz Does not require existing brake but does require the existing foot pedal in the crane cab |
A/HM-HRC 18X2 |
Ametek Gemco Air Over Hydraulic Brake System with Parking to provide 3600 FT LBS of Braking Torque, Emergency Braking & 1400 FT LBS of Parking Brake Torque. Includes 2, 18 Inch Brakes, Hydraulic Actuators, Fluid Reservoir Bleeder, Pre-Assembled Air over Hydraulic Panel, 3/4 HP Motor & Compressor, Hydraulic Foot Pedal, Parking Control Switch, Tubing, Hoses, Fittings & Brake Fluid. Brake Wheels are not included. |
A000228 |
Ametek Gemco Valve. Over-Pressure Safety Valve (1LB) CMH000161 |
A000267 |
Ametek Gemco Valve. Air Check Valve, 1 Way (1LB) 1658870 |
A002091 |
Ametek Gemco Drain Valve for Air Tank (1LB) |
A002226 |
Ametek Gemco Air Pressure Gauge, Back Connection (<1LB) |
A0054300 |
Ametek Gemco Switch for a Series 1025 Switch Assembly |
A0054700 |
Ametek Gemco Button. Button on a 1025D Foot or Palm Operated Switch Assembly. 1 LB Gross |
A021857 |
Ametek Gemco OBSOLETE Moisture Ejection Valve, no longer manufactured. No parts or repair kits are available. Replaced by J107084 (2LBS) |
A024912 |
Ametek Gemco Protection Valve |
A032922 |
Ametek Gemco 2 Way Air Check Valve (<1LB) CMQ000207 |
A035780 |
Ametek Gemco Single Air Reservoir |
A037051 |
Ametek Gemco Copper Tubing, 50 Ft 5/16 Inch |
A039206 |
Ametek Gemco RF Valve Seal Kit (1LB) |
A039221 |
Ametek Gemco RG Valve Seal Kit |
A045240 |
Ametek Gemco FG Air Application Valve (3LBS) |
A049284 |
Ametek Gemco Valve, Obsolete see A078880, Push to Release Air Valve, Normally Closed, Parking Bleed Valve (1LB) |
A049974 |
Ametek Gemco Reservoir. Dual Compartment / Split Air Reservoir (20LBS) |
A054581 |
Ametek Gemco Seal Kit 88740 |
A054582 |
Ametek Gemco Repair Kit. Valve Seal Kit for the Emergency Relay Valve # 58860 or 71891, 12 Parts, (1LB) |
A055980 |
Ametek Gemco Hydraulic Tubing, 100 FT, Copper |
A056301 |
Ametek Gemco Obsolete FG HRC Hydraulic Remote Controlled Valve see 107047 |
A064132 |
Ametek Gemco Air Pressure Regulator. (ISGSAP1267505) |
A065112 |
Ametek Gemco 30 Inch Air Hose (1LB) |
A071891 |
Ametek Gemco Valve. Relay Emergency Valve used on some Air over Hydraulic Brake systems with the parking brake option. Midland Valve modified by Ametek Gemco (5LBS) |
A075410 |
Ametek Gemco Repair Kit for the 58860 Emergency Relay Valve (1LB) |
A075422 |
Ametek Gemco Repair Kit. Obsolete 4/6 for a 98275 Disc Brake Power Cluster. 1 X 8 Pressure Ratio. Includes air piston cup & felt washer on the pneumatic side & secondary seals, main piston, secondary piston, compensating check valve, back-up washer, primary cup & zero residual check valve on the hydraulic side. 7 Inch Dia. (1LB) |
A075530 |
Ametek Gemco Cap on the Emergency Relay Valve (1LB) |
A078880 |
Ametek Gemco Valve, Push to Release Air Valve, Normally Closed, Parking Bleed Valve (1LB) |
A088740 |
Ametek Gemco Air Valve, Push to Release, Normally Closed, Parking Bleed Valve, was A049284 (1LB) ISG CLE SAP 1269786 |
A100596 |
Ametek Gemco Check Valve. No longer used or required on the panel per Frank Ernst, Ametek Gemco 11/04 |
A1502402 |
Ametek Gemco Gear Assembly. Includes Worm Gear and Hub for mounting onto the cam shaft (1LB) |
AD3017 |
Ametek Gemco Air Reservoir, Single Compartment, 2020 Cubic Inch, 42 Inches Long, 8.2 Inch Dia., Qty. 3 Holes, 3/8 Pipe Thread, (30LBs) Old price |
AD35780 |
Ametek Gemco Reservoir. Single Compartment Air Reservoir |
AE56301 |
Ametek Gemco Obsolete replaced by J107047 |
AH/ARC |
Ametek Gemco AH/ARC - Air Over Hydraulic Brake Control System. Includes pre-assembled air-over hydraulic panel J089666 for 230VDC, J070943 3/4 HP 230 VDC Compressor, (4) 18 Inch Hydraulic Brake Assemblies, Actuators, Fluid Reservoir Bleeder, Foot Air Treadle Valve, Low Air Pressure Buzzer, Air Gauge, Tubing, Hoses, Fittings & Wagner Brake Fluid |
AH/ERC 1 BRK 10'' |
Ametek Gemco Air Over Hydraulic Electric Remote Control Brake system with Qty. 1, 10 Inch Brake Assemblies |
AH/ERC 4 BRK 10'' |
Ametek Gemco Air Over Hydraulic Electric Remote Control Brake System with Qty. 4, 10 Inch Brake Assemblies. Includes Brakes, Hydraulic Actuators, Fluid Reservoir Bleeder, Bleeder Switch with Enclosure, Pre-assembled air Over Hydraulic Panel, 3/4 HP Compressor Assembly, Tubing, Hoses, Fittings & Brake Fluid. Includes optional auxiliary cab control via a Foot Operated Air Treadle Valve. 0 to 4000 FT LBS Stopping Torque. Brakes 100 LBS. Ea or 46 Kg. Total Gross 900 LBS. or 400 Kg. |
AH/ERC 4 BRK 18'' |
Ametek Gemco Air Over Hydraulic Electric Remote Control Brake system with Qty. 4, 18 Inch Brake Assemblies. |
AH/ERC-10-1 |
Ametek Gemco A/H ERC Brake System 230VDC with optional cab control and a manual FRB |
AH/HM-ERC 2-10X4 |
Ametek Gemco AH/HM-ERC 2 10X4 Brake System with Two 10 X 4 Inch Hydraulic Brakes. Air Over Hydraulic - Hydraulic Remote Control Brake System with Air Treadle Control. Brake can be controlled by remote control electrically & via a provided Air Treadle. Two 10 Inch Hydraulic Brakes provide infinitely variable progressive brake application for smooth controlled braking. 0 to 2800 LBS. / FT dynamic braking torque. Includes Qty.2, 10 Inch Hydraulic Brake Assemblies, Control Panel with Compressor Motor Controls, Reservoirs and 2, air over hydraulic Power Clusters, Quincy Industrial Compressor Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Air Treadle for Cab Control, 200 Feet of Hydraulic Tubing, 25 Tube Nuts, 6 Tube Unions, 70 Tube Clamps, 70 Tube Bushings, 4 Hose Brackets, 11 Hose Copper Gaskets, 4 30 Inch Armored Flexible Hoses & 3 Gallons of Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 10 Inch Brake Weight 161 LBS. Overall brake Width 9 - 5/8 Inch, Brake Height 28 - 1/2 Inch. Please specify AC or DC Voltage. 10 X 4 Inch Brake Wheels are not included |
AH/HRC 2, 14X6 |
Ametek Gemco AH/HRC Brake System with Two 14 X 6 Inch Hydraulic Brakes. Air Over Hydraulic - Hydraulic Remote Control Brake System with operator hydraulic control. Brake can be controlled by remote control electrically & via a provided hydraulic foot pedal. Two 14 Inch Hydraulic Brakes provide infinitely variable progressive brake application for smooth controlled braking. 0 to 2800 LBS. / FT dynamic braking torque. Includes Qty.2, 14 Inch Hydraulic Brake Assemblies, Control Panel with Compressor Motor Controls, Reservoirs and 2, air over hydraulic Power Clusters, Quincy Industrial Compressor Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 200 Feet of Hydraulic Tubing, 25 Tube Nuts, 6 Tube Unions, 70 Tube Clamps, 70 Tube Bushings, 4 Hose Brackets, 11 Hose Copper Gaskets, 4 30 Inch Armored Flexible Hoses & 3 Gallons of Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 14 Inch Brake Weight 161 LBS. Overall brake Width 9 - 5/8 Inch, Brake Height 28 - 1/2 Inch. Please specify AC or DC Voltage. 14 X 6 Inch Brake Wheels are not included. |
AHM/ERC 2 8x3 Brks & Cab |
AHM/ ERC system with (2) 8 x 3 brakes and cab control. Includes the following: 2 each J003205001 8 x 3 TYPE HM brakes (with parking) 1 each J008219002 foot pedal assembly 1 each J017616002 control cylinder 1 each J045767999 operator switch 1 each J07094____ air compressor 3/4 HP 1 each J071030005 tubing installation kit 1 each J073900005 tubing kit, 2 hose w/ 50' tubing 2 each J073903005 tubing kit, 4 hose w/ 200' tubing 1 each J_________ AHM/ ERC panel 1-2 brake system 2 each J107230 right angle tee kit 2 each PSD01801__ FRB unit |
AK73 |
Westinghouse Brake OBSOLETE see CB-75 |
B10B |
Ametek Gemco Tach. Obsolete replaced by 04573067 though some modification to the pulley & mounting bracket is required |
Brake Monitoring Option |
Ametek Gemco Brake Monitoring Module. Add on to a new cam box order. Includes: SD0195800 = Longer NEMA 1 Enclosure & Main Shaft, Micro-Adjust Cam, Snap Switch SPDT, Roller Follower, Electronic Pulse Generating Disc & Electronic Pulse Generating Switch |
BZ-2RW22-A2 |
Ametek Gemco Micro Switch, S.P.D.T. BZ-2RW22-A2 Freeport IL Open, Closed & Common Terminals 04537001 |
BZ2RW822-A2 |
Ametek Gemco Switch 04537001 |
C-6131-B |
Ametek Gemco Bracket. See C0613100 ''L'' Shape Bracket for use with a Type ''K'' 2006, 2 Circuit Switch. 90 Degree, 2 Inches Wide, Qty. 3, Slots 15/32 X 23/32 on 1.75 Inch Centers (2LBS) |
C-6132-B |
Ametek Gemco Bracket. See C0613200 ''L'' Shaped Bracket for use with a Type ''K'' 2006, 4 Circuit Switch (1LB) |
C0197400 |
Ametek Gemco Cover. Cover only for a Series 1980 NEMA 1, 1 to 4 Circuit Cam Box 5/6 |
C0197500 |
Ametek Gemco Cover. Cover only for a Series 1980 NEMA 1, 5 to 6 Circuit Cam Box 11/06 |
C0197700 |
Ametek Gemco Cover. Cover only for a Series 1980 NEMA 1, 11 Circuit Cam Box |
C0198500 |
Ametek Gemco Cover. Cover only for a Series 1980 NEMA 12, 2 to 4 Circuit Cam Box (4LBS) |
C0198600 |
Ametek Gemco Cover. Cover only for a Series 1980 NEMA 12, 5 to 6 Circuit Cam Box (6LBS) |
C0198700 |
Ametek Gemco Cover. Cover only for a Series 1980 NEMA 12, 7 to 8 Circuit Cam Box (8LBS) |
C0198800 |
Ametek Gemco Cover. Cover only for a Series 1980 NEMA 12, 9 to 12 Circuit Cam Box (10LBS) |
C035800 |
Ametek Gemco Bracket. Side Frame Bracket Stands for new smaller diameter Gate Hoist Cams (August 1993) Required update when old style cams are replaced with new smaller diameter cams. 2 per Cam Box (1LB) |
C0358000 |
Ametek Gemco Bracket. Side Frame Bracket Stands for new smaller diameter Gate Hoist Cams (August 1993) Required update when old style cams are replaced with new smaller diameter cams. 2 per Cam Box (1LB) |
C0613100 |
Ametek Gemco Bracket. ''L'' Shape Bracket for use with a Type ''K'' 2006, 2 Circuit Switch. 90 Degree, 2 Inches Wide, Qty. 3, Slots 15/32 X 23/32 on 1.75 Inch Centers (1LBS) |
C0613200 |
Ametek Gemco Bracket. ''L'' Shaped Bracket for use with a Type ''K'' 2006, 4 Circuit Switch (1LB) |
Cast Iron or Bronze Encl |
Ametek Gemco Cast Bronze Enclosure for NEMA 4 2000 Series Worm Gear Limit Switches, adder |
CB-110 |
Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / solenoid Released, 7 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 85 Ft LB Continues or 110 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel. 60 LBS. Gross Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear. |
CB-15 |
Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 4.5 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 10 Ft LB Continues or 15 FT LB Intermittent, less a 4.50 X 2.75 Inch Brake Wheel E004800. (20LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear. |
CB-160 |
Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 10 Inch Diameter, Many AC Voltages, 60 or 50 Hz., Single Phase., 160 FT LB Intermittent Duty, 125 FT LB continues Duty, less a 10.00 X 4.25 Inch Brake Wheel E010800. 78 LBS Net. Motor Freight on a skid. Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear |
CB-35 |
Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 25 Ft LB Continues or 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel E005500. (34LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear |
CB-75 |
Ametek Gemco Brake Assembly, AC Solenoid, Spring Set / Solenoid Released, 7 Inch Diameter, AC Voltages, 60 & 50 Hz., Single Phase, 50 FT LB Continues or 75 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel E007500. (60LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear |
CO197500 |
Ametek Gemco Cover. Cover only for a Series 1980 NEMA , 4 to 6 Circuit Cam Box (4LBS) |
Coil TM- 63 |
Ametek Gemco Coil for a TM-63 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 1 per brake. |
Coil TM- 83 |
Ametek Gemco Coil for a TM-83 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each (25LBS) |
Coil TM-1035 |
Ametek Gemco Coil for a TM-1035 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each (30LBS) |
Coil TM-1355 |
Ametek Gemco Coil for a TM-1355 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each |
Coil TM-1665 |
Ametek Gemco Coil for a TM-1665 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each |
Coil TM-1985 |
Ametek Gemco Coil for a TM-1985 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each 1/8 |
Coil TM-2311 |
Ametek Gemco Coil for a TM-2311 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each 3/7 |
Coil TM-3014 |
Ametek Gemco Coil for a TM-3014 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each |
Coil TM-43 |
Ametek Gemco Coil for a TM-43 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 1 per brake. |
Conversion System Type H |
Ametek Gemco A/H-ERC Conversion System for Type H Wagner Hydraulic Brake Systems. Converts a Wagner manual brake system to an Air Over Hydraulic Brake System that can be controlled remotely via an electric circuit. This conversion is for Wagner Hydraulic Brake Systems though other hydraulic brake systems could be suitable for this conversion. (system suitability investigation would be required) The Conversion System Includes: One 3/4 HP Motor Driven Compressor Assembly, One Pre- Piped and Pre-Wired Control Panel, One Two-Way Hydraulic Check Valve, One Installation Kit including all the necessary tubing, fittings & fluid. If the existing brake system does not include a Fluid Reservoir Bleeder, it is required, and is at additional cost. This system requires electrical input of 230 Volt DC or 460 Volt AC, 3 Phase, 60 Hz for the compressor and 115 Volt Control on AC Systems. Please specify AC or DC at time of order. Systems are available with the HM parking option at additional cost. |
DT-2RV212-A7 |
Ametek Gemco Switch 04537003 |
E004022 |
Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 4.5 Inch Diameter, 460 Volt AC, 60 Hz., Single Phase., 15 FT LB Intermittent, less a 4.50 X 2.75 Inch Brake Wheel E004800. (20LBS) |
E004044 |
Ametek Gemco Resistor for a TM43 Brake Assembly with a shunt wound coil. This is the standard resistor. Not to be used with rectifiers employing a Forcing Scheme. E004045 is used with a Forcing Scheme Rectifier |
E004045 |
Ametek Gemco Resistor. Forcing Resistor for use with a TM-43 Brake Assembly |
E004047 |
Ametek Gemco Brake Shoe & Lining for a TM-43 4.5 Inch Electric Brake, Bonded Non-Asbestos Lining Material. Sold each, 2 per Brake. 70 Degree Arc, 645C555G02 (2LBS) |
E004051 |
Ametek Gemco Coil. Shunt Wound Coil for a TM-43 Brake Assembly. Intermittent Duty, 1 Hour Cycle 80 Volts DC / 1.10 AMPS. Continuous Duty, 8 Hour Cycle 64 Volts DC / 0.88 AMPS. Average Cold Coil Resistance 73 OHMS. Ref # 26 1 coil per brake 645C545G16 Resistors are required in series E004044 / Forcing E004045 (16LBS) |
E004054 |
Ametek Gemco Pin on a CB35 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H01 (<1LB) |
E004055 |
Ametek Gemco Pin on a CB-15 Brake Assembly. Between Link and Lever. Ref. # 8 1 per brake. 2247C08H02 (<1LB) |
E004056 |
Ametek Gemco Pin on a CB15 Brake Assembly. Connects plunger & link. Item Ref. 6. 1 per brake 2247C08H03 (<1LB) |
E004059 |
Ametek Gemco Lever for a CB15 4 & 1/2 Inch Brake Assembly. Lever between plunger link and inner shoe arm. 2247C09H01 |
E004060 |
Ametek Gemco Rod. Adjusting Rod on a CB15 4 & 1/2 Inch Brake, 1 per brake. Ref # 17 , 3279B86G01 |
E004062 |
Ametek Gemco Link on a CB-15 brake Assembly. Between plunger & lever arm. Item Ref. 7. 1 per brake. 3279B92H01 (1LB) |
E004063 |
Ametek Gemco Spring Seat on a CB15 Brake Assembly. Ref # 10 1 per brake. Old Westinghouse # 3279B94Ho2 |
E004065 |
Ametek Gemco Spring, Main Tension on a CB15 Brake Assembly. Ref # 11 1 per brake. Old Westinghouse # 3280B02H01 |
E004070 |
Ametek Gemco Bolt. Brake Shoe Bolt for a TM43 or TM63 Brake, 27D7221H04 1/2 - 13 X 3-1/4'' LG STL G2 PLATED HEX HD CAP Ref # 15, 2 per brake (1LB) |
E004071 |
Ametek Gemco Seat/ Plate. Spring Seat / Plate on the Wheel End of a TM43 Brake, Ref. # 9, 318B777H01 (1LB) |
E004074 |
Ametek Gemco Block. Inner Hinge Block on a TM-43 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H01 |
E004075 |
Ametek Gemco Release Bushing on a TM43 Brake |
E004076 |
Ametek Gemco Main Spring Seat on a TM43 Brake Assembly |
E004077 |
Ametek Gemco Dust Seal for the Coil on a TM43 Brake Assembly |
E004078 |
Ametek Gemco Spring. Wheel End Spring on a TM-43 Brake Tie Rod Ref. # 11 1 per brake. Recommended spare part 438A070H15 (1LB) |
E004079 |
Ametek Gemco Tension Spring on a TM43 Brake Assembly |
E004080 |
Ametek Gemco Tension Spring on a TM43 Brake Assembly |
E004097 |
Ametek Gemco Tie Rod on a TM43 4 Inch Brake Assembly. Ref #7. 1 per brake. Old Westinghouse 635C104G09 |
E004098 |
Ametek Gemco Bushing for a TM43 or TM63 Brake Assembly, 2 per brake |
E004101 |
Ametek Gemco Lining and Rivet Kit on a CB15 Brake Assembly. Linings have 4 countersunk holes for the rivets. Also available undrilled for bonded applications. Old Westinghouse # 3279B95G01 1 kit per brake. recommended spare part (1LB) |
E004102 |
Ametek Gemco Coil for a CB-15 Brake. 460 Volt 60 Hz. Single Phase, 3280B04G03 (1LB) |
E004104 |
Ametek Gemco Coil for a CB-15 Brake. 115 Volt 60 Hz. Single Phase, 3280B04G01 (1LB) |
E004105 |
Ametek Gemco Coil for a CB-15 Brake. 230 Volt 60 Hz. Single Phase, 3280B04G02 (1LB) |
E004107 |
Ametek Gemco Coil for a CB-15 Brake. 200 Volt 60 Hz. Single Phase, 3280B04G17 (1LB) |
E004109 |
Ametek Gemco Solenoid Assembly on a 4.5'' Dia. CB15 Brake Assembly, includes Plunger & Solenoid Guides, 3279B97H01 |
E004113 |
Ametek Gemco Shoe with Lining, Inner, for a CB15 Brake, old 2254C28G01 |
E004114 |
Ametek Gemco Shoe with Lining, Outer, for a CB15 Brake, old 2254C27G01 |
E004117 |
Ametek Gemco Lining & Rivet Kit for a TM43 4.5 Inch Dia. Electric Brake, 1 Pair drilled for with rivets. The rivets are included. Old Westinghouse # 961C691G23. Undrilled linings for bonded application are also available. Just specify undrilled on any order. |
E004118 |
Ametek Gemco Arm. Outer Brake Shoe Arm on a TM-43 Brake. Ref # 16, 1 per brake, 645C544G01 |
E004143 |
Ametek Gemco Block. Wheel End Hinge Block for a TM43 Brake. Ref # 12 1 per brake. 318B787H01 |
E004153 |
Ametek Gemco Coil for a TM43 Brake. Series Wound Coil. 32 Amps 1/2 Hour & 26.5 Amps 1 Hour. Resistance 0.181 OHMS. |
E004154 |
Ametek Gemco Coil. Series Coil for a TM-43 Brake Assembly. 26.5 AMPS Intermittent Duty Cycle, 0.287 Ohms Resistance, G645C545G26 (8 LBS) |
E004167 |
Ametek Gemco Coil. Series Coil for a TM-43 Brake Assembly. 12.5 Amps .5 Hour & 10.3 Amps 1 Hour. Resistance 1.18 Ohms, average.. Ref # 26 1 Coil is required on this brake. Old Westinghouse # 645C545G23 |
E004175 |
Ametek Gemco Bushing. Neoprene Bushing on a CB-15 or CB-35 Brake. 2 per brake (<1LB) |
E004182 |
Ametek Gemco Series Coil for a TM-43 Brake Assembly. .Item # 26. 936 Ohms Res. 14 AMPS / 1/2 Hour . 11.5 AMPS / 1 Hour. Old Westinghouse # 208C757G16 1 per brake. |
E004500 |
Ametek Gemco Brake Wheel for the TM-43 Brake Assembly, 4.5 Inch Diameter, 3.125'' Face, 1.56 Offset, 2.62'' Hub Length, 2.75 Inch Hub Diameter, 1.625'' Maximum Bore, 9850 Maximum, RPM, Offset Hub Style ( symmetrical hub style also available), Solid Hub with centerline machined. WK2 / LB FT2 .14 Add $ 125.00 to finish hub offset, hub length, bore & key. |
E004600999-C- |
Ametek Gemco Brake Wheel 4.5 |
E004800 |
Ametek Gemco Brake Wheel for the CB15 Brake Assembly, 4.5 Inch Diameter, 2.75'' Face, 2.64'' Offset, 2.2'' Hub Length, Solid Hub with center line machined. 1.625'' Maximum Bore, 9850 Maximum RPM, 2247C13H01 Add $125.00 to finish hub, bore & keyway (9LBS) |
E005001 |
Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 230 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS) |
E005002 |
Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 460 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS) |
E005027 |
Ametek Gemco Pin on a CB35 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H04 (<1LB) |
E005028 |
Ametek Gemco Pin for a CB-35 5 & 1/2 Inch Brake Assembly. Pin connection between vertical link and main lever. 2247C08H05 (<1LB) |
E005029 |
Ametek Gemco Pin on a CB35 Brake Assembly. Connects plunger to link. Item ref. 6. 1 per brake (<1LB) |
E005031 |
Ametek Gemco Pin on a CB-35 Brake. Ref # 15. 1 per brake. 2247C08H16 (<1lb) |
E005032 |
Ametek Gemco Lever for a CB35 5 & 1/2 Inch Brake Assembly. Lever between plunger link and inner shoe arm. Old Westinghouse 2247C09H02 |
E005033 |
Ametek Gemco Rod. Adjusting Rod on a CB35 5 & 1/2 Inch Brake, 1 per brake. Ref # 17 , 3279B86G02 |
E005034 |
Ametek Gemco Spring Plate on a CB35 Brake, 3280B89H02 Old price |
E005035 |
Ametek Gemco Link for a CB35 5 & 1/2 Inch Brake Assembly. Link between solenoid plunger and top lever. 3279B92H02 |
E005036 |
Ametek Gemco Spring Seat, 3279B94H01, CB35 Brake 5.5'' Dia |
E005038 |
Ametek Gemco Spring, 3280B02H02, CB35 Brake 5.5'' Dia |
E005039 |
Ametek Gemco Brake Coil. 460 VAC 60 Hz.for a CB-35 Brake Assembly. 5 & 1/2 Inch Diameter BW. Ref # 2. 3208B04G07 (1LB) |
E005044 |
Ametek Gemco Condulet Box on a CB15 or CB35 Brake Assembly (1LB) |
E005047 |
Ametek Gemco Brake Shoe & Lining for a CB35 Brake Assembly. Outer Shoe away from solenoid. Bonded, 2254C27G02 (5LBS) |
E005048 |
Ametek Gemco Brake Shoe & Lining for a CB35 Brake Assembly. Inner Shoe, close to solenoid. Bonded, 247C28G02 (5LBS) |
E005049 |
Ametek Gemco Brake Lining Kit for a CB35 Brake Assembly. 2 Drilled Linings & Push Pins, 3279B95G02 (1LB) |
E005050 |
Ametek Gemco Solenoid Guides for a CB-15 & CB35 Brake Assembly. Brass Ref. # 5. 6753A37H02 (<1LB) |
E005051 |
Ametek Gemco Coil 115 VAC, 60 Hz for a CB35 Brake Assembly, 3280B04H05 |
E005052 |
Ametek Gemco Coil 230 Volt 60 Hz, for a CB-35 Brake Assembly, 5.5'', 3280B04G06 4256302 |
E005055 |
Ametek Gemco Solenoid Assembly on a CB-35 5.5 Inch Diameter Brake, includes the Plunger & Solenoid Guides No coil. 3279B97H02 (5LBS) |
E005057 |
Ametek Gemco Spring Plate, 3279B90G02, CB35 Brake 5.5'' Dia Replaced by E005034 |
E005071 |
Ametek Gemco Plate. Identification plate on a brake |
E005500 |
Ametek Gemco Brake Wheel, 5.5 Inch Diameter, for the CB35 Brake Assembly, 3.25 Inch Face, 2.62 Inch Offset, 2.62 Inch Hub Length, Solid Hub, 1.625'' Maximum Bore, 8050 Maximum RPM, 2247C15H01, 4205603 (12LBS) |
E006000 |
Ametek Gemco Heavy Duty Spring Set Magnetic Release Shoe Brake Assembly, Model TM-63, Direct Current Clapper Type, 6 Inch Wheel Diameter, with a Shunt Wound Coil. With a Shunt Coil 50 FT LBS @ 1 Hour. A 6 X 3.125 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost (57LBS) |
E006023 |
Ametek Gemco Brake Shoe & Lining for a TM-63 6 Inch Electric Brake, Bonded Non-Asbestos Lining Material. Sold each, 2 per Brake. 70 Degree Arc, 645C162G02 (2LBS) |
E006025 |
Ametek Gemco Resistor. External resistor forced for a TM-63 Brake Assembly |
E006026 |
Ametek Gemco Coil. Shunt Wound Coil for a TM-63 Brake Assembly. Intermittent Duty, 1 Hour Cycle 80 Volts DC / 1.35 AMPS. Continuous Duty, 8 Hour Cycle 64 Volts DC / 1.08 AMPS. Average Cold Coil Resistance 59.4 OHMS. Ref # 26 1 coil per brake 645C173G16 Resistors are required in series E006024 / Forcing E006025 (18LBS) |
E006028 |
Ametek Gemco Spring Seat / Plate, Wheel End on a TM63 Brake, 318B777H09 |
E006031 |
Ametek Gemco Pivot Pin on a TM43 or 63 Brake Assembly, 318B789H01 |
E006032 |
Ametek Gemco Block. Inner Hinge Block on a TM-63 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H09 |
E006033 |
Ametek Gemco Release Bushing, TM63, 318B792H09 |
E006034 |
Ametek Gemco Main Spring Seat / Retainer, TM63, 318B795H09 |
E006035 |
Ametek Gemco Dust seal for Coil on a TM63 Brake Assembly |
E006036 |
Ametek Gemco Spring. Wheel End Spring on a TM-63 Brake Tie Rod Ref. # 11 1 per brake. Recommended spare part 438A070H14(1LB) |
E006037 |
Ametek Gemco Main Spring for a TM63 Brake Assembly. Item # 3. 1 per brake. Old Westinghouse # 438A072H14 Recommended spare part. |
E006038 |
Ametek Gemco Tension Spring for a TM63 Brake Assembly. Item # 28. Qty. 1. 2 per brake. 438A11H06 Recommended spare part (<1LB) |
E006041 |
Ametek Gemco Outer Clapper on a TM-63 Brake assembly. Ref. # 25. 1 per brake. Old Westinghouse # 473B337G01 |
E006045 |
Ametek Gemco Adjusting Bar, TM63, 473B345H01 |
E006049 |
Ametek Gemco Tie Rod on a TM63 6 Inch Brake Assembly. Ref #7. 1 per brake. Old Westinghouse 635C104G01 |
E006056 |
Ametek Gemco Outer Shoe Arm & Bushing Assembly on a TM63 Brake Assembly, 1 per brake, 645C120G01 |
E006058 |
Ametek Gemco Screw. Adjusting Screw on a TM-63 Brake. Ref # 8, 1 per brake, 3/8 -16 X 1 & 1/2 1/6 |
E006059 |
Ametek Gemco Lining & Rivet Kit for a TM63 6 Inch Dia. Electric Brake, 1 Pair, 70 Degrees, 861C691G24 |
E006060 |
Ametek Gemco Inner Brake Shoe Arm & Bushing Assembly on a TM63 Brake Assembly, 1 per brake, 645C120G02 Ref # 20 |
E006061 |
Ametek Gemco Clapper Arm & Bushing Outer Assembly on a TM63 Brake, 1 per brake, 645C141G01 |
E006069 |
Ametek Gemco Block on the Magnet End TM63, 318B788H09 |
E006070 |
Ametek Gemco Block. Wheel End Hinge Block on a TM63 Brake. Ref # 12 1 per brake. Old Westinghouse 318B787H09 |
E006083 |
Ametek Gemco Coil. Series Coil for a TM-63 Brake Assembly. 1 Coil is required on this brake. 27.5 AMPS 1 Hour Duty, 37.0 AMPS 1/2 Hour Duty, Average Resistance 0 .163 Ohms. Ref # 26 645C173G22 (18LBS) |
E006114 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM63 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
E006500 |
Ametek Gemco Stock Bore Brake Wheel, 6 Inch Diameter, 3.125'' Face Width, 3'' Offset when measured from the centerline of the face, 3.5'' Hub Length, 2'' Maximum Bore, 3.25'' Hub Diameter, Stock Bore for the TM63 & ET-6NA Brake, (16LBS) 7937A36H Add $ 135.00 to finish the hub offset, length, bore & key. 834D992H15 |
E007002 |
Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 7 Inch Diameter, 460 VAC, Single Phase, 75 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel (60LBS) |
E007012 |
Ametek Gemco Brake Assembly. CB-110 Brake with a 40 Volt AC Coil |
E007053 |
Ametek Gemco Pin on a CB75 & CB110 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H07 (<1LB) |
E007054 |
Ametek Gemco Pin on a CB75 & 110 Brake Assembly. Ref # 8 1 per brake. Old Westinghouse # 224C08H08 |
E007055 |
Ametek Gemco Pin on a CB 75 & 110 Brake Assembly. Ref # 6 1 per brake. Old Westinghouse # 2247C08H09 |
E007057 |
Ametek Gemco Pin 2247C08H18 (<1LB) |
E007058 |
Ametek Gemco Brake Lever on a CB 75 & CB 110 Brake Assembly. Ref. # 9, 1 per brake, old Westinghouse # 2247C09H03 |
E007059 |
Ametek Gemco Rod. Adjusting Rod on a CB75 & CB110 7 Inch Brake, 1 per brake. Ref # 17 , 3279B86G03 |
E007061 |
Ametek Gemco Link for a CB75 7 Inch Brake Assembly. Link between solenoid plunger and top lever. 3279B92H03 (<1LB) |
E007062 |
Ametek Gemco Link on a CB110 Brake Assembly, 3279B92H04 |
E007063 |
Ametek Gemco Spring Seat |
E007064 |
Ametek Gemco Lining 7 Inch for a CB75 or CB110 Brake, undrilled, 3279B95H03, Qty. 1, 2 per brake (<1LB) |
E007065 |
Ametek Gemco Coil for a CB75 Brake, 460VAC, 60 Hz., 3280B04G11 (2LBS) |
E007066.1 |
Ametek Gemco Coil for a CB-110 or CB-160 Brake Assembly. 460 Volt AC, 60 Hz 3280B04G15 4264204 (3LBS) |
E007067 |
Ametek Gemco Link. Shoe Link 9510D14H03 |
E007073 |
Ametek Gemco Brake Shoe & Lining for a CB75 or CB110 7'' Diameter Brake Assembly, Outer Shoe. Bonded. Old Westinghouse 2254C27G03 (9LBS) |
E007074 |
Ametek Gemco Brake Shoe & Lining for a CB75 or CB110 7'' Diameter Brake Assembly, Inner Shoe. Bonded. Old Westinghouse 2254C28G03 (9LBS) |
E007076 |
Ametek Gemco Guides. Solenoid Guides for a CB75, 110 or 160 Brake, Ref # 5, Sold Each, 2 per brake, Old Westinghouse 6753A37H03 (1LB) |
E007078 |
Ametek Gemco Lining Kit for a CB75 or CB110 Brake 7 Inch Brake Assembly, 2 Linings & Pins (1LB) |
E007080 |
Ametek Gemco Coil for a CB75 Brake, 115 VAC, 60 Hz., Ref # 2 3280B04G09 (2LBS) |
E007081 |
Ametek Gemco Coil 230 Volt 60 Hz, for a CB-75 Brake Assembly. 7'', 3280B04G10 (2LB) |
E007087 |
Ametek Gemco Coil. 115 Volt for the CB-110 & CB-160 Brake |
E007088 |
Ametek Gemco Coil, 230 Volt AC, 60 Hz., for a CB-110 or CB-160 Brake Assembly. Old Westinghouse # 3280B04G13 4264202 |
E007091 |
Ametek Gemco Solenoid Assembly on a CB-110 7 Inch Diameter Brake Assembly, includes the Plunger & Solenoid Guides. No coil. Old Westinghouse # 3279B97H14 4206406 |
E007112 |
Ametek Gemco Bushing. Neoprene Bushing on a CB75, 110, 160 Brake, 2 per brake, 3279B96H03 (<1LB) 1/6 |
E007500 |
Ametek Gemco Brake Wheel for the CB-75 & CB-110 Brake Assembly. 7 Inch Diameter, 4.25 Inch Face Width, 3.26 Inch Offset when measured from the Centerline of the Face, 3.26 Inch Hub Length, 3.13 Inch Hub Diameter, Maximum Bore 1.875 Inch, Maximum RPM 6325, Solid Hub with the Bore Center Started, No pilot bore. ASTM A 536 Ductile Iron 80-60-03 or 80-55-06 Add $ 145.00 if you want BPI finish machine the Hub Offset, Length, Bore & Keyway (25LBS) |
E008022 |
Ametek Gemco Resistor. External Resistor for a TM-83 Brake with Shunt Wound Coils. 178 Ohm 550 Watt |
E008023 |
Ametek Gemco Resistor Bank. External Forced Resistors, 2, to be used with a control circuit employing a Forcing Scheme. Designed for a faster brake release & setting response time. TM-83 Brake |
E008025 |
Ametek Gemco Brake Shoe & Lining Complete for a TM-83 or ET-8, 8 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 439C314G01 (3LBS) |
E008026 |
Ametek Gemco Coil. Shunt Wound Coil for a TM-83 Brake Assembly. Intermittent Duty, 1 Hour Cycle 40 Volts DC / 1.28 AMPS. Continuous Duty, 8 Hour Cycle 32 Volts DC / 1.00 AMP. Average Cold Coil Resistance 31.3 OHMS per coil. Ref # 26 2 coils are required per brake, sold each. 637C504G16 Resistors are required in series E008022 / Forcing E008023 (18LBS) |
E008027 |
Ametek Gemco Bushing for the Clapper Arm on a TM83 or TM1035 Brake, 2 per brake, 31D4114H11 |
E008028 |
Ametek Gemco Bushing on a TM83 or TM1035 Brake, 12 per brake, 31D4118H04 |
E008029 |
Ametek Gemco Stop Pin on a TM83 or TM1035 Brake, 318B571H03 |
E008030 |
Ametek Gemco Clapper on a TM-83 Brake Assembly. ref. # 25. 1 per brake. Old Westinghouse # 318B634G01 |
E008031 |
Ametek Gemco Spring Seat. Wheel End Spring Seat on a TM-83 & TM-1035 Brake. Ref # 11 1 per brake. Old Westinghouse # 318B777H02 |
E008032 |
Ametek Gemco Spring Clip on a TM-83 Brake Assembly. Ref. # 27. 2 per brake. Old Westinghouse # 318B778H02 |
E008034 |
Ametek Gemco Block. Inner Hinge Block on a TM-83 Brake Tie Rod. Ref # 4. 1 per Brake 318B791H02 |
E008035 |
Ametek Gemco Adjusting Screw on a TM83 & TM1035 Brake Assembly, 1 per brake, 318B793H02 |
E008036 |
Ametek Gemco Stop for a TM83 & TM1035 Brake. Old Westinghouse # 318B794H02 |
E008037 |
Ametek Gemco Main Spring Seat / Spring Retainer for a TM-83 Brake Assembly. Ref # 2. 1 per brake. 318B795H02 Old price |
E008038 |
Ametek Gemco Dust Seal for the Coil on a TM83 Brake Assembly, 1 per brake, 318B917H02 |
E008039 |
Ametek Gemco Main Spring on a TM83 Brake Assembly, Ref. # 8, 1 per brake, a recommended spare part, 438A072H13 |
E008040 |
Ametek Gemco Spring. Tension Spring on a TM83 Brake, 438A411H04 |
E008041 |
Ametek Gemco Adjusting Screw Block on a TM83 Brake Assembly, 1 per brake, 438A502H01 |
E008042 |
Ametek Gemco Outer Brake Shoe Arms on a TM 83 Brake Assembly. 1 Pair per Brake with bushings. 439C319G03 |
E008043 |
Ametek Gemco Arm. Now E008060 Inner Brake Shoe Arm on a TM83 Brake. Ref item # 21. 1 per brake. Old Westinghouse # 439C319G04 |
E008045 |
Ametek Gemco Clapper Arm on a TM-83 Brake Assembly. Ref. # 24 1 per brake. Old Westinghouse # 439C329G03 |
E008049 |
Ametek Gemco Tie Rod on a TM-83 Brake Assembly. Ref. # 6. 1 per brake. 635C104G02 |
E008053 |
Ametek Gemco Series Coil for a TM-83 Brake Assembly. 1 Coils is required on this brake. 25 Coil Amps one hour. 36.5 Coil amps half hour. Average resistance 0.086 Ohms. Ref # 26 |
E008057 |
Ametek Gemco Lining & Rivet Kit for a TM83 Electric Brake Assembly, 1 Pair, 8 Inch Diameter, 816C691G16 |
E008059 |
Ametek Gemco Base for TM83, 439C330G01 |
E008060 |
Ametek Gemco Arm. Inner Brake Shoe Arm on a TM83 Brake. Ref item # 21. 1 per brake. Includes bushings. 439C319G02 Old price |
E008061 |
Ametek Gemco Clapper & Arm on a TM 83 Brake Assembly. 1 per brake. 439C324G01 |
E008067 |
Ametek Gemco Hinge Block on the Magnet End on a TM-1035 Brake, 469B671H02 |
E008068 |
Ametek Gemco Hinge Block. Wheel End Hinge Block on a TM-83 & TM-1035 Brake. Ref # 12 1 per brake. 318B787H03 |
E008075 |
Ametek Gemco Lead Wire for TM-43 to TM-1665 Brake Coils. Shunt wound brake coils (<1LB) |
E008085 |
Ametek Gemco Series Coil for a TM-83 Brake Assembly. 1 Coils is required on this brake. 25 Coil Amps one hour. 36.5 Coil amps half hour. Average resistance 0.086 Ohms. Ref # 26 |
E008093 |
Ametek Gemco Hand Release Assembly for a TM83 Brake Old price |
E008121 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM83 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
E008199 |
Ametek Gemco Pin. Base Pin Assembly for a ET-10 Brake. Includes 2 retaining rings Old price |
E008500 |
Ametek Gemco Brake Wheel, 8 Inch Diameter with a 3.25 Inch Face Width. For the TM-83 & ET-8 Brakes, Stock Bore (25LBS) |
E010044 |
Ametek Gemco Resistor for a TM-1035 Brake Assembly 3/7 |
E010045 |
Ametek Gemco Resistor. External resistor forced for a TM-1035 Brake Assembly. With taps set as specified on Ametek data sheet (5LBS) |
E010047 |
Ametek Gemco Brake Shoe & Lining Complete for a TM-1035 or ET-10, 10 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Non-Asbestos Bonded Lining Material 635C292G01 (5LBS) |
E010049 |
Ametek Gemco Shunt Coil for a TM-1035 Brake Assembly. 2 Coils is required on this brake. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 24 Ohms. Cost per coil brake requires 2 coils connected in series. Ref # 26 Old Westinghouse # 635C328G16 |
E010054 |
Ametek Gemco Pin on a CB160 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H10 (<1LB) |
E010055 |
Ametek Gemco Pin on a CB160 Brake Assembly, Item Ref. 8 1 per brake Connects top of link to brake lever 2247C08H11 (<1LB) |
E010056 |
Ametek Gemco Pin on a CB160 Brake Assembly, Item Ref. 6. 1 per brake Connects plunger to link 2247C08H12 (<1LB) |
E010058 |
Ametek Gemco Pin 2247C08H20 |
E010059 |
Ametek Gemco Lever 2247C09H04 |
E010062 |
Ametek Gemco Link on a CB160 Brake Assembly, 3279B2H05 |
E010064 |
Ametek Gemco Spring. Main Spring on a CB160 Brake Assembly. Ref # 11 1 per brake. 3280B01H01 (1LB) |
E010068 |
Ametek Gemco Base for a CB-160 Brake Assembly. Ref. # 1 1 per brake 9510D16H04 |
E010069 |
Ametek Gemco Conduit Box on a CB75, 110 or 160 Brake Assembly, 9510D19G01 |
E010070 |
Ametek Gemco Bolt. Brake Shoe Bolt Assembly on a TM-83, TM-1035 & ET-10 Brake. Ref. # 16. 2 per brake. 27D7221H14 |
E010072 |
Ametek Gemco Pin. Pivot Pin for a TM83 or 1035 Brake, Item Ref # 19, 4 per brake, 318B789H03 (<1LB) |
E010073 |
Ametek Gemco Pin. Tension Spring Pin on a TM83 or 1035 Brake Assembly, 438A411H03 (1LB) |
E010074 |
Ametek Gemco Block. Inner Hinge Block on a TM-1035 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H03 |
E010075 |
Ametek Gemco Bushing. Release Bushing on a TM-1035 Brake. Ref # 5 1 per brake. 318B792H02 |
E010076 |
Ametek Gemco Main Spring Seat / Spring Retainer for a TM-1035 Brake Assembly. Ref # 2. 1 per brake. 318B795H03 |
E010077 |
Ametek Gemco Dust Seal for the Coil on a TM-1035. Old Westinghouse # 318B917H03 |
E010078 |
Ametek Gemco Clapper on a TM-1035 Brake Assembly. Ref # 25. 1 per brake. 318B988G01 |
E010079 |
Ametek Gemco Spring. Wheel End Spring on a TM-83 & 1035 Brake Tie Rod. Ref. # 10. 1 per brake. 438A070H13. Recommended spare part (1LB) |
E010080 |
Ametek Gemco Main Spring on a TM1035 brake. Ref # 3. 1 per brake. Recommended spare part. 438A072H11 |
E010083 |
Ametek Gemco Adjusting Screw Block on a TM1035 Brake. Ref # 7. 1 per brake. 438A217H01 |
E010085 |
Ametek Gemco Spring. Tension Spring on a TM-1035 Brake, Ref. # 28. 2 per brake. Recommended spare part 438A411H03 (1LB) |
E010086 |
Ametek Gemco Tie Rod on a TM1035 10 Inch Brake Assembly. Ref # 6. 1 per brake. 635C104G03 |
E010096 |
Ametek Gemco Solenoid Guide, same as E007076, for a CB110 or 160 Brake Assembly |
E010098 |
Ametek Gemco Rod. Adjusting Rod on a CB160 10 Inch Brake, 1 per brake. Ref # 17 , 3279B86G04 |
E010103 |
Ametek Gemco Solenoid Assembly on a 10.00'' Dia. CB160 Brake Assembly, includes the Plunger & Solenoid Guides, 3279B97H05 (8LBS) |
E010106 |
Ametek Gemco Shoe & Lining. Brake Shoe & Lining, Inner Shoe for a CB160 10 Inch Electric Brake. 2254C28G04 |
E010107 |
Ametek Gemco Shoe & Lining. Brake Shoe & Lining, Outer Shoe for a CB160 10 Inch Electric Brake. 2254C27G04 |
E010108 |
Ametek Gemco Lining & Rivet Kit for a CB160 Brake, ( Drilled Lining with required Push Pins) 3279B95G04 |
E010109 |
Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 2 Coils per brake assembly. 39.00 AMPS per coil continuous duty / 130 FT LB, 54 AMPS per coil intermittent duty / 200 Ft LB, average resistance.209 Ohms. Cost per coil brake requires 2 coils connected in series. Ref # 26 Old Westinghouse # 635C328G22 |
E010109002 |
Ametek Gemco 13 Inch Brake with E0109002 Coils |
E010111 |
Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 20.00 AMPS per coil continuous duty @ 130 FT LB, 27.5 AMPS per coil intermittent duty @ 200 FT LB. Average resistance .209 Ohms. 2 Coils per brake, cost per coil, coils are connected in series. Ref # 26 Old Westinghouse # 635C328G20 |
E010114 |
Ametek Gemco Lining Kit, pair of drilled linings & fasteners for a TM1035, 10 Inch Diameter Brake, 861C691G17, 104-3445D ( 8 holes 10-10 Rivet Qty 18 ) |
E010115 |
Ametek Gemco Outer Brake Shoe Arm on a TM-1035 Brake Assembly.Item 17. 635C306G01, 1 per brake. |
E010116 |
Ametek Gemco Base Assembly for a TM-1035 brake assembly. Item 18. 1 per brake 635C300G01 |
E010117 |
Ametek Gemco Arm. Inner Brake Shoe Arm on a TM-1035 Brake Assembly. Item 21. 635C306G02, 1 per brake |
E010118 |
Ametek Gemco Clapper & Arm for a TM1035 Brake. 1 per brake. Ref # 22. 635C317G01 |
E010119 |
Ametek Gemco Clapper Arm on a TM-1035 Brake Assembly. Ref # 24. 1 per brake. 635C308G01 |
E010131 |
Ametek Gemco Actuator. Hydraulic Actuator for a ETH10 Brake Assembly. Actuator for cab control. 2 to 4 Weeks 11/04
|
E010165 |
Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 75 Amps per Coil 1/2 Hour Rating. 55 Amps per Coil 1 Hour Rating. Resistance 0.0262 Ohms per Coil. Sold each / 2 coils per brake |
E010193 |
Ametek Gemco Actuating Cylinder for a Electro-Hydraulic Brake. ETH-8 & ETH-10, H4-F-N 2.0'' bore 1'' Stroke, 1'' rod, #4 Rod End, H4-F-N2.0X-1.00X1.00XXS13 Old price |
E010237 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1035 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
E010266 |
Ametek Gemco Spring. Main Spring on a ET-10 Brake |
E010286 |
Ametek Gemco Self Adjust Assembly Kit for an ET10 Brake |
E010309 |
Ametek Gemco Tie Rod Assembly for an ET-10 Brake |
E010326 |
Ametek Gemco Rectifier Assembly for a TM-43 through TM-1985 Brake Assembly. A NEMA 4 Enclosure is supplied. 16.0'' H X 14.00'' W X 8.0'' D. An open chassis unit is available at less cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (54LBS) |
E010327 |
Ametek Gemco Rectifier Assembly for a TM-43 through TM-1985 Brake Assembly. Open chassis design without enclosure. A NEMA 4 enclosure is available at additional cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (30LBS) |
E010500 |
Ametek Gemco Brake Wheel, 10 Inch Diameter for the TM-1035 Brake, Stock Bore (40LBS) |
E010622 |
Ametek Gemco Resistor External for a TM-1665 Brake Assembly, Old Westinghouse 47D0146G09 Ohms resistance required in line for 250 VDC 37.7 Ohms / 4.7 Amp |
E010800 |
Ametek Gemco Brake Wheel for the CB-160 Brake Assembly. 10 Inch Diameter, 4.25 Inch Face Width, 4.26 Inch Offset when measured from the Centerline of the Face, 3.38 Inch Hub Length, 3.75 Inch Hub Diameter, Maximum Bore 2.25 Inch, Maximum RPM 4425, Solid Hub with the Bore Center Started, No pilot bore. ASTM A 536 Ductile Iron 80-60-03 or 80-55-06 Add $ 165.00 if you want BPI finish machine the Hub Offset, Length, Bore & Keyway |
E011500 |
Ametek Gemco Brake Wheel, 11 Inch Diameter for the ET-11 Brake, Stock Bore (45LBS) |
E013022 |
Ametek Gemco Resistor External for a TM-1355 Brake Assembly. STD 110.8 OHM 650 Watt. 250 VDC without discharge resistor. |
E013023 |
Ametek Gemco Forcing Resistor for a TM-1355 Brake Assembly. 423A299G03 |
E013025 |
Ametek Gemco Brake Shoe & Lining Complete for a TM1355 or ET13, 13 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 439C201G01 (12LBS) |
E013026 |
Ametek Gemco Coil. Shunt Wound Coil for a TM-1355 Brake Assembly. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance per coil 19 Ohms. Cost per coil, brake requires 2 coils connected in series. Ref. # 26 637C384G16 |
E013027 |
Ametek Gemco Bushing for a TM1355 Brake. Qty. 1, 6 per brake. 31D4114H12 (1LB) |
E013028 |
Ametek Gemco Bushing for a TM1355 Brake. Qty. 1, 8 per brake. Ref # 19. 31D4118H06 (1LB) |
E013029 |
Ametek Gemco Clapper on a TM-1355 Brake Assembly. Ref. # 25. 1 per brake. 318B560G01 |
E013031 |
Ametek Gemco Seat. Wheel End Spring Seat on a TM1355 Brake assembly, 1 per Brake, 318B777H04 |
E013032 |
Ametek Gemco Spring Clip on a TM-1355 Brake Assembly. Ref # 27 2 per brake. 318B778H04 (1LB) |
E013033 |
Ametek Gemco Replaced by E013125 |
E013034 |
Ametek Gemco Pin. Pivot Pin used on the TM1355 Brake. Sold each, 4 per brake. 318B789H04 (2LB) |
E013035 |
Ametek Gemco Pin. Tension Spring Pin on a TM-1335 Brake Assembly. Ref # 29 1 per brake. 318B790H04 (1LB) |
E013036 |
Ametek Gemco Block. Inner Hinge Block on a TM-1355 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H04 |
E013037 |
Ametek Gemco Release Bushing on a TM1355 & TM1665 Brake Assembly, 1 per Brake, 318B792H04 |
E013038 |
Ametek Gemco Stop for a TM1355 & TM1665 Brake. 318B794H04 9/6 (<1LB) |
E013039 |
Ametek Gemco Main Spring Seat / Retainer on a TM1355 Brake Assembly, 1 per Brake, 318B795H04 |
E013040 |
Ametek Gemco Seal. Dust Seal for coil on a TM-1355 Brake Assembly. 1 per brake. 318B917H04 (1LB) |
E013041 |
Ametek Gemco Spring. Wheel End Spring on a TM1355 Brake Tie Rod. Ref No. 10 1 per Brake Recommended Spare Part 438A070H09 (2LBS) |
E013042 |
Ametek Gemco Spring. Main Spring for a TM1355 13 Inch Brake, Coil End, 1 per Brake, 438A072H09 |
E013044 |
Ametek Gemco Spring. Tension Spring on a TM1355 & TM1665 Brake, 438A411H05 (1LB) |
E013045 |
Ametek Gemco Adjusting Screw Block on a TM1355 Brake. Ref # 7. 1 per brake. 438A456H01 |
E013051 |
Ametek Gemco Bracket. Magnet Travel Equalizer Bracket on a TM-1355 Brake |
E013052 |
Ametek Gemco Tie Rod for a TM1355 13 Inch Brake. Ref. #6, 1 per Brake. 861C691G18 |
E013053 |
Ametek Gemco Brake Shoe Bolt on a TM1355, 2 per Brake, 24D6387G04. Item 3 |
E013055 |
Ametek Gemco Lining Kit, pair of drilled & countersunk linings with fasteners for a TM1355, 13 Inch Diameter Brake. 861C691G18 (3LBS) |
E013056 |
Ametek Gemco Clapper Arm on a TM-1355 Brake Assembly. Ref. # 24. 1 per brake. 439C203G01 |
E013058 |
Ametek Gemco Coil. Series Coil for a TM13 Brake, 2 per brake, sold each, 637C551G16, 608 Mill Motor, 0.0358 Ohms Resistance Average, 85 Amps 1/2 Hour, 63 Amps 1 Hour (60 LBS) |
E013059 |
Ametek Gemco Coil. Series Coil for a TM13 Brake, 2 per brake, sold each, 637C551G17, 606 Mill Motor, Ohms Resistance Average, Amps 1/2 Hour, Amps 1 Hour (60 LBS) |
E013064 |
Ametek Gemco Arm. Outer Brake Shoe Arm on a TM-1355 Brake Assembly. Ref. # 17. 1 per brake. 439C192G05 |
E013066 |
Ametek Gemco Base on a TM-1355 Brake Assembly. Ref. #18. 1 per brake. 439C204G01 |
E013067 |
Ametek Gemco Inner Brake Shoe Arm on a TM-1355 Brake Assembly. Ref. #21. 1 per brake. old Westinghouse # 439C192G06 |
E013068 |
Ametek Gemco Clapper & Arm for a TM1355 Brake. 1 per brake. Ref # 22. 489C202G01 |
E013073 |
Ametek Gemco Spring Clip on a TM1355 Brake. Hand Release. 1 per brake. Old Westinghouse # 450A574H03 (1LB) |
E013098 |
Ametek Gemco Coil. Series Wound Coil for a TM-1355 Brake. 637C551G23, 54 AMPS 1/2 Hour Rating, 40 AMPS 1 Hour Rating, .081 OHMS per coil, 2 per brake, sold each |
E013125 |
Ametek Gemco Hinge Block on the Magnet End of a TM1355 Brake, 1 per Brake, 318B788H04 |
E013146 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1355 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
E013194 |
Ametek Gemco Base for a ET13 Brake Assembly. item 1 |
E013214 |
Ametek Gemco Main Spring on a ET-13 Brake E013214 & 04581104. Item 9A |
E013225 |
Ametek Gemco Arm. Inner Shoe Arm on a ET-13 Brake. 1 Pair. Item 6 |
E013228 |
Ametek Gemco Tie Rod Assembly for a ETH13EB50 Brake. Item 5 |
E013229 |
Ametek Gemco Force Arm Assembly on a ET-13 Brake. Item 7 |
E013231 |
Ametek Gemco Pin Kit for a ET-13 Brake. Includes Base Pins and Top Pins with Retaining Rings. Item 10 |
E013240 |
Ametek Gemco Tie Rod. Self Adjust Tie Rod Assembly on a ET-13 Brake with the Self Adjust Option. Item 5A 4/7 |
E013500 |
Ametek Gemco Stock Bore Brake Wheel, 13 Inch Diameter, for the TM-1355 Brake Assembly, 5.75'' Face Width, 5.375'' Offset when measured from the centerline of the face, 5.00'' Hub Length Add $ 185.00 if you want BPI to finish machine the Hub Offset, Hub Length, Bore & Keyway (100LBS) |
E013513 |
Ametek Gemco Brake Wheel 13 Inch Diameter with a hub length bore & keyway for an 808 Mill Motor with the AISE Standard Offset |
E014500 |
Ametek Gemco Brake Wheel 14 Inch Diameter. Pilot Bore, TM & ET Brakes |
E016022 |
Ametek Gemco Series Resistor for a TM-1665 Brake Assembly with Shunt Wound Coils. Old Westinghouse Part # 423A298G04 51 OHMS 250 VDC |
E016023 |
Ametek Gemco Resistor. External resistor forced for a TM-1665 Brake Assembly. With taps set as specified on Ametek data sheet (5LBS) |
E016025 |
Ametek Gemco Brake Shoe & Lining Complete for a TM-1665 or ET-16, 16 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Non-Asbestos Material Bonded to the Brake Shoe 635C227G01 (31LBS) |
E0160251 |
Ametek Gemco Brake Shoe & Lining Complete, Bonded, for a TM1655 or ET16, 16 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, 635C227G01 |
E016026 |
Ametek Gemco Shunt Coil for a TM-1665 Brake Assembly. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 8.8 Ohms. Cost is per coil brake requires 2 coils connected in series. Ref # 26 635C247G17 |
E016027 |
Ametek Gemco Bolt. Brake shoe Bolt on a TM1655 & ET-16 Brake.Includes Bolt, Nut & Pin. Ref item 16. 2 per brake, 24D6387G03 (2LBS) |
E016028 |
Ametek Gemco Pin on a TM1665 Brake, 1 per Brake, 318B571H05 |
E016030 |
Ametek Gemco Spring Clip on a TM-1665 Brake Assembly. Ref # 27 2 per brake. 318B778H05 |
E016031 |
Ametek Gemco Block. Wheel End Hinge Block on a Old TM1355 Brake Assembly, 1 per Brake, 318B787H05. New Style Brake uses a E016205 |
E016033 |
Ametek Gemco Pivot Pin on a TM1665 Brake Assembly. Ref. # 20, 4 per brake. 318B789H05 |
E016034 |
Ametek Gemco Pin. Tension Spring Pin on a TM-1665 Brake Assembly. Ref # 29 1 per brake. 318B790H05 (<1LB) |
E016035 |
Ametek Gemco Block. Inner Hinge Block on a TM-1665 Brake Tie Rod. Ref. #4. 1 per Brake, 318B791H05 |
E016036 |
Ametek Gemco Screw, Adjusting Screw on a TM1355 & 1665 Brake, 1 per Brake, 318B793H04 (1LB) |
E016038 |
Ametek Gemco Seal. Dust Seal for coil on a TM-1655 Brake Assembly. 1 per brake. 318B917H05 (1LB) |
E016039 |
Ametek Gemco Spring. Main Spring for a TM-1665 16 Inch Brake, Coil End, 1 per Brake, Recommended Spare Part 438A072H07 |
E016040 |
Ametek Gemco Adjusting Screw Block on a TM1665 Brake Tie Rod. 438A352H01 |
E016050 |
Ametek Gemco Clapper on a TM-1665 Brake Assembly. Ref #25. 1 per brake. 318B907G01 |
E016051 |
Ametek Gemco Base on a TM-1665 Brake assembly. Ref. #18. 1 per brake. Old Westinghouse # 635C235G01 |
E016052 |
Ametek Gemco Clapper & Arm on a TM-1665 Brake Assembly. Ref. #22. 1 per brake. Old Westinghouse #635C236G01 |
E016053 |
Ametek Gemco Lining Kit, pair of linings & fasteners for a TM1655, 16 Inch Diameter Brake old 861C691G19. New brakes use bonded linings. 7 LBS Gross |
E016054 |
Ametek Gemco Coil. Shunt Coil, Special Shunt Coil for a TM16 Brake, 2 per brake, sold each, 637C530G16, 808 / 610 Mill Motors, 0.0195 Ohms Resistance Average, 90 Volts Intermittent, 1 Hour / 125 Volts Continues Duty Cycle, 8 Hour. Specifications are for a single coil (100LBS) 7/7 |
E016055 |
Ametek Gemco Series Coil for a TM-1665 Brake. Quoted each, 2 per brake. It is recommended that Series Coils are replaced in pairs. 637C530G19 7/7 |
E016060 |
Ametek Gemco Outer Brake Shoe Arm with Bushings on a TM1665 Brake. Ref. # 17. 1 per brake. 635C240G01 |
E016061 |
Ametek Gemco Inner Brake Shoe Arm with Bushings on a TM1665 Brake. Ref. #21. 1 per brake. 635C240G02 |
E016062 |
Ametek Gemco Eyebolt, part of Hand Release Assembly on a TM-1665 Brake |
E016063 |
Ametek Gemco Clapper Arm on a TM-1665 Brake Assembly. Ref. #24. 1 per brake. Old Westinghouse #635C238G01 |
E016064 |
Ametek Gemco Handle, part of Hand Release assembly on a TM1665 Brake |
E016065 |
Ametek Gemco Outer Block, part of the Hand Release Assembly on a TM-1665 Brake. Welded in place. |
E016073 |
Ametek Gemco Hinge Block, Magnet End on a TM1665 Brake Assembly, |
E016089 |
Ametek Gemco Actuator. Hydraulic Override Cylinder on a ETH-14 Brake Assembly. Slave cylinder for cab operation. |
E016105 |
Ametek Gemco Tie Rod Assembly for a TM-1665 Brake. New larger diameter tie-rod completely populated with all components for installation on an older brake. Includes items 1 thru 6, 10 thru 12 and miscellaneous hardware. |
E016108999 |
Ametek Gemco Hydraulic Actuator on a ETH-16 Thruster Brake with Slave Cylinder |
E016200 |
Ametek Gemco Tie Rod on a TM1665 16 Inch Brake Assembly. Ref # 6. 1 per brake. Old Westinghouse 635C104G05 |
E016203 |
Ametek Gemco Wheel End Spring Seat on a TM1665 Brake Assembly, 1 per Brake, 318B777H05 |
E016205 |
Ametek Gemco Hinge Block, Wheel End Hinge Block on a TM1355 or TM-1665 Brake, 1 per Brake, new style 1/6 |
E016206 |
Ametek Gemco Main Spring Seat on a TM1665 Brake Assembly, 1 per Brake, 318B795H05 |
E016207 |
Ametek Gemco Spring. Wheel End Spring on a TM 1665 Brake Tie Rod. Ref No. 10 1 per Brake Recommended Spare Part (2LBS) |
E016210 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1665 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
E016224 |
Ametek Gemco Block. Inner Tie Rod Block on a ETH14NA Brake |
E016232 |
Ametek Gemco Pin. Pin for the Inner Tie Rod Block on a ETH14NA Brake. Includes Grease Fittings & Retaining Rings (<1LB) |
E016500 |
Ametek Gemco Brake Wheel 16 Inch Diameter. Pilot Bore, TM & ET Brakes |
E018500 |
Ametek Gemco Brake Wheel 16 Inch Diameter, Pilot Bore, TM & ET Brakes |
E019022 |
Ametek Gemco Resistor. External resistor forced for a TM-1985 Brake Assembly |
E019024 |
Ametek Gemco Brake Shoe & Lining Complete for a TM-1985 or ET-19, 19 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 439C394G01 (45LBS) 1/8 |
E019025 |
Ametek Gemco Coil. Shunt Coil for a TM-1985, 19 Inch Brake Assembly. 2 Coils are used on this brake. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 8.5 Ohms. Coils are connected in series. Ref # 26. Price shown is for a single 1 coil 1/8 |
E019027 |
Ametek Gemco Brake Shoe Bolt on a TM1985 or ET19 Brake Assembly. Page Ref. # 16. 2 per brake. 24D6387G01 1.25'' Dia. X 10.5'' L Rod threaded both ends 1 end has pin hole, Nut for use with pin, 1 pin. Nut is on & pinned (5 LBS) 8/7 2 Weeks |
E019028 |
Ametek Gemco Bushing on the Shoe Clapper Arm for a TM1985 orTM2311 Brake, 2 per brake 31D4114H20 3/7 (<1LB) |
E019029 |
Ametek Gemco Bushing on the Brake Base for the TM1985 and TM2311 Brakes, 8 per Brake / 4 Pair 31D4118H19 (1LB) 6/6 |
E019030 |
Ametek Gemco Pin. Stop Pin on a TM1985 Brake, 318B571H06 6/6 |
E019031 |
Ametek Gemco Clapper Assembly on a TM-1985 Brake. Ref. #25. 1 per brake 318B670G01 1/7 |
E019032 |
Ametek Gemco Wheel End Spring Seat on a 19 Inch Frame 1985 Brake, 1 per Brake, 318B777H06 6/6 |
E019033 |
Ametek Gemco Spring Clip on a TM-1985 Brake Assembly. Ref. #27. 2 per brake. Old Westinghouse #318B778H06 |
E019036 |
Ametek Gemco Pin. Pivot Pin on a TM1985 Brake, 4 per Brake, 318B789H06 3/7 |
E019037 |
Ametek Gemco Pin. Tension Spring Pin on a TM-1985 Brake Assembly. Ref # 29 1 per brake. 318B790H06 1/6 |
E019038 |
Ametek Gemco Block. Inner Hinge Block on a TM-1985 Brake Tie Rod. Ref # 4 1 per Brake 318B791H06 8/6 |
E019039 |
Ametek Gemco Release Bushing, 19 and 23 Inch Brakes, 1 per Brake, 318B792H06 6/6 2 to 3 Weeks |
E019040 |
Ametek Gemco Adjusting Screw for a TM1985 & TM2311 Brake Assembly. Page Ref. # 8. 1 Per Brake. 318B793H06 6/6 |
E019042 |
Ametek Gemco Main Spring Seat on a TM1985 Brake Assembly, 1 per Brake, 310B795H06 6/6 |
E019043 |
Ametek Gemco Dust Seal for the Coil on a TM1985 Brake, 1 per Brake, 318B917H06 6/6 |
E019044 |
Ametek Gemco Main Spring on a TM1985 Brake Assembly, 1 per brake, 438A072H05 8/6 |
E019045 |
Ametek Gemco Indicator Bracket on TM-1355 to TM-1985 Brakes. Mounts to coils, facilitates brake adjustment (<1LB) |
E019048 |
Ametek Gemco Adjusting Screw Block. Inner, on a TM1985 Electric Brake Assembly, 1 per Brake, 438A219H01 6/6 |
E019057 |
Ametek Gemco Tie Rod on a TM1985 19 Inch Brake Assembly. Ref # 6. 1 per brake. 635C104G06 6/6 2 to 3 Weeks |
E019058 |
Ametek Gemco Outer Brake Shoe Arm with Bushings on a TM1985 Brake. Ref. # 17. 1 per brake. Old Westinghouse # 439C395G01 |
E019059 |
Ametek Gemco Clapper & Arm for a TM 1985 Brake, 1 Per brake, 439C397G01 |
E019060 |
Ametek Gemco Clapper Arm. Outer Clapper Arm on a TM-1985 Brake Assembly. Includes Bushings. Ref. #24. 1 per Brake 439C398G03 1/7 |
E019061 |
Ametek Gemco Coil. Series Wound Coil for a TM1985 Brake, 2 Coils per brake sold individually / each, 637C729G16 (100LBS) 1/8 |
E019062 |
Ametek Gemco Coil. Series Coil for a TM1985 Brake, 2 per brake, sold each, 637C523G16, 810 /612 Mill Motors, 0.124 Ohms Resistance Average, 180 Amps 1/2 Hour, 137 Amps 1 Hour (150LBS) 1/8 |
E019065 |
Ametek Gemco Lining Kit, pair of drilled linings & rivet fasteners for a TM1985, 19 Inch Diameter Brake 861C691G20, 10-14 Rivet, also available undrilled for bonded brake shoes (8LBS) 6/6 |
E019066 |
Ametek Gemco Base on a TM-1985 Brake Assembly. Ref. #18. 1 per brake. Old Westinghouse #439C399G01 |
E019067 |
Ametek Gemco Inner Brake Shoe Arm with Bushings on a TM-1985 Brake. Ref. #21. 1 per brake. Old Westinghouse # 439C395G02 |
E019070 |
Ametek Gemco Hinge Block on the magnet end of a TM1985 Brake Assembly, 318B788H06 6/6 |
E019071 |
Ametek Gemco Wheel End Hinge Block on a TM-1985 Brake Assembly. Ref. # 12. 1 per brake. Old Westinghouse # 318B787H06 |
E019088 |
Ametek Gemco Coil. Series Wound Coil for a TM-1955 Brake. 2 Coils per brake sold individually / each. 637C729G17 .002 OHMS / coil. 616 or 814 1/8 |
E019119 |
Ametek Gemco Lead. Coil Lead TM-1985 to TM-3014 Brake Coils. Shunt wound coils. 2 per brake (1LB) |
E019125 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1955 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
E019172 |
Ametek Gemco Tie Rod for an ET19 Brake, 1 per brake (15LBS) |
E019190 |
Ametek Gemco Tie Rod Assembly Complete with all attached components for a TM-1985 Brake Assembly |
E019500 |
Ametek Gemco Brake Wheel 19 Inch Diameter Pilot Bore TM & ET Brakes |
E019503002-G- |
Ametek Gemco Brake Wheel |
E019527002 |
Ametek Gemco Brake Wheel |
E019527002-G- |
Ametek Gemco Brake Wheel |
E019530002-G- |
Ametek Gemco Brake Wheel |
E023022 |
Ametek Gemco Series Resistor |
E023023 |
Ametek Gemco Resistor. External resistor forced for a TM-2311 Brake Assembly. With taps set as specified on Ametek data sheet, Old Westinghouse # 423A299G06 (5LBS) |
E023025 |
Ametek Gemco Brake Shoe & Lining Complete for a TM-2311, 23 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 635C316G01 1/8 |
E023026 |
Ametek Gemco Coil for a TM-2311 Brake Assembly. Shunt Wound. 2 Coils are required for this brake. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 6.1 Ohms. Cost per coil, brake requires 2 coils connected in series. Ref # 26. Old # 637C373G16 3/7 |
E023027 |
Ametek Gemco Spring. Wheel End Spring on a TM 19, 23 or 30 Inch Brake Tie Rod. Ref No. 10 1 per Brake Recommended Spare Part 24D5096H11 (3LBS) 2/7 |
E023028 |
Ametek Gemco Bolt. Brake Shoe Bolt on a TM2311 Brake Assembly. 2 per Brake, 24D6387G02 2/7 |
E023029 |
Ametek Gemco Stop Pin on a TM2311 Brake, 1 Per Brake, 318B571H07 2/7 |
E023030 |
Ametek Gemco Seat. Wheel End Spring Seat on a TM2311 Brake Assembly, 1 per brake, 318B777H07 8/6 |
E023031 |
Ametek Gemco Spring Clip on a TM-2311 Brake Assembly. Ref. #27. 2 per brake. Old Westinghouse #318B778H07 |
E023034 |
Ametek Gemco Pin. Pivot Pin for a TM2311 Electric Brake, 4 per Brake, 318B789H07 |
E023035 |
Ametek Gemco Pin. Tension Spring Pin on a TM2311 Brake Assembly, 1 per Brake, 318B790H07 |
E023036 |
Ametek Gemco Block. Inner Hinge Block on a TM-2311 Brake Tie Rod. Ref. #4. 1 per Brake, 318B791H07 8/6 |
E023038 |
Ametek Gemco Main Spring Seat on a TM-2311 Brake. 1 per brake 318B795H07 9/6 |
E023039 |
Ametek Gemco Dust Seal for Coil on a TM2311 Electric Brake, 1 Per Brake,318B917H07 |
E023040 |
Ametek Gemco Clapper on a TM-2311 Brake Assembly. Ref. #25. 1 per brake. Old Westinghouse #319B098G01 |
E023044 |
Ametek Gemco Spring. Tension Spring for a 19 or 23 Inch TM Brake, 438A069H05 6/6 |
E023045 |
Ametek Gemco Spring. Main Spring on a TM2311 Brake Assembly. Item 3. 438A072H03, 1 per brake. Recommended spare part 8/6 |
E023046 |
Ametek Gemco Adjusting Screw Block for a TM2311 Brake Assembly, 1 per Brake, 438A429H01 |
E023047 |
Ametek Gemco Tie Rod on a TM2311 23 Inch Brake Assembly, Ref. #6, 1 per Brake, 635C104G07. |
E023051 |
Ametek Gemco Clapper Arm on a TM-2311 Brake Assembly. Ref. #24. 1 per brake. 637C362G01 |
E023052 |
Ametek Gemco Clapper & Arm on a TM-2311 Brake Assembly. Ref. #22. 1per brake. 637C343G01 |
E023053 |
Ametek Gemco Series Wound Coil for a TM2311 Brake. Qty 1, 2 per brake. 637C502G17 |
E023054 |
Ametek Gemco Series Wound Coil for a TM2311 Brake. Qty 1, 2 per brake. 637C502G16 |
E023055 |
Ametek Gemco Lining Kit, pair of drilled linings & fasteners for a TM2311, 23 Inch Diameter Brake 861C691G21 11/6 |
E023056 |
Ametek Gemco Outer Brake Shoe Arm on a TM-2311 Brake Assembly. Ref. #17. 1 per brake. 637C324G01 |
E023057 |
Ametek Gemco Base on a TM-2311 Brake Assembly. Ref. #18. 1 per brake. 434C392G01 |
E023058 |
Ametek Gemco Inner Brake Shoe Arm on a TM-2311 Brake Assembly. Ref. #21. 1 per brake. 637C324G02 |
E023062 |
Ametek Gemco Hinge Block on the magnet end of a TM2311 Brake, 1 per brake, 318B788H07 |
E023063 |
Ametek Gemco Block. Wheel End Hinge Block on a TM-2311 Brake. Ref. # 12 1 per brake, 318B787H07 8/6 |
E023080 |
Ametek Gemco Coil. Series Coil for a TM-2311. 246.0 AMPS @ .5 Hr / 183.0 AMPS @ 1.0 Hr Resistance OHMS per Coil = .0100 637C520G20 3/7 |
E023095 |
Ametek Gemco Coil. Series Coil for a TM-2311. 105.0 AMPS @ .5 Hr / 80.0 AMPS @ 1.0 Hr Resistance OHMS per Coil = .0550 186C862G16 3/7 |
E023124 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM2311 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
E023204 |
Ametek Gemco Rectifier Assembly for a TM-2311 or TM-3014 and can be used for Qty. 2, TM-43 to TM1985 Brake Assemblies. Supplied with a NEMA 4 Rated Enclosure. An open chassis design is available at less cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (40LBS) |
E023205 |
Ametek Gemco Rectifier Assembly for a TM-2311 or TM-3014 and can be used for Qty. 2, TM-43 to TM1985 Brakes. Open chassis design without enclosure. A NEMA 4 enclosure is available at additional cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (40LBS) |
E023500 |
Ametek Gemco Brake Wheel 23 Inch Diameter with a Pilot Bore BE231001 |
E023513 |
Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 612 or 812 Mill Motor. AISE Standard Offset of 8.25 inches BE231003 |
E023514 |
Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 614 or 814 Mill Motor. AISE Standard Offset of 8.25 inches BE231004 |
E023515 |
Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 616 or 816 Mill Motor. AISE Standard Offset of 8.25 inches BE231002 |
E023516 |
Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 618 or 818 Mill Motor. AISE Standard Offset of 8.75 inches BE231005 |
E023520 |
Ametek Gemco Brake Wheel 23 Inch Diameter |
E023521 |
Ametek Gemco Brake Wheel 23 Inch Diameter with a pilot bore |
E030023 |
Ametek Gemco Resistor. External resistor forced for a TM-3014 Brake Assembly |
E030024 |
Ametek Gemco Coil. Shunt Wound Coil for a TM-3014 Brake Assembly. 2 Coils per brake, sold each. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 4.5 Ohms. Ref # 26 |
E030025 |
Ametek Gemco Main Spring on a TM-3014 Brake Assembly. Item #3, a recommended spare part. 1 per Brake 438A072H01 7/6 |
E030026 |
Ametek Gemco Seat. Main Spring Seat on a TM-3014 Brake. Item #2. 1 per brake 318B795H08 10/7 |
E030027 |
Ametek Gemco Brake Shoe & Lining Complete for a TM-30141, 30 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 426C041G01 7/6 |
E030030 |
Ametek Gemco Series Wound Coil for a TM3014 Brake. Qty 1, 2 per brake. Old Westinghouse # 645C518G16 |
E030031 |
Ametek Gemco Block. Inner Hinge Block on a TM-3014 Brake Tie Rod. Ref. #4. 1 per Brake 318B795H08 7/6 |
E030032 |
Ametek Gemco Release Bushing on a TM-3014 Brake Assembly. Item # 5, 1 per brake 318B792H08 1/7 |
E030033 |
Ametek Gemco Tie Rod on a TM-3014 Brake Assembly. Item # 6. 1 per brake. 635C104G08 7/6 |
E030034 |
Ametek Gemco Adjusting Screw Block on a TM-3014 Brake. Ref # 7 1 per brake 7/6 |
E030035 |
Ametek Gemco Screw. Adjusting Screw on a TM3014 Brake. , Item #3. 1 per Brake, 318B793H08 1/7 |
E030036 |
Ametek Gemco Wheel End Spring Seat on a TM-3014 Brake Assembly. Item # 11. 1 per brake 318B777H08 10/7 |
E030040 |
Ametek Gemco Brake Shoe Bolt on a TM-3014 Brake Assembly. Ref. # 16. 2 per brake. 450A869G01 3/6 |
E030043 |
Ametek Gemco Pin. Pivot Pin 1/7 |
E030045 |
Ametek Gemco Bushing on a TM3014 Brake 16 per brake 1/7 |
E030046 |
Ametek Gemco Clapper & Arm on a TM-3014 Brake Assembly. Ref. #22. 1 per brake. 641C792G01 3/6 |
E030047 |
Ametek Gemco Pin 1/7 |
E030050 |
Ametek Gemco Dust Seal for the coil on a TM-3014 Brake Assembly. Recommended spare part. 1 per brake 318B917H08 |
E030051 |
Ametek Gemco Spring Clip on a TM-3055 Brake Assembly. Ref # 27 2 per brake. 318B778H08 (1LB) 1/7 |
E030052 |
Ametek Gemco Tension Spring for a TM3014 30 Inch Brake. Ref. # 28. 2 per brake. Recommended spare part. 438A411H08 3/6 |
E030053 |
Ametek Gemco Pin. Tension Spring Pin on a TM3014 Brake. Ref # 29 1 per brake. 318B790H08 3/6 |
E030054 |
Ametek Gemco Brake Lining, TM3014, Old 861C691G22 |
E030055 |
Ametek Gemco Coil Leads, TM1355 thru TM3014, include lugs. Series Wound brake coils, 4 per brake ( 2 per coil) the 30 inch brake requires 8 (1LB) |
E030079 |
Ametek Gemco Series Wound Brake Coil for a TM-3014 30 Inch Brake Assembly. 2 per brake, sold individually 645C518G19 2/7 |
E030096 |
Ametek Gemco Hinge Block, Magnet End on a TM-3014 Brake Assembly. Item #1. 1 per brake 318B788H08 |
E030097 |
Ametek Gemco Hinge Block. Wheel End Hinge Block on a TM-3014 Brake. Item #12. 1 per brake. 318B787H08 7/6 |
E030101 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM3014 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
E030500 |
Ametek Gemco Brake Wheel 30 Inch Diameter Pilot Bore TM Brakes CF |
E109062 |
Ametek Gemco Coil. Series Coil for a TM1985 Brake, 2 per brake, sold each, 637C523G16 1/8 |
Enclosure CB110 NEMA 4 |
Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
Enclosure CB15 NEMA 4 |
Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
Enclosure CB160 NEMA 4 |
Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
Enclosure CB35 NEMA 4 |
Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
Enclosure CB75 NEMA 3 |
Ametek Gemco Electric Brake Enclosure. NEMA 3. Approval Drawing required. Must be ordered with brake |
Enclosure CB75 NEMA 4 |
Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
Enclosure ET-8 |
Ametek Gemco Enclosure. NEMA 3R Enclosure for a ET-8 Brake Assembly. Specifically 8210-8-4-A-S-X-X-N-I |
Enclosure NEMA 12 |
Ametek Gemco Enclosure. NEMA 12 Enclosure for all AHM Panels. 36 X 48 Inches |
Enclosure TM-1665 NEMA 4 |
Ametek Gemco Enclosure. NEMA 4 Rated Enclosure for a TM-1665 Brake assembly. Includes Brake Wheel Shaft Seals. Shaft Diameters and approval drawing are required. Enclosures must be ordered with a brake. A Thermostatically Controlled Heater is available at additional cost |
Enclosure TM83 |
Ametek Gemco Enclosure. NEMA 3R Enclosure for a TM83 Brake Assembly |
Enclosure TMSC-1035 |
Ametek Gemco Enclosure. NEMA 3R Enclosure for a TMSC-1035 Brake Assembly |
Enclosure TMSC-1355 |
Ametek Gemco Enclosure. NEMA 3R Enclosure for a TMSC-1355 Brake Assembly. Approval drawing provided, requires signature |
Enclosure TMSC-1665 |
Ametek Gemco Enclosure. NEMA 4 Enclosure for a TMSC-1665 Brake Assembly. Approval drawing provided, requires signature |
ET-10 |
Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake, 200 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 150 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal 8210104ASXXXI |
ET-10DC |
Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake, 200 LB FT, 230 VDC., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake, 150 LBS + skid |
ET-11NA |
Ametek Gemco Electro-Thrust Brake Assembly. 11 Inch Diameter, 400 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, Built to AISE specs with the exception of the increased brake torque. -13 thru 104 Degrees F. Brake Setting Times, Without the Adjusting Valve 0.75 Sec. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. With the Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching), enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal (200 LBS) |
ET-13 |
Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake, 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. or With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 250 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal |
ET-13DC |
Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake, 550 LB FT, 230 VDC,Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. or With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 250 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal |
ET-14NA |
Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter, 800 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, 320 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal |
ET-14NA DC |
Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter, 800 LB FT, 230 VDC, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 320 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal |
ET-16 |
Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake, 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. or With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 400 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal |
ET-18NA |
Ametek Gemco Electro-Thrust Brake Assembly, 18 Inch Diameter Brake, 1500 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 640 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures & strip heaters |
ET-19 |
Ametek Gemco Electro-Thrust Brake Assembly, 19 Inch Diameter Brake, 2000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. or With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 6400 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal |
ET-19NA |
Ametek Gemco Electro-Thrust Brake Assembly, 18 Inch Diameter Brake, 1600 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake, 640 LBS + skid Ships via motor freight. Options include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters. |
ET-23 |
Ametek Gemco Electro-Thrust Brake Assembly, 8210-23-4-A-S-X-X-X-I 23 Inch Diameter Brake, 4000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.27 Sec. With Adjusting Valve 0.4 to 1.7 Sec. to softly apply the brake, 875 LBS + skid. Options include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters (900LBS) |
ET-30 |
Ametek Gemco Electro-Thrust Brake Assembly, 30 Inch Diameter Brake, 9000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve TBD Sec. With Adjusting Valve TBD Sec. to softly apply the brake, 1500 LBS + skid |
ET-6NA |
Ametek Gemco Electro-Thrust Brake Assembly, 6 Inch Diameter Brake, 60 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake, (as such this brake is not suitable for hoist applications ) 120 LBS + skid., Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures & strip heaters |
ET-8 |
Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal. |
ET-8DC |
Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 VDC, Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal |
ET-8NA |
Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 160 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 1.1 Sec. With Adjusting Valve 1.5 to 7.2 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal. |
ETH-08NA-DC Brake Only |
Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 160 LB FT, 230 Volt DC Motor, Built to AISE Specifications with the exception of the brake torque which is 60 FT LB higher than AISE specifies, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times; Without Adjusting Valve 1.1 Sec. With Adjusting Valve 1.5 to 7.2 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application (165LBS) Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters |
ETH-10 Brake Only |
Ametek Gemco spring applied, electro-hydraulically released, 10 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 460 / 230 Volt AC motor. 200 FT LBS. |
ETH-10 Brake Sys DC |
Ametek Gemco Electro-Thrust Brake System with Hydraulic Cab Control. 10 Inch Diameter Brake, 200 LB FT, 230 VDC Shunt Wound Motor. Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake, hydraulic actuator for auxiliary cab control for a progressive hydraulic brake pedal actuation. System includes: Qty. 1, ET-10 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703 |
ETH-10-DC Brake Only |
Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 200 LB FT, 230 Volt DC Motor, Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times; Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters # 82300014 (165LBS) |
ETH-13 Brake Only |
Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 250 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters. |
ETH-13 Brake Only DC |
Ametek Gemco spring applied, electro-hydraulically released, 13 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 230 Volt DC Shunt Wound Motor.550 FT LBS. |
ETH-13 Brake Sys |
Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 250 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters. System includes: Qty. 1, ET-13H Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703 |
ETH-13 Brake Sys DC |
Ametek Gemco Electro-Thrust Brake System with Hydraulic Cab Control. 13 Inch Diameter Brake, 550 LB FT, 230 VDC Shunt Wound Motor. Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, hydraulic actuator for auxiliary cab control for a progressive hydraulic brake pedal actuation. System includes: Qty. 1, ET-13 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703 |
ETH-14NA |
Ametek Gemco spring applied, electro-hydraulically released brake assembly with hydraulic actuator for auxiliary manual cab control via foot pedal (sold separately). The thruster includes a 230VDC motor. The brake is set up for a 14'' diameter wheel which is not included. Two 10797 armored hose kits are included. A fluid reservoir bleeder is required, but not included. A manual hydraulic foot pedal control cylinder is required, but not included. |
ETH-14NA BO |
Ametek Gemco spring applied, electro-hydraulically released, 14 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 460 / 230 Volt AC motor. 800 FT LBS. |
ETH-16 Brake Only |
Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 400 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters |
ETH-16 Brake Only DC |
Ametek Gemco spring applied, electro-hydraulically released brake assembly with hydraulic actuator for auxiliary manual cab control via foot pedal (sold separately). 1000 LB / FT. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake.The thruster includes a 230VDC motor. The brake is set up for a 16'' diameter wheel which is not included. A fluid reservoir bleeder is required, but not included. A manual hydraulic foot pedal control cylinder is required, but not included. |
ETH-16 Brake Sys DC |
Ametek Gemco spring applied, electro-hydraulically released brake system with hydraulic actuator for auxiliary manual cab control via foot pedal. 1000 LB / FT. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake. The thruster includes a 230VDC Shunt Wound Motor. The brake is set up for a 16'' diameter wheel which is not included. System includes: Qty. 1, ETH-16 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703
|
ETH-16 Brake System AC |
Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a foot pedal. 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. System includes: Qty. 1, ETH-16 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703400 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters |
F00017 |
Ametek Gemco Gasket. Copper Gasket , used with armored hose, 33/64'' I.D. (<1LB) |
F000602 |
Ametek Gemco Gasket. Copper Gasket (<1LB) |
F000603 |
Ametek Gemco Gasket. Copper Gasket (<1LB) |
F000996 |
Ametek Gemco Plug |
F002395 |
Ametek Gemco Boot. Actuator Boot, Item 11, used on actuating cylinders J007905, J023437 & J008765 (1LB) |
F004481 |
Ametek Gemco Adapter 1 X 16 for a Disc Brake Power Cluster (-1LB) |
F006446 |
Ametek Gemco Screw. Bleeder Screw (<1LB) |
F011955 |
Ametek Gemco Adaptor Fitting, 1/2 -20 UNF Male to 1/4-18 NPTF Male, Brass (1LB) |
F020412 |
Ametek Gemco 2 Way Hydraulic Check Valve with Fittings for 1/4 Inch O.D. Copper Tubing |
F034635 |
Ametek Gemco Displacement Cylinder |
FRBKIT |
Ametek Gemco Fluid Reservoir Bleeder Kit including an AC or DC fluid reservoir bleeder assembly, a bleeder pushbutton and necessary tubing, fittings and brake fluid. |
Hand Release |
Ametek Gemco Hand Release Option. Must be ordered with brake |
HM18X8-1 |
Ametek Gemco Hydraulic Brake System. Cab controlled Type HM Brake system with Parking Brake. Qty. 18 X 8 Brake, with Type HM Control Unit and Parking Brake Control Station, Fluid Reservoir Bleeder, Bleeder Push-Button, Control Cylinder & Pedal, Armored Hoses, 150 Feet of Tubing, Fittings & Brake Fluid. Specify whether bleeder check valve is to be controlled by 230 VDC / 115 Volt AC or Manually Operated via a 90 Degree Ball Valve |
J000086 |
Ametek Gemco Nut. Brass Tube Nut for the connection of flared copper tubing joints (1LB) |
J000233 |
Ametek Gemco Brass Fastener Assembly. Bolt, Nut & Lockwasher for the 10 Inch Brake, 8 per lining
|
J000269 |
Ametek Gemco Outlet Fitting. 1/2 X 20 male thread at both ends. 1 end is for flared tubing the other end is flat like the end of the armored hose requires F17 copper gasket (<1LB) |
J000363 |
Ametek Gemco Brass Bolt, Nut & Lockwasher for 14 & 18 Inch Brake Linings, 8 per 14 Inch Lining & 14 per 18 Inch Lining (<1LB) |
J000387 |
Ametek Gemco Fastener. Brass Fastener Assembly. Bolt, Nut & Lockwasher for the 6 & 8 Inch Brake, 6 per 6 inch lining 8 per 8 Inch lining required. Ref Item 4. Sold each (<1LB) |
J000391 |
Ametek Gemco Spring Clamp Tool for air releasing cylinders. |
J001234 |
Ametek Gemco Lining. Brake Lining for a 14 Inch Hydraulic Brake. Lining has 8 Drilled & Countersunk holes for J000363 Brass Fasteners sold separately. Ref item # 23. 2 per brake. Sold each. 287DC Scan-Pak, Non Asbestos, MSDS Sheet Provided ( 7 LBS) |
J001235 |
Ametek Gemco Brake Shoe & Lining for a 14 Inch Hydraulic Brake. Bonded linings with new pin & hardware. Qty. 1, 2 per brake assembly (23LBS) |
J001276 |
Ametek Gemco Lining. Brake Lining for an 18 Inch Hydraulic Brake. Lining has 14 Drilled & Countersunk holes for J00363 Brass Fasteners sold separately. Ref item # 23. 2 per brake. Sold each. 288DC Scan-Pak, Non Asbestos, MSDS Sheet Provided ( 8 LBS) |
J001396 |
Ametek Gemco Head Gasket, Head & Barrel to Control Cylinder Seal |
J001768 |
Ametek Gemco Arm. Lever Arm on a 14 Inch Hyd brake. Ref item # 12. 1 per brake |
J001803 |
Ametek Gemco Brake Shoe & Lining for a 18 Inch Hydraulic Brake, Qty. 1, 2 per brake (35LBS) ISG CLE 1231853
|
J002395 |
Ametek Gemco Boot. Actuator Boot, Item 11, used on actuating cylinders J007905, J023437 & J008765 (1LB) |
J002398 |
Ametek Gemco Brake Base for 6 or 8 Inch Hydraulic Brake ISG SAP 1094553 |
J002680 |
Ametek Gemco Brake Base, 10 Inch Hydraulic ISG SAP 1094527 |
J002681 |
Ametek Gemco Shoe Arm, 10 Inch Hydraulic ISG SAP 1087483 |
J002682 |
Ametek Gemco Shoe Arm, 10 Inch Hydraulic ISG SAP 1087484 |
J002683 |
Ametek Gemco Base for a 2929 14 Inch Brake ISG SAP 1094535 |
J002684 |
Ametek Gemco Shoe Arm on a 14 Inch Brake, right side with provision for shoe centering lock kit ISG SAP 1087485 |
J002685 |
Ametek Gemco Shoe Arm on a 14 Inch Brake with mount for hyd. cylinder ISG SAP 1087486 |
J002686 |
Ametek Gemco 18 Inch Hyd Centering Spring |
J002779 |
Ametek Gemco Brake Assembly. 8 X 3 Inch Hydraulic Brake Assembly, 200 to 450 FT LBS (30LB) |
J002926 |
Ametek Gemco Brake Assembly. Hydraulic Brake, 10 Inch Diameter, Type H. Hydraulic Actuator and the Brake Wheel are not included (93LBS) |
J002929 |
Ametek Gemco Hydraulic Brake Assembly. 14 Inch Type H, Less Hydraulic Actuator, 0 to 600 FT LBS on a Manual Brake System. 0 to 1400 FT LBS on a Air / Hydraulic Brake System.A 14 X 6 Inch Brake Wheel is not included (161LBS) |
J002932 |
Ametek Gemco Brake Assembly, 18 X 8 Type H. Up to 900 LBS. / FT. dynamic stopping torque on a manual hydraulic brake system. 1800 LBS. / FT. dynamic stopping torque on a Air / Hydraulic brake system. 27.75 Inches Wide. 34.375 Inches high with brake applied. A hydraulic actuator and brake wheel are not included (266LBS) |
J002935 |
Ametek Gemco Base. Brake Base on an 18 Inch Hydraulic Brake. Item 26, 1 per brake (40LBS) |
J002936 |
Ametek Gemco Arm. Brake Shoe Arm on an 18 Inch Hydraulic Brake. Item 18, 1 per brake (20LBS) |
J002937 |
Ametek Gemco Arm. Brake Shoe Arm on an 18 Inch Hydraulic Brake. Item 1, 1 per brake. Arm that has the actuator (20LBS) |
J003054 |
Ametek Gemco Actuator. Type HM Hydraulic Actuator / Slave Cylinder on a 6 or 8 Inch Hyd Brake with the Parking Brake Option. Item 29A, 1 per brake (11LBS) ISG SAP 1085518 |
J003080 |
Ametek Gemco Brake Fluid Reservoir Bleeder. OBSOLETE, replaced by PSD-0180101. Includes a Solenoid Operated Valve which is controlled by a remotely mounted switch which is not included. 230 Volt DC, Fluid Capacity 2-1/3 rd Quart. Replaced by PSD0180101 (13LBS) |
J003082 |
Ametek Gemco Brake Fluid Reservoir Bleeder. OBSOLETE, replaced by PSD0180100. Ametek Gemco Brake Fluid Reservoir Bleeder. Includes a Solenoid Operated Valve which is controlled by a remotely mounted switch which is not included. 440 Volt AC, 50/60 Hz., 45VA. Fluid Capacity 2-1/3 rd Quart. Net Weight 9 LBS Replaced by PSD-0180100 110 Volt |
J003083 |
Ametek Gemco Brake Fluid Reservoir Bleeder. OBSOLETE, replaced by PSD0180100. Ametek Gemco Brake Fluid Reservoir Bleeder. Includes a Solenoid Operated Valve which is controlled by a remotely mounted switch which is not included. 110 Volt AC, 50/60 Hz., 45VA. Fluid Capacity 2-1/3 rd Quart. Net Weight 9 LBS Replaced by PSD-0180100. (ISGSAP1267689) |
J003205 |
Ametek Gemco Brake Assembly. 8 X 3 Inch Type HM Brake, 200 FT LBS Manual Operation / 450 FT LBS Air over Hydraulic Operation. HM = Spring Set Parking & Holding 50 FT LBS, includes actuator (32LBS) |
J004954 |
Ametek Gemco Brake Lining, 10 Inch Diameter, Hydraulic, drilled and countersunk for 8 brass fasteners |
J005137 |
Ametek Gemco Bushing. Tube Bushing for brake lines (<1LB) |
J005138 |
Ametek Gemco Clamp. Bushing Clamp for brake lines (<1LB) |
J005780 |
Ametek Gemco Hose Bracket for the armored hose |
J006110 |
Ametek Gemco Brake Shoe & Lining for a 10 Inch Hydraulic Brake J002926. Bonded linings with new pin & hardware Qty. 1, 2 per brake assembly (13LBS) |
J006693 |
Ametek Gemco Bushing. Knuckle Bushing on a 14 or 18 Inch Brake (1LB) ISG SAP 1111645 |
J006694 |
Ametek Gemco Eye Bolt Bushing used on a 10, 14 or 18 Inch Hyd. Brake ISG SAP 1111273 |
J006696 |
Ametek Gemco Pin on a 14 or 18 Inch Brake Assembly. Connects top of the hydraulic actuator to the lever arm.1/2 Inch Diameter X 2.375'' Long. Smallest solid pin with two holes for cotter pins. 1 per brake CMH000180 (<1LB) |
J006816 |
Ametek Gemco Pin on a 14 Inch Brake Assembly. Mounts shoes & the bottom of both brake arms. 5.875 Inch Long X 1 Inch Diameter 0.875-14 Thread. Largest Pin on the brake. 4 per brake. |
J006817 |
Ametek Gemco Pin on a 14 or 18 Inch Brake Assembly. Connects lever arm to the brake arm & lever arm to knuckle. 4.5 Inch Long X 1 Inch Diameter, .875-14 Thread, 2 per brake (1LB) |
J006818 |
Ametek Gemco Pin on the 14 or 18 Inch Brake Assembly. Connects eye bot to the brake arm. 3.5 Inch Long X 1 Inch Diameter. Smallest threaded pin in length. 1 per brake CMU0015555 (1LB) |
J006873 |
Ametek Gemco Pin on a 14 or 18 Inch Brake Assembly. Connects the bottom of the hydraulic actuator to the brake arm.Soild pin 2 holes for cotter pins. 1 per brake (<1LB) |
J006874 |
Ametek Gemco Pin on an 18 Inch Brake Assembly. 4 per brake. 2 for Brake Shoes & 2 for Brake Shoe Arms (1LB) |
J006912 |
Ametek Gemco Head & Barrel Assembly for a 1 & 3/4 Inch Control Cylinder J017616. Ref # 15 Includes items 14 thru 19. For I.D. has an ''X'' is cast into its side. 2.85'' long It is the complete hydraulic section for repair of a J017616 Control Cylinder (5 LBS)
|
J006940 |
Ametek Gemco Bushing ISG SAP 1111272 (1LB) |
J006941 |
Ametek Gemco Bushing ISG SAP 1111634 (1LB) |
J006942 |
Ametek Gemco Pin on a 10 Inch Hyd Brake. Brake Shoe & Brake Arm Pin. 4 per brake. Sold each. 4.875 Inch Long, .75 Inch Diameter, 9/16 - 18 Thread (1LB) M00034717 |
J006943 |
Ametek Gemco Pin, 3 & 5/16 Long, .75 Inch Diameter, 9/16-18 Thread, 3 on 10 Inch Brake
|
J006944 |
Ametek Gemco Spring Hook for a 10 Inch Hyd brake. Item 12 & 13, 2 per brake, same as J006945 (1LB) |
J006945 |
Ametek Gemco Spring Hook for a 10 Inch Hyd brake. Item 12 & 13, 2 per brake, same as J006944 (1LB) ISG SAP 1163102 |
J006946 |
Ametek Gemco Pin for a Hyd Actuator, Bottom, 2 & 3/8th Inches Long, secured by 2 cotter pins (1LB) |
J006953 |
Ametek Gemco Pin on a 10 Inch Hyd Brake. Top Pin thru lever, supports return springs. 3 & 7/8 Inches Long, secured by 2 cotter pins (1LB) |
J007158 |
Ametek Gemco Lever. Lever on a Control Cylinder. Main shaft to plunger on the head & barrel. Ref. Item # 5 (1LB) |
J007268 |
Ametek Gemco Yoke & Rod End, Machined, 14 & 18 Inch Brakes |
J007346 |
Ametek Gemco Plug. Adaptor Plug with Bleeder Outlet (<1LB) |
J007841 |
Ametek Gemco Actuator / Slave Cylinder on a 6 Inch J23020 or 8 Inch & J02779 Hyd Brake. Item 19A, 1 per brake. A recommended spare part (5LBS) |
J007844 |
Ametek Gemco Brake Shoe Assembly. Brake Shoe & Lining complete with bushings for J002779 or J003205 8 Inch Hydraulic Brake. Ref #2 2 per brake. Sold each (7LBS) |
J007846 |
Ametek Gemco Lining. Drilled Lining, 8 Inch Diameter for a 8 Inch Hydraulic Brake Assembly. Ref Item 3. Qty. 8 drilled & countersunk holes for brass fastener J000387 which is not included (1LB) |
J007905 |
Ametek Gemco Actuator. Hydraulic Actuating / Slave Cylinder, 1.125 Inch Diameter Bore, 3 inch Stroke. For use on a 10, 14, or 18 Inch Manual single brake system. Casting # on cylinder body 7985 (6LBS) Mittal 1085522
|
J007985 |
Ametek Gemco casting part number for a actuating / slave cylinder. Can be manufactured into three different size units. Finished part number required. J007905 - J008765 - J0023437 |
J007996 |
Ametek Gemco Rod End Assembly |
J008040 |
Ametek Gemco Lever & Bushing for a 10 Inch Hyd Brake Type HM, Item 14, 1 per brake, 2822 Lever & Bushing (11LBS) |
J008120 |
Ametek Gemco Spring Arm 10 Inch |
J008122 |
Ametek Gemco Spring, 10 Inch, Centering (1LB) |
J008124 |
Ametek Gemco 14 Inch Spring Arm (2LBS) |
J008126 |
Ametek Gemco 14 Inch Hyd. Centering Spring |
J008128 |
Ametek Gemco 18 Inch Spring Arm ISG SAP 1087054 |
J008134 |
Ametek Gemco 10 Inch Return Spring (2LB) ISG SAP 1237192 |
J008135 |
Ametek Gemco Spring. Main Return Spring for a 14 or 18 Inch Hydraulic Brake Assembly (1 LB) ISG SAP 1237193 |
J008178 |
Ametek Gemco Bushing. Obsolete by about 8 years. Bushing between pedal & control cylinder shaft. Purchase new pedal J008219 which no longer requires the bushing |
J008219 |
Ametek Gemco Pedal. Brake Pedal by 18 Inches for use on Control / Master Cylinder. Cast Iron Item # 34 (8LBS) Mittal 1197677 |
J008474 |
Ametek Gemco OBSOLETE Coil 230 Volt DC for FRB |
J008477 |
Ametek Gemco Obsolete Coil 115 Volt AC for FRB |
J008765 |
Ametek Gemco Hydraulic Actuator Actuating / Slave Cylinder, 1.125 Inch Diameter Bore, 2.5 Inch Stroke. Manufactured for P&H / Morris. Casting # on cylinder body 7985 (6LBS) |
J008905 |
Ametek Gemco Actuating Cylinder, 1.125 Inch Diameter, Brass Cylinder, Chrome Plated Parts, for corrosive environments, like 7905 Old Price |
J009391 |
Ametek Gemco Pin Guide |
J009392 |
Ametek Gemco Guide. Spring Guide on a J007841 Act Cyl. Item 20. 1 per brake (<1LB) |
J009395 |
Ametek Gemco Spring. Return Spring in a J007841 Act. Cyl. Item 18, 1 per brake,6 or 8 Inch Hyd Brake (<1LB) ISG 237196 |
J009396 |
Ametek Gemco Connecting Rod with Threaded Cap. Part of the Actuator J007841 on a 6 or 8 Inch Hyd Brake. Ref # 17, 1 per brake (1LB) ISG SAP 1218454 |
J009400 |
Ametek Gemco Cover. Slave Cylinder Cover / Sleeve on a J007841 Brake Actuator. Item 22, 1 per brake, used on a 6 Inch J23020 or 8 Inch & J02779 Hyd Brake (1LBS) |
J009431 |
Ametek Gemco Adjusting Sleeve Knuckle on a 6 or 8 Inch Hydraulic Brake. Ref. item # 14. 1 per brake |
J009637 |
Ametek Gemco Knuckle 5020 with Bushings for the 14 & 18 Inch brakes (5LBS) ISG SAP 1111277 |
J009638 |
Ametek Gemco Adjusting Nut, only available in Adjusting Nut Kit 105193, for the 14 & 18 inch brakes. |
J009668 |
Ametek Gemco Tubular Push Rod, 14'' & 18'' H Brakes |
J009672 |
Ametek Gemco Bushing |
J009674 |
Ametek Gemco Bushing |
J009677 |
Ametek Gemco Cylinder. Cylinder & boss Assembly. Cover on an Air Releasing Cylinder. Type ''S'' Brakes J023033 & J023034 (1LB) |
J009681 |
Ametek Gemco Mounting Lug (2LBS) |
J009688 |
Ametek Gemco Mounting Extension for an 18 Inch HM Cylinder |
J009704 |
Ametek Gemco Cup 1 & 1/8th Inch Diameter for use in a Hydraulic Actuator J007905 orJ008765 aka JFC-9704 (<1LB) |
J009705 |
Ametek Gemco Bleeder Screw |
J009945 |
Ametek Gemco Brass Tee Fitting. 3 outlets for 45 Degree Flared Tubing. Use tube nut 86 not included for each entrance |
J010008 |
Ametek Gemco Switch with Enclosure. Push Button for FRB operation. Oiltight surface mount enclosure with one normally open momentary contact. Includes nameplate legend for I.D. and use, 3/4 -14 conduit entrance & mounting holes for 10-32 screws (6LBS) |
J010068 |
Ametek Gemco Eye Bolt & Bushing for a 14 or 18 Inch Brake (5LBS) ISG SAP 1111274 1111275 |
J010069 |
Ametek Gemco 6939 Eye Bolt & Bushing 6940 for a 10 X 4 Inch Hyd Brake. Item # 10 1 per brake (4LBS) ISG SAP 1111271 |
J010070 |
Ametek Gemco Lever & Bushing for a 10 Inch Hyd Brake, Item 14, 1 per brake, 1291 Lever & Bushing (11LBS) |
J010071 |
Ametek Gemco Knuckle & Bushing Assembly on a 10 X 4 Type H Brake. Knuckle 6114 & Bushing J6941. Ref. item # 17. 1 per brake. 2 LBS ISG SAP 1097314 |
J010160 |
Ametek Gemco Armored Hydraulic Hose by 30 Inches Long with threaded fittings. Flexible connection between copper tubing & brake component. Connects to flared copper tubing using #86 Tube Nut and completes a connection to a hydraulic brake component using copper compression Washer #17 . Tube Nuts & Copper Compression Washers are not included see complete hose connection kit 10797 (1LB) |
J010403 |
Ametek Gemco Valve Rod on the Fluid Reservoir Bleeder, no longer available |
J010683 |
Ametek Gemco Piston. Releasing Piston Push Rod on a 3054 Actuator. item # 32 1 per brake. (1LB) |
J010685 |
Ametek Gemco Spring. Piston Cup Retaining Spring on a 3054 HM Actuator |
J010687 |
Ametek Gemco Push Rod part of a 3054 HM Actuator used on a 6 Inch Brake. Item # 31 1 per brake. (1LB) |
J010688 |
Ametek Gemco Push Rod Retaining Screw on a 3054 Actuator |
J010690 |
Ametek Gemco Piston & Setting Spring Guide in a J003054 HM Actuator 8 X 3 Brake (1LB) |
J010696 |
Ametek Gemco ''C'' Washer on a 3054 HM Actuator |
J0107017 |
Ametek Gemco Contactor 700A12NZ253 |
J010797 |
Ametek Gemco Hose. Armored Hose Kit, 30 Inch Long Hose with Copper Gasket F17, Lockwasher, Jam Nut & Angle / Frame Bracket 5780 (1LB) |
J010799 |
Ametek Gemco Repair Kit. Shaft Seal Repair Kit for a Control Cylinder (pedal side) Includes 5 Items, Items 8 to 12; O'Ring, Retainer Plate, Snap Ring, Felt Seal & Felt Retainer (1LB) |
J015555 |
Ametek Gemco Right Angle Fitting Kit (1LB) |
J015576 |
Ametek Gemco Tubing Installation Kit including 50' 5/16'' OD copper tubing, 15pcs 5137 tube bushings, 15pcs 5138 tubing clamps, 3pcs 86 tube nuts, 1pc 49087 tube union. |
J016242 |
Ametek Gemco Connector Fitting (<1LB) |
J016307 |
Ametek Gemco Obsolete 2006 see J006912, Head & Barrel Assembly with a 1 & 1/2 Inch Diameter Bore for use on a J016320 Control Cylinder (8LBS) |
J016320 |
Ametek Gemco Control Cylinder with a 1 & 1/2 Inch Diameter Head & Barrel (27LBS) |
J017611 |
Ametek Gemco Shaft. Main Shaft in a Control Cylinder, item 4, (2LBS) |
J017616 |
Ametek Gemco Control Cylinder, 1 & 3/4 Inch Diameter Head & Barrel, less pedal (27LBS) |
J017626 |
Ametek Gemco Spring Case Assembly Kit for use on any of the Control Cylinders. (broken return spring repair kit) Includes gaskets & hardware (3LBS) |
J018377 |
Ametek Gemco 2 Way Hydraulic Check Valve with flared fittings for connection with 5/16 Inch O.D. Copper Tubing ISG CMQ000186 (1LB) |
J019039 |
Ametek Gemco Obsolete 2006, though a few are still available, Repair Kit, see J006912, for a 16307 Head & Barrel Assembly used on a 16320 Control Cylinder, 1.5 Inch Bore. Includes items 14 thru 19. Valve # 14 FC-14263, Valve Seat # 14A FC-14213 = FC14426, Head & Barrel # 15 JFD-6911, Retainer Spring # 16 FC-6431, Piston Cup # 17 FD-951, Piston # 18 JFC-18362 & Support Ring # 19 FC-1960 (1LB) |
J019040 |
Ametek Gemco Repair Kit for a J006912 Head & Barrel Assembly in a J017616 Control Cylinder. 1.75 Inch Bore. Includes Items 14 to 19, FC-14426 Valve & Seat, JFD-6911 Barrel, FC-6431 Retainer Spring, FD-951 Piston Cup, JFC-18362 Piston, FC-1960 Support Ring & Item 31, J001396 Head Gasket (1LB) |
J019905 |
Ametek Gemco Cap for Control Cylinder 19907, includes breather for P&H Brake Systems |
J019907 |
Ametek Gemco Control Cylinder 1 & 3/4Inch with Special Screened Breather Cap which has a vent. J019905 Used on systems that do not have a Fluid Reservoir Bleeder and some Morris / P&H Brake Systems. For closed loop brake systems (27LBS) |
J023020 |
Ametek Gemco Brake. 6 X 3 Hydraulic Brake Assembly, 150 FT LB / Manual Foot Pedal Operation, 350 FT LB / Pnu Powered Operation, Dim. 12.625 X 10.5625 Inches (29LBS) |
J023021 |
Ametek Gemco Shoe & Lining Complete with bushings for a 6 Inch Hydraulic Brake. Qty. 1, 2 per brake assembly |
J023024 |
Ametek Gemco Brake Lining for a 6 x 3 Inch Hydraulic Brake Assembly, 1 Piece for 1 Shoe, Drilled and Countersunk for J000387 Brass Fasteners which are not included. Undrilled for bonded application are also available (<1LB) |
J023033 |
Ametek Gemco Actuator. Air Releasing Cylinder for a 10 X 4 Inch Type ''S'' Brake |
J023034 |
Ametek Gemco Actuator. Air Releasing Cylinder on a 14 X 6 Inch Type ''S'' Air Brake # 53957 |
J023437 |
Ametek Gemco Actuator. Hydraulic Actuating / Slave Cylinder, 0.875 Inch Diameter Bore, 3 Inch Stroke. For use on a 10, 14 or 18 Inch ''multi-brake'' system. Casting # on cylinder body 7985 (6LBS) |
J023447 |
Ametek Gemco Cup 7/8 Inch (<1LB) |
J024579 |
Ametek Gemco Brake Assembly. 6 X 3 Inch Type HM Brake. 150 FT LBS manual operation @ 70 LBS Foot Pressure. 350 FT LBS available with an Air Over Hydraulic brake system. HM = Brake has Spring Set Parking & Holding @ 35 FT LBS. (30LBS) |
J024684 |
Ametek Gemco Switch. Hydraulic Pressure Switch (3LBS) |
J029349 |
Ametek Gemco Air Pressure Gauge, Bottom Connection, 160 PSI (<1LB) |
J034735 |
Ametek Gemco Brake. 14 X 6 Inch Type HM Hydraulic Brake with the HM Parking Cylinder. Brake does not come with the actuating cylinder as 2 different sizes are used. (200LBS) |
J034780 |
Ametek Gemco Brake Assembly, Hydraulic Brake 10 Inch Diameter, Type HM with parking cylinder but less the slave cylinder (107LBS) |
J040065 |
Ametek Gemco 18 Inch Brake Assembly, Type HM (with parking cylinder), without actuator |
J040193 |
Ametek Gemco Solenoid Air Valve, NC, 230VDC ISG SAP 1256266 (2LBS) |
J040194 |
Ametek Gemco Solenoid Valve, NC, 115 VAC (2LBS) |
J045767 |
Ametek Gemco HM Switch & Light. Provides operator control of the magnetic check valve in the HM control unit. The green signal light is controlled by the pressure switch in the control unit. A resistor is included for 230 VDC. For systems with a parking feature |
J049087 |
Ametek Gemco Union. 1/2 X 20 male thread on both outlets for flared tubing connections (1LB) |
J053957 |
Ametek Gemco 14'' Type S Brake Assembly supplied with spring applied, air released cylinder |
J053958 |
Ametek Gemco Air Brake. Type ''S'' Air Brake 10 inch Diameter. 450 FT LBS. Spring Set / Air Released. Operates at a minimum air pressure of 60 PSI. (105 LBS) |
J054085 |
Ametek Gemco Pressure Cluster with a 1 X 5 Pressure Ratio, Air / Hydraulic. New updated / changed unit. Same fit, form & function ISG CLE SAP 1120779 ISG HEN 105836 (32LBS) |
J054086 |
Ametek Gemco Pressure Cluster with a 1 X 8 Pressure Ratio, Air / Hydraulic. New updated / changed unit. Same fit, form & function ISG HEN LA 9076 ISG CLE SAP 1008730 (30LBS) |
J058860 |
Ametek Gemco Valve. Relay Emergency Valve used on some Air over Hydraulic Brake Systems without the parking brake option. Midland Valve modified by Ametek Gemco (5 LBS) ISG SAP 1253474 |
J070806 |
Ametek Gemco Brake Fluid Res Bleeder. OBSOLETE. Manual Operation, replaced by PSD-0180102 |
J070894 |
Ametek Gemco HM Solenoid Check Valve, discontinued |
J070896 |
Ametek Gemco AH/ERC Control Panel for 230VDC operation. Includes two 8:1 pressure clusters, SSV,ESV, relay emergency valve, PS1, PS2, check valve, air pressure regulator, air gauge, dual reservoir air tank, single reservoir air tank and control interface relays ISG CEM000006 |
J070899 |
Ametek Gemco Modifier Kit 14 or 18 Inch Brake |
J070930 |
Ametek Gemco Obsolete HM Controller see J107206 new design |
J070942 |
Ametek Gemco Compressor Assembly. Includes Electric Motor, Frame & Compressor. 230/460 VAC |
J070943 |
Ametek Gemco Air Compressor Assembly, 230 VDC, .75 HP, with Oil Bath Air Filter (215LBS) ISG CLE 1264254 |
J070970 |
Ametek Gemco Panel. Brake / Motor Control Panel. AH/ERC, AC, Qty. 1, 1 X 8 Ratio Pressure Cluster, Small Panel 27 Wide X 33 Inc High |
J070971 |
Ametek Gemco Panel. Brake / Motor Control Panel. AH/ERC, AC, Qty. 1, 1 X 5 Ratio Pressure Cluster, Small Panel 27 Wide X 33 Inc High |
J070972 |
Ametek Gemco Panel. Brake / Motor Control Panel. AH/ERC, 230 Volt DC, Qty. 1, 1 X 8 Ratio Pressure Cluster, Small Panel 27 Wide X 33 Inc High |
J070986 |
Ametek Gemco A/E-ERC Control Panel for a 4 Brake System. Qty. 2, 1 X 8 Pressure Clusters DC |
J070987T002 |
Ametek Gemco Panel. AH / ERC Panel with a 5 to 1 Ratio Pressure Cluster, Volts DC, Treadle Valve (244LB) Algoma Tube |
J071023 |
Ametek Gemco AH/HRC Panel 440 VAC with Qty. 2, 1 X5 Pressure Clusters and NEMA 12 Enclosure JE70891. To work with Qty. 4, 6 X 3 Inch Hydraulic Brakes. AH/ERC = Air Over Hydraulic / Electric Remote Control |
J071030 |
Ametek Gemco Compressor / Panel Tubing Installation Kit |
J071052 |
Ametek Gemco Fittings. Adaptor, 1/2 - 20 Male & 7/16 - 24 Male (<1LB) |
J071053 |
Ametek Gemco TSRM Rectifier Kit. Used in the 107206 HM Control Unit. Obsolete as of 5/4/05 Replaced by PSD0242400 |
J073900 |
Ametek Gemco Installation Kit. Includes 50 Foot Copper Tubing, 2 Armored Hoses 30 Inch, 2 Hose Mounting Brackets, 2 Jam Nuts, 2 Lock Washers, 4 Copper Gaskets, 15 Tube Bushings, 15 Bushing Clamps, 11 Tube Nuts, 1 Tube Union & 1 Gallon Brake Fluid |
J073901 |
Ametek Gemco Installation Kit, 4 Hose 100 Ft Tubing Installation kit includes 4x30'' armored hose kits 10797, 100' of 5/16'' OD copper tubing, 35x tube bushing 5137, 35x bushing clamp 5138, 14x tube nut 86, 3x tube union 49087, 3x gal can 21B brake fluid |
J073903 |
Ametek Gemco Installation Kit. Includes 200 Foot Copper Tubing (2 X 100 FT), 4 Armored Hoses X 30 Inch, 4 Hose Mounting Brackets, 4 Jam Nuts, 4 Lock Washers, 11 Copper Gaskets, 70 Tube Bushings, 70 Bushing Clamps, 25 Tube Nuts, 6 Tube Union, 1 Tube Tee & 3 Gallons Wagner Heavy Duty Brake Fluid |
J073904 |
Ametek Gemco 6 Hose, 150 Foot Tubing Installation Kit |
J073910 |
Ametek Gemco Installation Kit. AH/ERC Tubing Kit |
J073911 |
Ametek Gemco Repair Kit for the J023437 Hydraulic Actuating Cylinder 1.125 Dia. Bore. Includes items 5 thru 11 & the boot ISG SAP 1170111 (1LB) |
J073912 |
Ametek Gemco Repair Kit for a J007905 Hydraulic Actuating Cylinder. Includes items 5 thru 9 & 11 the boot. Screw #5, Washer #6, Cup Retainer #7, Cup 1 & 1/8 Inch Diameter #8, Piston & Guide Rod Assembly #9 & Boot #11. (1LB) ISG SAP 1170112 |
J073913 |
Ametek Gemco Repair Kit for a J008765 Hydraulic Actuating Cylinder. Includes items 5 thru 9 & 11 the boot. Screw #5, Washer #6, Cup Retainer #7, Cup 1 & 1/8 Inch Diameter #8, Piston & Guide Rod Assembly #9 & Boot #11 (1LB) |
J073917 |
Ametek Gemco Repair Kit for the Old Fluid Reservoir Bleeder, now obsolete, a few left. Kit Contains: JFC10123 Valve Head & Guide, FC4540 Valve Head Gasket, JFC10126 Valve Spring, JFC10127 Valve, JFC10129 Valve Seat, JFC10128 Valve Seat Retainer, FC5227 Filler Cap, FC5228 Filler Cap Gasket, JFC10405 Valve Rod Felt Washer, JFC10406 Valve Rod Steel Washer & JFC10404 Valve Rod Return Spring. All Qty. 1. For JFF3080 7 JFF3083 (1LB) |
J073918 |
Ametek Gemco Repair Kit for a 7841 Hydraulic Actuator on a 6 or 8 Inch Brake Assembly without parking option. Includes items 21 Felt Seal 9399, 24 Piston 9390, 25 Cup 666 & 26 Cup spring 9389 (1LB) ISG SAP 1170113 |
J073919 |
Ametek Gemco Repair Kit for the 3054 HM Brake Actuator used on a 6 or 8 Inch type HM Brake. 5 Items: 9399 Felt Seal, 9517 Cup, 10681 Piston, 21334 Push Rod Seal & 10684 Cup (1LB) |
J073920 |
Ametek Gemco Pin & Bushing Kit for a 6 or 8 Inch Hyd Brake |
J073921 |
Ametek Gemco Repair Kit for a HM Cylinder J079464 on a 18 Inch Hyd Brake J400065 (1LB) |
J073922 |
Ametek Gemco Link Kit for the HM Cylinder on a 14 or 18 Inch Hyd Brake (<1LB) |
J073923 |
Ametek Gemco Spring Case Gasket Kit for use on any of the Control Cylinders. Repairs any leaks out the spring case side of control cylinder (1LB) |
J073925 |
Ametek Gemco 6242 Pin Kit (pin with hardware) replaced by 105197, 4.75 Long, .75 Dia., 2 Push Clips @ 4.25 Centers, 1 Grease Fitting |
J073926 |
Ametek Gemco Pin Replacement Kit for a 2926 & 34780 10 Inch Hydraulic Brake. 7 Pins & Hardware. New Style Pins. Requires enlargement of 1/2 of the pin holes. The old kit is back by popular demand. The new part number for the old pin kit is 73932. Change made June 1992 |
J073929 |
Ametek Gemco Pin Old Style, 18 Inch, complete with hardware, 6818 Pin |
J073930 |
Ametek Gemco Pin, old style for the 18 Inch Brake , 1 Pin complete with grease fitting, nut & lockwasher, 6874 Pin, largest pin on brake |
J073931 |
Ametek Gemco Old Pin Kit. 10 Inch Brake Shoe Pin with Nut, Lockwasher & Grease Fitting |
J073932 |
Ametek Gemco Pin Replacement Kit for a 2926 & 34780 10 Inch Hydraulic Brake. 7 Pins & Hardware. Old Style Pins for brakes before June 1992. Pins are serrated / groves and use nuts & lockwashers rather than spring clips. New style pins require old part number 73926 |
J073936 |
Ametek Gemco Old Pin Kit |
J076200 |
Ametek Gemco 6 Inch Hydraulic Brake Wheel with a Solid Hub. 6 Inch Diameter, 3.25'' Face width, 3.12'' Offset when measured from the centerline, 3'' Hub Diameter, 1/2'' Face Thickness, 4'' hub Length. Center Line is identified. Add 153.31 for finished hub, bore & keyway. 16 LBS Net. |
J076201 |
Ametek Gemco Brake Wheel. 6 Inch Hydraulic Brake Wheel with a Hub Length Bore & Keyway for a 602 Mill Motor. 6 Inch Diameter, 3.25'' Face Width, 3.12'' Offset when measured from the face centerline, 3'' Hub Diameter, 1/2'' Face Thickness, 3'' Hub Length (16LBS) |
J076225 |
Ametek Gemco 8 X 3.25 Inch Hydraulic Brake Wheel. Pilot Bore |
J076227 |
Ametek Gemco Brake Wheel 8 Inch |
J076250 |
Ametek Gemco 10 X 4.25 Inch Hydraulic Brake Wheel. Pilot Bore |
J076275 |
Ametek Gemco Brake Wheel. 14 X 6.5 Inch Hydraulic Brake Wheel. Pilot Bore |
J076277 |
Ametek Gemco Brake Wheel 14 Inch Diameter with a Hub Length Bore & Keyway for a 608 Mill Motor |
J076300 |
Ametek Gemco Brake Wheel 18 X 8.5 Inch Hydraulic Brake Wheel. Pilot Bore |
J076301 |
Ametek Gemco Brake Wheel 18 Inch with the Hub Length Bore & Keyway for a 414, 612, 812, AC25 or AC30 Mill Motor BH181005 |
J076302 |
Ametek Gemco Brake Wheel. 18 Inch Diameter. Hub Length Bore & Keyway for a 614 Mill Motor. 5.25 Inch Offset. BH181011 (240LBS) |
J076346 |
Ametek Gemco Repair Kit for 10 & 14 Inch Air Releasing Cylinders. Type ''S'' Brakes. Kit includes Items: #11, J001846 Felt Ring, #12, J1847 Piston, #13, J107010 Cup, #23, 17026 O' Ring Rod Seal, #24, 9795 O Ring Cylinder Seal, #26, 10231 Felt Washer, #27, 9691 Rod Packing Felts & #28, 23043 O Ring Rod Seal |
J078061 |
Ametek Gemco Air Pressure Switch |
J079462 |
Ametek Gemco HM Cylinder, 14 Inch Parking Cylinder (9LBS) |
J079463 |
Ametek Gemco Cylinder. HM Parking Cylinder, 10 Inch |
J079464 |
Ametek Gemco HM Cylinder,18 Inch Brake with parking (20LBS) |
J083714 |
Ametek Gemco OBSOLETE 4/6 Still a few available at BPI Repair Kit for a 54085 Pressure Cluster 1 X 5 (1LB) |
J083715 |
Ametek Gemco Obsolete 4/6 Repair Kit for a J054086 Pressure Cluster 1 X 8 Ratio ISG CLE SAP1170115 ISG HEN 1013922 (1LB) |
J087249 |
Ametek Gemco Shoe Centering Lock Kit on a 10, 14 or 18 Inch Hydraulic Brake Assembly. Ref. Item # 20. Includes 5 items: Shoe Centering Plug JFC10099, Shoe Centering Stem JFC10100, Lockwasher & Nut JFC10101. 1 per brake. |
J089662 |
Ametek Gemco A/H-ARC Large Panel 33 Inches Wide X 45 Inches High Includes 2 Pressure Clusters with an 8 to 1 Pressure Ratio, 2 Reservoirs one with Dual Compartments, Motor Control Panel with relays, Emergency Relay Valve & 2 Pressure Switches Input power can be 380, 460 or 575 Volt AC, 50 / 60 Hz |
J089664 |
Ametek Gemco Control Panel. AH-ARC Control Panel for a 2 Brake System without parking (type H), DC with 1, 8 X 1 Ratio Pressure Cluster |
J089666 |
Ametek Gemco AH-ARC Control Panel, 4 Brake, DC, 8 X 1 Ratio |
J089667 |
Ametek Gemco Brake Panel for a AH/ARC Brake System. DC with 2, 1 X 5 Ratio Pressure Clusters |
J098133 |
Ametek Gemco Actuator Seal Kit, 7/8 Inch Diameter (1LB) |
J098134 |
Ametek Gemco Actuator Seal Kit for the 1 & 1/8 Inch Diameter Actuators, J007905 & J008765. Includes items: 5 Screw, 6 Lock Washer,7 Cup Retainer J009703, 8 Cup 1 & 1/8'' J009704 & 11 Boot J002395 1 Each (1LB) |
J100650 |
Ametek Gemco AHM/ERC Panel. AC with a 54086 1 X 8 Pressure Cluster. For a 1 to 2 Brake System. |
J105190 |
Ametek Gemco Anti-Drag Kit for a 6 or 8 Inch Hyd Brake. Includes J009414 Retractor Spring, J009229 Pin, J009428 Anti-Drag Housing & J009423 Pin. Items 10, 11, 12 & 13 (3LB) ISG SAP 1169562 |
J105191 |
Ametek Gemco Clamp Nut Kit for the 6 or 8 Inch Hydraulic Brake. Includes JC9432 Adjusting Nut & JC9433 Clamp Nut. Ref # 15 & 16. 1 each per brake ISG SAP 1169651 |
J105192 |
Ametek Gemco 10 Inch Clamp Nut Kit. (ISGSAP1169648) |
J105193 |
Ametek Gemco Clamp Nut Kit for the 14 or 18 Inch Hyd. Brake. Includes item 13 -14 Clamp Nut & item 17 9638 Adjusting Nut ISG SAP 1169649 |
J105194 |
Ametek Gemco Friction Plug Kit, 10 Inch |
J105195 |
Ametek Gemco Friction Plug Kit for a 14 Inch Brake Assembly. Ref Item 6. Includes Friction Plug Spring 6528 & Friction Plugs 6689 |
J105196 |
Ametek Gemco Friction Plug Kit for a 18 Inch Brake Assembly. . Ref Item 6. Includes Friction Plug Spring 6528 & Friction Plugs 6876 |
J105197 |
Ametek Gemco Pin Kit. Hinge Pin Kit for a 10 Inch Hyd. Brake. New pin design from June 1992. Spring Clipped Pins not threaded like the old style. J105200 for brakes older than 1992 (14LBS) |
J105198 |
Ametek Gemco Pin Kit. Hinge Pin Kit for a 14 Inch Hyd Brake. New pin design from June 1992. Spring Clipped Pins not threaded like the old style. J105201 for brakes older than 1992 (17LBS) |
J105199 |
Ametek Gemco Pin Kit. Hinge Pin Kit for a 18 Inch Hyd Brake. New pin design from June 1992. Spring Clipped Pins not threaded like the old style. J105202 for brakes older than 1992 (18LBS) |
J105200 |
Ametek Gemco Pin Kit. Hinge Pin Kit for a 10 Inch Hydraulic Brake. Older style with Threaded & Serrated Pins, Nuts, Lockwashers & Grease Fittings (15LBS) |
J105201 |
Ametek Gemco Pin Kit. Hinge Pin Kit for a 14 Inch Hyd. Brake. Older style 1996 and older with Threaded & Serrated Pins, Nuts, Lockwasher & Grease Fittings. Includes Pins # 1 6873, 1 6818, 4 6816, 1 6696, 2 6817 (18LBS) |
J105202 |
Ametek Gemco Pin Kit. Hinge Pin Kit for a 18 Inch Hydraulic brake. Older Style with Threaded & Serrated Pins, Nuts, Lockwasher & Grease Fittings. 1996 Brakes and older. Includes Pins # 1 6873, 1 6818, 4 6874, 1 6696, 2 6817 (20LBS) ISG 1169845 |
J105376 |
Ametek Gemco Gasket. Copper Gasket FC17 Package of 25 Pieces (<1LB) |
J105377 |
Ametek Gemco Cap / Gasket kit for a Control Cylinder. Cap # 24693 & Gasket 12077 (1LB) |
J105378 |
Ametek Gemco Cap / Gasket Kit for a Fluid Reservoir Bleeder. Cap # FC5227 & Gasket FC5228 (1LB) |
J105379 |
Ametek Gemco Filler Cap. Tapped Cap & Gasket. drilled and tapped for fitting. Note: the fitting the cap is tapped for is not included. |
J107017 |
Ametek Gemco Contactor |
J107019 |
Ametek Gemco Relay Control, 4 Pole, 2 NO & 2 NC 250 VDC Alan Bradley. (ISGSAP1121022) |
J107039 |
Ametek Gemco Treadle Valve. Foot Operated Treadle Valve to Control A/H Brake Systems. Old # JE57159 (14LBS) |
J107040 |
Ametek Gemco Repair Kit. seal kit for the 107039 Treadle Valve Assembly (Pneu Foot Valve) (<1LB) |
J107043 |
Ametek Gemco Quick Release Valve |
J107047 |
Ametek Gemco HRC Hydraulic Remote Controlled Valve. Old AE56301 (4LBS) |
J107057 |
Ametek Gemco Motor. Air Compressor Motor, 230 Volt DC, 3/4 HP (52LBS) 1/7 |
J107065 |
Ametek Gemco Power Cluster less check valve |
J107081 |
Ametek Gemco Repair Kit. Seal Kit for HRC Valve J107047. Old # A39222 Includes the piston O'Ring & Piston Cup Seal (<1LB) |
J107084 |
Ametek Gemco Valve. Moisture Ejection Valve for air reservoirs (2 LBS) ISG 1253475 |
J107115 |
Ametek Gemco Brake Wheel 10 Inch Diameter. Steel |
J107128 |
Ametek Gemco Restricter Valve |
J107148 |
Ametek Gemco Solenoid Valve used on a HM Brake System (1LBS) |
J107151 |
Ametek Gemco Solenoid Check Valve Assembly. ( includes 107148) |
J107155 |
Ametek Gemco Conversion Kit for a HM Control Unit, Modifies obsolete existing design J070930 or J107154 to the current design J107206. Includes resistor, washers, fittings & hose. Also requires 107151 Solenoid Valve Assembly ordered separately. |
J107163 |
Ametek Gemco Pressure Cluster for long static fluid lines. Obsolete, replaced by J054086 which now handles the longer lines from the FRB |
J107206 |
Ametek Gemco Control Unit. HM Controller for a manual hydraulic brake system with a parking brake feature (33LBS) |
J107215 |
Ametek Gemco Complete Rebuild Kit for a 16320 (1LB) |
J107232 |
Ametek Gemco AHM/ERC Conversion System. AC, Qty. 4, 8 to 1 Pressure Clusters, includes special sub panel and piping |
J107930 |
Ametek Gemco Obsolete, to modify this no longer supported HM Control Unit to a 107206 the current HM Control Unit, order 107155 Kit & 107151 Solenoid Valve Assembly. |
JE76278 |
Ametek Gemco Brake Wheel 14 Inch Diameter. Hub length bore and keyway for a 606 Mill Motor, BH141007, 6360B27 (140LBS) |
LDT Repair |
Ametek Gemco LDT Bench Charge to determine condition / faults. The bench charge is waved with repair authorization |
M0074400 |
Ametek Gemco Shaft. Main Shaft on a 2000 Series Limit Switch with a NEMA 4 or 7 Enclosure |
M0074500 |
Ametek Gemco Shaft. Main Shaft on a 2000 Series Limit Switch with a NEMA 4 or 7 Enclosure |
M0074600 |
Ametek Gemco Shaft. Main Shaft on a 2000 Series Limit Switch with a NEMA 4 or 7 Enclosure 100 to 1 Ratio (<1LB) 7/7 |
M0074700 |
Ametek Gemco Shaft. Main Shaft on a 2000 Series Limit Switch with a NEMA 1 or12 Enclosure |
M0085600 |
Ametek Gemco Sprocket 40 Tooth. 1/2 Inch Single. Requires # 25 Drive Chain |
M0086600 |
Ametek Gemco Sprocket. 36 Tooth. 3/4 Inch Single. Works with Chain Sizes #35 (1LB) |
M0187700 |
Ametek Gemco Shaft. Input Shaft to the Internal Gear reducer (1LB) |
M0195500 |
Ametek Gemco Main Shaft on a 1980 Series Cam Box with 2 to 3 Circuits (2LBS) 9/4 |
M0195900 |
Ametek Gemco Main Shaft on a 1980 Series Cam Box with 13 to 16 Circuits 3/7 |
M0213800 |
Ametek Gemco Main Shaft on a Dual Extension 1980 Series Cam Box with 6 to 8 Circuits (4LBS) 10/6 |
M0213900 |
Ametek Gemco Main Shaft on a Dual Extension 1980 Series Cam Box with 12 Circuits (5LBS) 01/07 |
M0299700 |
Ametek Gemco Spring. Main Torsion Spring for a for a 909 Kam-Way Linear Limit Switch and the obsolete 917 Cycle-Set. .062 Thick , 0-48'', T/T Units (2LBS) |
M0352900 |
Ametek Gemco Spring, Main Spring Assembly for a Linear Cable Reel. A1 and A2 Style Units |
M0466500 |
Ametek Gemco Cam / Main Shaft on a Series 1980-2718 Rotating Cam Limit Switch. 7 to 8 Circuit / Cam (3LBS) |
M0551100 |
Ametek Gemco Shaft. Special Main Shaft for a 1980-3145 Limit Switch |
M0551200 |
Ametek Gemco Main Shaft for a Rotary Cam Limit Switch, 6 circuit, Add-A-Cam, 1980-3146 1980-3006 (3LBS) |
M0748600 |
Ametek Gemco Bracket. ''L'' Bracket for an LDT Head. Non Ferrous Stainless Steel. This bracket is also included in Mounting Kit 949003 (1LB) |
M0750500 |
Ametek Gemco Spacer.Magnet Spacer (<1LB) |
M082240 |
Ametek Gemco Spacer. Four Hole Magnet Spacer. Non-Ferrous Spacers should be used where the magnet will be mounted into a ferrous metal surface (<1LB) |
NP0011300 |
Ametek Gemco Nameplate |
P0005000 |
Ametek Gemco Cover for a 2000 Series Geared Rotary Limit Switch |
P0005001 |
Ametek Gemco Cover. Cover only for a Series 2000-809 HD LS, NEMA |
P0034600 |
Ametek Gemco Tool. Timing & Dwell Adjustment Tool for 1980 Series Cams. P-346-B (<1LB) |
P0078600 |
Ametek Gemco Diaphragm on a 1025D Switch. Item #6, 1 per switch (<1LB) 1/8 |
P0078800B |
Ametek Gemco Cam Block on a 1025-C Foot Switch |
Panel |
Ametek Gemco AH/ERC Panel |
PLSIO-D-16-XX-8-X |
Ametek Gemco / Allen Bradley I/O Module PLSIO-D-16-XX-8-X D = Din Rail Mounting 16 = Qty. 16, D.C. Output Relays XX = Qty. 0, A.C. Output Relays 8 = Qty. 8, D.C. Input Relays X = Qty. 0, A.C. Input Relays (5LBS) |
PM0009600 |
Ametek Gemco Cam with 270 Degrees of Dwell on a Series 2000 Spur Gear Type Switch (<1LB) 5/7 |
PM0020500 |
Ametek Gemco Enclosure with Column Insert & Bearings |
PM0020505 |
Ametek Gemco Enclosure |
PM0075601 |
Ametek Gemco Cam / Main Shaft with provisions for Tach Generator & Resolver Assembly |
PM0139600 |
Ametek Gemco Arm. Outer Shoe Arm on a ET13 Brake. 1 Pair. Item 4 4/7 |
PM0170000 |
Ametek Gemco Brake Shoe for a ET-14 Brake. 14'' Each 2 per brake |
PM0170401 |
Ametek Gemco Tie Rod for a ET-14NA Brake |
PM0176601 |
Ametek Gemco Block on a ET14NA Brake |
PM0189003 |
Ametek Gemco Shaft. Main Shaft on a 1980 Series Cam Box with Single Extension, 9 to 12 Circuits and a Straight Drive Gear Reducer. .375'' X 6.20'' 10/6 |
PM0190000 |
Ametek Gemco Main Shaft |
PM0219400 |
Ametek Gemco Cam. Special Cut Cam at 200 Degrees. Tag ''MC'' # 7605272-1 (<1LB) |
PM0219500 |
Ametek Gemco Cam. Special Cut Cam at 285 Degrees. Tag ''Nixie'' # 7605272-2 (<1LB) |
PM5188503 |
Ametek Gemco Shaft. Main Shaft on a 1980-412 with Straight Gear Reducer |
PSD0090400 |
Ametek Gemco Cam. 25 Degree Lobe, 2006 Series Switch Cam. This is the Standard Issue Cam |
PSD0091600 |
Ametek Gemco Case & Shaft Assembly on a 2006 Type ''K'' 2 Circuit RLS with a 30 to 1 Ratio (2LBS) |
PSD0091800 |
Ametek Gemco Case & Shaft Assembly on a 2006 Type ''K'' 2 Circuit RLS with a 60 to 1 Ratio (2LBS) |
PSD0093000 |
Ametek Gemco Case & Shaft Assembly on a 2006 Type ''K'' 4 Circuit RLS with an 80 to 1 Ratio (2LBS) |
PSD0093100 |
Ametek Gemco Case & Shaft Assembly on a 2006 Type ''K'' 4 Circuit RLS with a 120 to 1 Ratio (3LBS) |
PSD0094100 |
Ametek Gemco Cam Block & Worm Gear Assembly on a 2006 Type ''K'' 4 Circuit RLS with a 80 to 1 Ratio (2LBS) |
PSD0094200 |
Ametek Gemco Cam Block & Worm Gear Assembly on a 2006 Type ''K'' 4 Circuit RLS with a 120 to 1 Ratio (2LBS) |
PSD0098100 |
Ametek Gemco Shaft. Worm Shaft (1LB) 4/7 |
PSD0102500 |
Ametek Gemco Sheave Assembly, Vertical for a Linear Cable Reel |
PSD0102600 |
Ametek Gemco Sheave Assembly, Horizontal for a Linear Cable Reel |
PSD0102900 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 150 Degree Lobe / Dwell (<1LB) |
PSD0104500 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 54 Degree Lobe / Dwell (<1LB) |
PSD0105100 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 45 Degree Lobe / Dwell (<1LB) |
PSD0109200 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 30 Degree Lobe / Dwell (<1LB) |
PSD0109300 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 270 Degree Lobe / Dwell (<1LB) |
PSD0110200 |
Ametek Gemco Switch. Semelex II Manual Start Switch Set. 1 - Normally Open (NO) Switch Assembly. 1 - Normally Closed (NC) Switch Assembly |
PSD0115600 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 290 Degree Lobe / Dwell (<1LB) |
PSD0115700 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 220 Degree Lobe / Dwell (<1LB) |
PSD0115800 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 85 Degree Lobe / Dwell (<1LB) |
PSD0120700 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 180 Degree Lobe / Dwell (<1LB) |
PSD0129100 |
Ametek Gemco Cam. Special Cam for the 2006 Limit Switches. 50 Degree Lobe / Dwell (<1LB) |
PSD0139805 |
Ametek Gemco Thruster Assembly. Electro-Thrust Actuator 300N, 230 / 460 VAC, With Setting Valve, with X-Fluid. (Standard Transformer Fluid) ET-8 |
PSD0139807 |
Ametek Gemco Thruster Assembly. Electro-Thrust Actuator 300N, 230 / 460 VAC, With Out Setting Valve, with X-Fluid. (Standard Transformer Fluid) ET-8 & ET10 Brakes 6/6 2 to 4 weeks to ship FOB Peck MI |
PSD0139809 |
Ametek Gemco Thruster Assembly. Electro-Thrust Actuator, 300N, 460 VAC, Set Valve, Silicone Fluid for ET8 or ET10 Brake |
PSD0146500 |
Ametek Gemco Repair Kit. Repair / Seal Kit for a PSD0151705 Thruster Assembly. Item 8A Seals, O'Rings & Bearings 4/7 |
PSD0147005 |
Ametek Gemco Thruster Assembly. Electro-Thrust Actuator for an ET brake Assembly. 900 Newtons, 460 VAC, Set Valve included |
PSD0147119 |
Ametek Gemco Thruster Assembly. Electro-Thrust Actuator for an ET Brake Assembly. 1200 Newtons, 230 / 460 VAC, Timing / Set Valve is not included |
PSD0147205 |
Ametek Gemco Thruster Assembly. Electro-Thrust Actuator, 3200 Newtons, 460 Volt AC, Set Valve, X-Former |
PSD0147219 |
Ametek Gemco Thruster Assembly. Electro-Thrust Actuator, 3200 Newtons, 230 Volt AC, No Timing Delay / Set valve, Transformer Fluid |
PSD01495 |
Ametek Gemco Brake Shoe. Brake Shoe Assembly with Bonded Lining. 11 Inch for ET-11NA Brake |
PSD0151705 |
Ametek Gemco Thruster Assembly. 230 VDC, 500 N, for use on a ET10 Brake |
PSD0165805 |
Ametek Gemco Thruster Assembly. 460 VAC, 700 N, set Valve, Transformer Fluid |
PSD0165807 |
Ametek Gemco Thruster Assembly. 460 VAC, 700 N, Set Valve, Transformer Fluid |
PSD0172100 |
Ametek Gemco Brake Enclosure, NEMA 3R, for a ET10 & ET11 Brake |
PSD0173200 |
Ametek Gemco Thruster. Thruster Assembly for an ET-13 Brake Assembly, Explosionproof, 460 Volt AC, 700 N |
PSD0179900 |
Ametek Gemco Valve & Solenoid Assembly 120 Volt AC 50 / 60 Hz. Used on the new style Fluid Reservoir Bleeder PSD-0180100 |
PSD0179901 |
Ametek Gemco Valve & Solenoid Assembly 240 VDC used on the new style Fluid Reservoir Bleeder PSD-0180101 (3LBS) |
PSD0179902 |
Ametek Gemco Valve. Manual Valve on a F.R.B. / Fluid Reservoir Assembly PSD0180102 (2LBS) |
PSD0180100 |
Ametek Gemco Brake Fluid Reservoir / Bleeder. ''FRB'' Includes a Solenoid Operated Check Valve which is controlled by a remotely mounted switch. The momentary switch J01008 is not included. 110 Volt AC, 50 Hz. / 120 Volt AC 60 Hz., 45VA. 2.25 Qt., 1/2 Inch Conduit entrance, 1000 PSI. 2-1/3 Quart Capacity. Has replaced obsolete J003083 (13LBS) |
PSD0180101 |
Ametek Gemco Brake Fluid Reservoir / Bleeder. ''FRB'' Includes a Solenoid Operated Check Valve which is controlled by a remotely mounted switch. The momentary switch J01008 is not included. 230 Volt DC, 45W. 2.25 Qt., 1/2 Inch Conduit entrance, 1000 PSI. 2-1/3 Quart Capacity. Has replaced obsolete J003080 (13LBS) |
PSD0180102 |
Ametek Gemco Brake Fluid Reservoir / Bleeder. ''FRB'' With a manually operated Check Valve. 2.25 Qt., 1000 PSI. 2-1/3 Quart Capacity. Has replaced obsolete J070806 (13LBS) |
PSD0182605 |
Ametek Gemco Thruster Assembly. Actuator, 230 Volt DC, with Setting Valve & Transformer Fluid |
PSD0194909 |
Ametek Gemco Thruster Assembly |
PSD0205100 |
Ametek Gemco Rectifier Assembly for a 1 or 2, TM-43 through TM-1985 Brake Assemblies. A NEMA 4 Enclosure is supplied. 16.0'' H X 14.00'' W X 8.0'' D. An open chassis unit is available at less cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages. This panel includes a Special Pneumatic Relay for US Gypsum (52LBS) |
PSD0232100 |
Ametek Gemco Bracket. 1986 F/G/GG Resolver Mounting Bracket, 90 Degrees 1/8 |
PSD0242400 |
Ametek Gemco TSRM Rectifier with Resistor. Direct Replacement for J071053 TSRM Rectifier Kit used in the 107206 HM Control Unit |
PSD0245400 |
Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM43 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
PSD1147005 |
Ametek Gemco Electro-Thrust Actuator 900N 460 VAC S Valve X-Form |
PSD70147207 |
Ametek Gemco Thruster Assembly. Electro-Thrust Actuator on a ET-19 Brake Assembly, 460 VAC, 3200 N, 460 VAC., 3 Ph., 60 Hz |
Recalibration |
Ametek Gemco Recalibration of a Semelex Safetimeter |
S0005500 |
Ametek Gemco Cam. S-55-A Standard 25 Degree or 335 Degree Cam for a 2000 Series Rotary Limit Switch. |
S0005700 |
Ametek Gemco Gasket. Cover Gasket, NEMA 1, 2000 Series, 2000-809. with cover P0005001 |
S0006800 |
Ametek Gemco Cam. S-68-A Special 54 Degree or 306 Degree Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0006900 |
Ametek Gemco Cam. S-69-A Special 90 Degree or 270 Degree Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0007000 |
Ametek Gemco Cam. S-70-A Special 180 Degree Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0007100 |
Ametek Gemco Cam. S-71-A Special 240 Degree or 120 Degree Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0008400 |
Ametek Gemco Cam. S-84-A Special 75 Degree or 285 Degree Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0008500 |
Ametek Gemco Cam. S-85-A Special 105 Degree or 255 Degree Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0008600 |
Ametek Gemco Cam. S-86-A Special 135 Degree or 225 Degree Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0008700 |
Ametek Gemco Cam. S-87-A Special 150 Degree or 210 Degree Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0012600 |
Ametek Gemco Cam. 60 Degree Cam for the 2000 Series Limit Switches |
S0012700 |
Ametek Gemco Cam. S-127-A Special 360 Degree Blank Cam for a 2000 Series Rotary Limit Switch. Or if ordered installed in a Rotary Limit Switch add $ 8.00 per circuit. |
S0032400 |
Ametek Gemco Cam. Special 120 Degree Cam for a 2000 Series Rotary Limit Switch |
S00455000 |
Ametek Gemco Gasket for a 1980 NEMA 9, 8 Circuit Enclosure |
S0052100 |
Ametek Gemco Disc. Stainless Steel Pulse Generating Disc for the 1983 Opto-Cam Limit Switch. 2 Degree Increment. 1 on 1 off (<1LB) |
S0052200 |
Ametek Gemco Disc. Stainless Steel Pulse Generating Disc for the 1983 Opto-Cam Limit Switch. 4 Degree Increment. 1 on 1 off (<1LB) |
S0052300 |
Ametek Gemco Disc. Stainless Steel Pulse Generating Disc for the 1983 Opto-Cam Limit Switch. 8 Degree Increment. 1 on 1 off (<1LB) |
S0053000 |
Ametek Gemco Disc. Stainless Steel Pulse Generating Disc for the 1983 Opto-Cam Limit Switch. 1 & 1/2 Degree Increment (<1LB) |
S04581005 |
Ametek Gemco Spring on a 1025D Foot & Palm Switch Item 12 (<1LB) 1/8 |
S0D0508200L15 |
Ametek Gemco Cable. Resolver Cable with a straight connector. 15 Feet Long. Other lengths available add $ 2.00 / Foot over 15 feet |
SD-302-B |
Ametek Gemco Gear Assembly for a 2000 Series Worn Gear Limit Switch, 2000 to 1 Ratio with S55 Cams & Cam Block (4LBS) |
SD0012500 |
Ametek Gemco Latch Kit. Toggle Latch Kit. 1980 NEMA 4 Latch kit includes front & back latch of an enclosure. Plated Steel. |
SD0030200 |
Ametek Gemco Gear Assembly for a 2000 Series Worn Gear Limit Switch, 2000 to 1 Ratio with S55 Cams & Cam Block (4LBS) |
SD0114000 |
Ametek Gemco Cam Assembly. Blank Replacement Cam. Shape of the cam can be complete by end user, OEM or at additional cost by Gemco. ( a drawing must be provided ) Assembly includes 2 cams P0027100 |
SD0117800 |
Ametek Gemco Cam Assembly. Standard Replacement Cam. Assembly Made up from cams P0035600 & P0035700 includes 2 Roll Pins for installation. Mold # P.268.B (<1LB) |
SD0117900 |
Ametek Gemco Cam Assembly 180 Degree |
SD0119500 |
Ametek Gemco Bearing Assembly. Center Bearing Assembly on a 1980 Series Cam Limit Switch |
SD0132000 |
Ametek Gemco Socket Assembly. Plug-In Socket Assembly. D.P.D.T. Does not include switch (<1LB) |
SD0134500 |
Ametek Gemco Socket Assembly. Plug-In Socket Assembly. S.P.D.T. Does not include switch (<1LB) |
SD0148400 |
Ametek Gemco Tape Assembly for a 909 Kam-Way Linear Limit Switch, item 63 |
SD0148400L96 |
Ametek Gemco Tape Assembly for a 909 Series Kam-Way Linear Limit Switch. 96 Inch total length for use on a Series 909 with a 66 Inch active stroke |
SD0148700 |
Ametek Gemco Gear Train Assembly Tape Drive for a 909 Kam-Way Linear Limit Switch with 24 Inches of Total Travel, 2 to1 Ratio (4LBS) |
SD01533066L200 |
Ametek Gemco Cable by 200 Feet. High Temp 200 Degree C |
SD0157100 |
Ametek Gemco Roller Follower Assembly. Limit Switch Roller Follower. Mounts between the cam & switch increasing switch life on 1980 Series Cam Box. Can be added to cam box's that did not have this past option, now standard equipment. a.k.a. P-518-B & P-520-B (<1LB) |
SD0164000 |
Ametek Gemco Cam Assembly. Special blank cam with ''minimum dwell'' Wit-O-Matic Cam (1LB) 3/7 |
SD0168100 |
Ametek Gemco Cam Assembly. Cam for 1997 Gate Hoist Limit Switch. New undated part (August 1993), smaller diameter 6 Inch, used in conjunction with new switch bracket C035800 to compensate for the smaller diameter cams. Cam & bracket update requires replacement of all cams. All cams must be same diameter (1LB) |
SD0176100 |
Ametek Gemco Latch Kit. Toggle Latch Kit. 1980 NEMA 4 Latch kit includes front & back latch of an enclosure. Stainless Steel Components. |
SD0194800 |
Ametek Gemco Electronic Pulse Generating Switch (1LB) |
SD0195800 |
Ametek Gemco Module. Add-On, Brake Monitor Module Assembly. NEMA 1 Enclosure with cover & shaft |
SD0197700 |
Ametek Gemco Disc. Optical Pulse Disc for 1980 Series RCS. 1 Degree Split. Add-A-Cam (1LB) |
SD0201200 |
Ametek Gemco Cable Assembly for a 909 Kam-Way Linear Switch. 16.5 Inches Long plus the Travle of the Limit Switch 1/8 |
SD0203000 |
Ametek Gemco Cam. Special 15 Degree Cam for 1980 Series Cam Box (1LB) |
SD0203100 |
Ametek Gemco Cam. Special 75 Degree Cam for 1980 Series Cam Box (1LB) |
SD0207500 |
Ametek Gemco Cam. Special Cam 1/2 Circuit Right Hand 40 Degrees. Cam for 1980 Series Cam Box (1LB) |
SD0213300 |
Ametek Gemco NEMA 1 Enclosure with Cover & Shaft |
SD0231200 |
Ametek Gemco Cam. Micro Adjust Cam Assembly for 1983 Optical Coupler Rotating Cam Limit Switch (<1LB) |
SD0261908 |
Ametek Gemco Sprocket Assembly. Sprocket Assembly on a 1997 Gate Hoist Limit Switch. 15 Tooth Steel Gear. Includes items 1 through 6 on Drawing SD2619 (2LBS) |
SD0274200 |
Ametek Gemco Switch, 12 Volt, Optical Sensor for a 2052 / 1997 Motion Detector 1/8 |
SD0284100L15 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver & a 1988 PLS. This cable is 15 Feet long with Straight Connectors. Cable are sold in 1 foot increments. Please specify length under 15 foot and if over 15 foot specify length and add $ 2.00 per foot over 15 feet (2LBS) |
SD0284100L20 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver & a 1988 PLS. This cable is 20 Feet long with Straight Connectors. Cables are sold in 1 foot increments. Please specify length under 20 foot and if over 20 foot specify length and add $ 2.00 per foot over 20 feet (2LBS) |
SD0284100L25 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver & a 1988 PLS. This cable is 25 Feet long with Straight Connectors. Cables are sold in 1 foot increments. Please specify any length over 25 foot and add $ 2.00 per foot (3LBS) |
SD0284100L30 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver & a 1988 PLS. This cable is 30 Feet long with Straight Connectors. Cable are sold in 1 foot increments. Please specify length under 30 foot and if over 30 foot specify length and add $ 2.00 per foot over 30 feet (3LBS) |
SD0284100L60 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver & a 1988 PLS. This cable is 60 Feet long with Straight Connectors. Cable are sold in 1 foot increments. Please specify length under 60 foot and if over 60 foot specify length and add $ 2.00 per foot over 60 feet (6LBS) |
SD0284200 |
Ametek Gemco Resolver Single Turn Replaces SD2842C. Same as 1986A1XRX Series 1986 Industrial Duty Inline Resolver A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max (6LBS) |
SD0284200-R40 |
Ametek Gemco Resolver. Foot Mount Resolver with a 40 to 1 Ratio, Right Angle Gear Reducer. Shaft Location to be determined |
SD0284200-R50-R1 |
Ametek Gemco Resolver |
SD0284200-S30-R |
Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver model SD0284200-S30-R A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 SD = Straight Drive Gear Reducer 30 = 30 to 1 Gear Ratio R = Shaft on Right Side 1/8 |
SD02842C-R12-R6 |
Ametek Gemco Resolver. Foot Mount with a Right Angle Gear Box. Gear Ratio 12 to 1 with an R6 Shaft Location. |
SD02842C-R4.75-R6 |
Ametek Gemco Resolver. Foot Mount with a Right Angle Gear Box. Gear Ratio 4.75 to 1 with an R6 Shaft Location. |
SD0295500L15 |
Ametek Gemco Cable Assembly. Single turn resolver to I/O module with right angle connector. Other lengths available add $ 2.50 per foot over 15 |
SD0296000 |
Ametek Gemco Connector Assembly 07 Pin Female (<1LB) |
SD0296001 |
Ametek Gemco Connector Assembly 07 Pin Female. For a gasketed connection. |
SD0308900 |
Ametek Gemco Resolver. Replacement resolver with wire leads & 5 Pin Amphenol Connector (2LBS) Size 11 Single Shaft Deltran PT-Harowe # 11BRCX-300-L10/6 HAROSYN-RCX |
SD0310700 |
Ametek Gemco Switch. 1983 Low Power Optical Switch 3 to 30 VDC with isolated outputs 100 mA Max. - 2 Circuits. PCB Assembly. Coated. Switch Output Option L1 SD-3107-C (<1LB) |
SD0312400 |
Ametek Gemco Switch. Series 1983 High Power Optical Switch with Provisions for Opto 22 Solid State Relay - 2 Circuits. Switch Output Option L1 (<1LB) |
SD0312500 |
Ametek Gemco Switch Type A Opto AC Plug-In Relay 120 Volt AC at 3 AMPS RMS, I/O Module 24 - 280 VAC 3.5 Output (<1LB) |
SD0312600 |
Ametek Gemco Relay. Opto 22 DC Plug-in Relay 0-60 Volts DC at 3 Amps RMS (>1LB) |
SD0312900 |
Ametek Gemco Transducer Remote Readout |
SD0315100 |
Ametek Gemco Gear Reducer / Base Plate with Right Angle Mount with a 40 to 1 Gear Ratio. 2006 4 Circuit LH 90 Degree. Existing 2006 Limit Switches will require a machined hole, cross drilled, in the end of the main shaft & a roll pin for this addition. This base plate works only works with LEFT HAND units ( 5LBS) 1/7 |
SD0315400 |
Ametek Gemco Gear Reducer / Base Plate with Right Angle Mount with a 40 to 1 Gear Ratio. 2006 2 Circuit 90 Degree. Existing 2006 Limit Switches will require a machined hole, cross drilled, in the end of the main shaft & a roll pin for this addition. This base plate works only works with LEFT HAND units ( 4LBS) 1/7 |
SD0316600 |
Ametek Gemco Post & Plate Assembly on a 1025D Foot & Palm Switch. Item 10 (<1LB) |
SD0317200 |
Ametek Gemco Cover. Cover & Gasket for a 1025 Foot Switch |
SD0317700 |
Ametek Gemco Cover for a 1025-B Switch. Designation ''S'' Treadle Shield provides Top & Side protection. Includes Screws & Gaskets (5LBS) |
SD0334200L15 |
Ametek Gemco Cable Assembly for a single turn resolver. L15 is priced for lengths up to 15 Feet. For shorter lengths correct number for lengths longer than 15 feet add $ 2.00 / FT and correct number |
SD0334900L15 |
Ametek Gemco Display. Remote Serial 8 Digit Display. For use with 1989 Quik-Set III with Option ''R'' Includes 25 feet of cable 2 conductor shielded cable part SD0300800L25 (add $3.00 / foot for lengths over 15 feet) |
SD0334900LXX |
Ametek Gemco Cable Assembly. Dual Resolver to Programmer. Up to 15 feet at quoted cost. Each additional foot after 15 add $ 3.00 List required length in feet at end of part number |
SD0343500 |
Ametek Gemco Display. Remote Serial 8 Digit Display. For use with 1989 Quik-Set III with Option ''R'' Includes 25 feet of 2 conductor shielded cable part SD0300800L25 (add $2.00 / foot for lengths over 25 feet) |
SD0364000 |
Ametek Gemco Resolver. NEMA 4 Resolver with a 0.375 Inch Input shaft & a 2.06 Inch Hole Pattern
|
SD0365900L15 |
Ametek Gemco Cable & Connector Assembly. 13 Pin Female for 1986 Multi-Turn Resolver to I/O Module with 90 Degree Right Angle Connector. 15 Feet Long. Add $ 3.00 / Foot for additional length over 15 FT |
SD0365900L30 |
Ametek Gemco Cable & Connector Assembly. 13 Pin Female for 1986 Multi-Turn Resolver to I/O Module with 90 Degree Right Angle Connector. 30 Feet Long. Add $ 3.00 / Foot for additional length over 30 FT |
SD0365900L50 |
Ametek Gemco Cable & Connector Assembly. 13 Pin Female for 1986 Multi-Turn Resolver to I/O Module with 90 Degree Right Angle Connector. 50 Feet Long. Add $ 3.00 / Foot for additional length over 50 FT |
SD0367801 |
Ametek Gemco Resolver. Single Turn, Face Mount with coupling. 4 LBS Gross |
SD0370200 |
Ametek Gemco Mating Connectors |
SD0372700-R-2-R1 |
Ametek Gemco Resolver. Special Resolver with a Right Angle Gear Box 4/7 4 Weeks |
SD0382900 |
Ametek Gemco Keypad Assembly. Faceplate Membrane Switch on a 1995 A or L PLS not B with Brake Monitoring. Membrane Switch plate only (2LBS) 1/7 |
SD0382901 |
Ametek Gemco Keypad Assembly. Faceplate Membrane Switch on a 1995 B which has Brake Monitoring. Membrane Switch plate only (3LBS) 1/7 |
SD0392200 |
Ametek Gemco Spring, Main spring Assembly for a Linear Cable Reel. B and C Style Units |
SD0395100 |
Ametek Gemco Relay. Brake Monitor Input Relay for a 1995-B PLS. Solid State, 110 VAC Input |
SD0399000L125 |
Ametek Gemco Cable Assembly. Resolver Cable with Straight Connector for use with Series 1980R, 2110 or 2120 Series Systems with a single turn resolver input. 150 feet long. Add or subtract $ 2.00 per foot for other lengths |
SD0399000L15 |
Ametek Gemco Cable Assembly. Resolver Cable with Straight Connector for use with Series 2110 or 2120 Interface modules with a single turn resolver input by 15 feet long. Add $ 2.00 for each additional foot that might be required |
SD0399000L25 |
Ametek Gemco Cable Assembly. Resolver Cable with Straight Connector for use with Series 1980R, 2110 or 2120 Series Systems with a single turn resolver input. 25 feet long. Add or subtract $ 2.00 per foot for other lengths |
SD0399000L50 |
Ametek Gemco Cable Assembly. Resolver Cable with Straight Connector for use with Series 1980R, 2110 or 2120 Series Systems with a single turn resolver input. 50 feet long. Add or subtract $ 2.00 per foot for other lengths |
SD0399000L70 |
Ametek Gemco Cable Assembly. Resolver Cable with Straight Connector for use with Series 1980R, 2110 or 2120 Series Systems with a single turn resolver input. 70 feet long. Add or subtract $ 2.00 per foot for other lengths |
SD0399100L15 |
Ametek Gemco Cable Assembly with a Right angle Connector. Resolver to PLC Encoder Cable by 15 Feet Long. Add $ 2.00 for each additional foot that might be required |
SD0399900 |
Ametek Gemco Faceplate. Faceplate Assembly with Keypad for a 1996 Ram-Set Shut Height Controller |
SD0400000 |
Ametek Gemco Keylock & Wire Assembly for the 1996C Ram-Set Controller (1LB) |
SD0400800 |
Ametek Gemco Magnet. Standard Four Hole Magnet for Rod Style Probes. For use with probes 940, 950IS, 951, 952 & 952QD. 1.29 '' Diameter X 0.31 Thick with 4 Mounting Holes (<1LB) |
SD0401200L06 |
Ametek Gemco Cable Assembly for use with the 1995 PLS Output Expansion Module or the 1995 Remote Display. L06 = 6 Foot Long. Other lengths available, add $ 1.00 / Foot over 6 feet and change part number |
SD0401200L25 |
Ametek Gemco Cable Assembly. Controller to Remote Display. 25 Feet Long. Other lengths available, add $ 1.00 for each additional foot |
SD0401600L15 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver and a 1995 PLS Module. This cable is 15 Feet long with Straight Connectors. Add $ 2.00 per foot for cables over 15 feet long. |
SD0401600L30 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver and a 1995 PLS Module. This cable is 30 Feet long with Straight Connectors. Add $ 2.00 per foot for cables over 30 feet long (3LBS) |
SD0401600L50 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver and a 1995 PLS Module. This cable is 50 Feet long with Straight Connectors. Add $ 2.00 per foot for cables over 50 feet long |
SD0403800L25 |
Ametek Gemco Cable Assembly by 25 Feet Long |
SD0403900 |
Ametek Gemco Split Magnet Assembly for Rod Style Probes. Ametek Gemco Split Magnet Assembly for Rod Style Probes. For use with probes 940, 950IS, 951, 952 & 952QD |
SD0404600 |
Ametek Gemco Spring Tensioner Assembly for a 925B Linear Control Cable Reel. This tensioner reel has a 2.5 to 1 internal ratio |
SD0404601 |
Ametek Gemco Spring Tensioner Assembly for a 925B Linear Control Cable Reel. This cable tensioner has a 2 to 1 internal ratio |
SD0406100 |
Ametek Gemco Mounting Kit for a 1995 PLS. Shock mounting kit |
SD0407400L20 |
Ametek Gemco Cable & Connector for a 950 LDT by 20 Feet Long 1/8 |
SD0410300 |
Ametek Gemco Magnet. Cylinder Magnet. 1 Inch Diameter. Also available with Teflon Coated Surfaces |
SD0410600L314 |
Ametek Gemco Cable Assembly for a 925 Heavy-Duty Linear Cable Reel. 314 Inches Long |
SD0410900 |
Ametek Gemco Resolver. Series 1986. Standard Foot Mount 3/4 Inch Input Shaft. Standard Output, compatible with all Gemco electronic modules. 64 Turn Dual Resolver. (outputs 1 & 2 only) Standard Rear Mount Connector. Same as 1986A-1-D1-R-X |
SD0410901 |
Ametek Gemco Transducer Assembly, Dual Resolver with a 128 to 1 Ratio Gear Head |
SD0411100 |
Ametek Gemco Bracket. Rod Support Mounting Bracket for LDT's (1LB) |
SD0411200 |
Ametek Gemco Magnet. Large Split Steel Magnet Assembly for use with LDT'S. Use this Magnet with Rod Support Bracket SD0411100 2.5 Inch Diameter. 0.38 Inches Thick. 0.75 Inch Probe Hole (<1LB) |
SD0411201 |
Ametek Gemco Magnet. Large Split Stainless Steel Magnet for use with LDT'S. Use this Magnet with Rod Support Bracket SD0411100 2.5 Inch Diameter. 0.38 Inches Thick. 0.75 Inch Probe Hole (<1LB) |
SD0414600L192 |
Ametek Gemco Cable Assembly for a Linear Cable Reel. Insert length in total inches to complete the part number. Lengths over 120 inches add .31 / per inch |
SD0414600LXX |
Ametek Gemco Cable Assembly for a Linear Cable Reel. Insert length in total inches to complete the part number. Lengths over 120 inches add .31 / per inch |
SD0426600 |
Ametek Gemco Output Module for the 1992 Press-Set Press Controller. Relays for this module are ordered separately. 115 Volt AC in |
SD0426601 |
Ametek Gemco Output Module for the 1992 Press-Set Press Controller. Relays for this module are ordered separately. 230 Volt AC in |
SD0426700 |
Ametek Gemco Keyswitch Assembly for a 1992 Press-Set Controller |
SD0427100L15 |
Ametek Gemco Cable Assembly. Controller to output module, 15 Feet Long |
SD0430800L15 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver and a 1995 PLS Module. This cable is 15 Feet long with Right Angle Connectors. 15 = 15 Foot. Add $ 2.00 per Foot over 15 Feet |
SD0432600 |
Ametek Gemco Keypad & Faceplate Assembly for a 1992 Press-Set Controller (2LBS) |
SD0434300L15 |
Ametek Gemco Cable Assembly. Single Turn Resolver Cable for use with AMCI Resolver Input Modules. Color code matches AMCI & Modicon.Straight Connector,15 Foot Length Standard. Add $ 2.00 / foot for lengths over 15 Feet and change last 2 digits of the model number |
SD0434300L40 |
Ametek Gemco Cable Assembly. Single Turn Resolver Cable for use with AMCI Resolver Input Modules. Color code matches AMCI & Modicon.Straight Connector,40 Foot Length. Add $ 2.00 / foot for lengths over 40 Feet and change last 2 digits of the model number |
SD0434300L50 |
Ametek Gemco Cable Assembly. Single Turn Resolver Cable for use with AMCI Resolver Input Modules. Color code matches AMCI & Modicon.Straight Connector,50 Foot Length. Add $ 2.00 / foot for lengths over 50 Feet and change last 2 digits of the model number |
SD0436000L6 |
Ametek Gemco Cable Assembly for a 950A / 950TP Mill Duty LDT Housing with option for MS Style Connector by 6 Feet Long. Longer lengths are available, add $ 2.00 / for each additional Foot and change part number |
SD0436700L6 |
Ametek Gemco Cable Assembly for a 950 Mill Duty LDT Housing with option for MS Style Connector by 6 Feet Long. Longer lengths are available, add $ 2.00 / for each additional Foot and change part number |
SD0439600L25 |
Ametek Gemco Cable Termination Kit. Resolver Cable Termination Kit Includes Junction box which mounts on the crown of the press, Coiled Ram Cable which protects & controls cable connection to the resolver, 25 Feet long, other lengths available, add 2.00 / Ft over 25, tapping block, 2nd Cable Assembly 2110 to Junction Box |
SD0439700L06 |
Ametek Gemco Cable & Connector Assembly for a Rod Style Probes 950MD, 951, 952 & 952QD. 10 Pin Straight Connector. 6 Foot Length. Add $ 3.00 for each additional foot (2LBS) |
SD0439700L10 |
Ametek Gemco Cable & Connector Assembly for a Rod Style Probes 950MD, 951, 952 & 952QD. 10 Pin Straight Connector. 10 Foot Length. Add $ 3.00 for each additional foot (2LBS) |
SD0439700L100 |
Ametek Gemco Cable & Connector Assembly for a Rod Style Probe. 10 Pin Straight Connector. 100 Foot Length. Add $ 3.00 for each additional foot. Compatible with probes 950MD, 951, 952 & 952QD
|
SD0439700L12 |
Ametek Gemco Cable Connector for a Rod Style Probe. 10 Pin Straight Connector. 12 Foot Length Standard. Add $ 3.00 for each additional foot. Compatible with probes 950MD, 951, 952 & 952QD
|
SD0439700L15 |
Ametek Gemco Cable Connector for a Rod Style Probe. 10 Pin Straight Connector. 15 Foot Length Standard. Add $ 3.00 for each additional foot. Compatible with probes 950MD, 951, 952 & 952QD |
SD0439700L20 |
Ametek Gemco Cable Connector for a Rod Style Probe. 10 Pin Straight Connector. 20 Foot Length. Compatible with probes 950MD, 951, 952 & 952QD |
SD0439700L25 |
Ametek Gemco Cable Connector for a Rod Style Probe. 10 Pin Straight Connector. 25 Foot Length. Compatible with probes 950MD, 951, 952 & 952QD |
SD0439700L30 |
Ametek Gemco Cable Connector for a Rod Style Probe. 10 Pin Straight Connector. 30 Foot Length. Compatible with probes 950MD, 951, 952 & 952QD |
SD0439701L06 |
Ametek Gemco Cable Connector. 10 Pin Right Angle Connector, 6 Foot Standard. Compatible with probes 950MD, 951, 952 & 952QD. For longer lengths add $ 3.00 per foot |
SD0439701L50 |
Ametek Gemco Cable Connector. 10 Pin Right Angle Connector, 50 Foot Long. Compatible with probes 950MD, 951, 952 & 952QD. For longer lengths add $ 3.00 per foot |
SD0441300 |
Ametek Gemco Transducer Mounting Kit. Universal Transducer Mounting Bracket. Compatible with all Ametek Gemco LDT's. Simplifies mounting of linear displacement transducer between pitman arm & ram
|
SD0441300L25 |
Ametek Gemco Cable Termination Kit with 25 Foot J-Box to Controller / Monitor Cable for 951 and 952 Probes. Additional Cable over 25 Feet add $2.00 per Foot |
SD0443800L25 |
Ametek Gemco Cable Termination Kit for Press Applications. For 951 & 952 Digital LDT's. 25 Foot long. Add $ 2.00 for each additional Foot required |
SD0443803L25 |
Ametek Gemco Cable Termination Kit for Press Applications. For 951 & 952 Analog LDT's. 25 Foot long. Add $ 2.00 for each additional Foot required |
SD0445700 |
Ametek Gemco Cover. LDT Head Cover for Wet or Oily environments |
SD0465500L06 |
Ametek Gemco Cable Connector, High Temp Version 125 Degree C, for a Rod Style Probe. 10 Pin Straight Connector. 6 Foot Length Standard. Add $ 3.00 for each additional foot. Compatible with probes 950MD, 951, 952 & 952QD
|
SD0480900 |
Ametek Gemco Standard Four Hole Magnet for Rod Style Probes, Stainless Steel. For use with probes 940, 950IS, 951, 952 & 952QD |
SD0481500L125 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver and a 1771 PLS. Longer and shorter lengths available. The number after the ''L'' is the length. Cable lengths over 125 Foot add $ 2.00 / Foot |
SD0481500L15 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver and a 1771 PLS. Longer and shorter lengths available. The number after the ''L'' is the length. Cable lengths over 15 foot add $ 2.00 / Foot (1.6LBS) |
SD0481500L50 |
Ametek Gemco Cable Assembly for use with a Single Turn Resolver and a 1771 PLS. Longer and shorter lengths available. The number after the ''L'' is the length. Cable lengths over 50 foot add $ 2.00 / Foot |
SD0481600L15 |
Ametek Gemco Cable Assembly. Resolver Cable with a Right Angle Connector by 15 Feet Long. For other lengths add $ 2.00 per foot over 15 and change part number after the ''L'' |
SD0481600L150 |
Ametek Gemco Cable Assembly. Resolver Cable with a Right Angle Connector by 150 Feet Long. For other lengths add $ 2.00 per foot over 150 and change part number after the ''L'' |
SD0482700L25 |
Ametek Gemco Cable Termination Kit. Junction Box mounts on the press. Coiled Cable protects and controls cable connection to the Linear Transducer mounted on the Upper Arm. 25 Foot. 2110 / 1992 / 951VP |
SD0495600 |
Ametek Gemco Resolver. Internal Resolver used in 1980R Cam Box's. AMCI Style wired to a 7 Pin Connector |
SD0495800L6 |
Ametek Gemco Cable. PLS Module to I/O Module Rack |
SD0500900 |
Ametek Gemco 1999-SEM Meter Only |
SD0505000 |
Ametek Gemco Remote Tachometer Set. This set consists of: Tachometer Assembly, Magnetic Base, 2'' and 1'' Drive Wheel Assembly & Tachometer Drive Cone with Coupling |
SD0508200L130 |
Ametek Gemco Cable Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Straight Connector. L130 = 130 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 130 Feet and change part # |
SD0508200L15 |
Ametek Gemco Cable Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Straight Connector. L15 = 15 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 15 Feet and change part # |
SD0508200L150 |
Ametek Gemco Cable Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Straight Connector. L150 = 150 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 150 Feet and change part # |
SD0508200L250 |
Ametek Gemco Cable Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Straight Connector. L250 = 250 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 150 Feet and change part # |
SD0508200L30 |
Ametek Gemco Cable Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Straight Connector. L30 = 30 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 30 Feet and change part # (3LBS) |
SD0508200L300 |
Ametek Gemco Cable Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Straight Connector. L300 = 300 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 300 Feet and change part # |
SD0508200L45 |
Ametek Gemco Cable Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Straight Connector. L45 = 45 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 45 Feet and change part # (3LBS) |
SD0508200L60 |
Ametek Gemco Cable Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Straight Connector. L60 = 60 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 60 Feet and change part # |
SD0508300LXX |
Ametek Gemco Cable. Dual Resolver Connector & Cable Assembly. ( up to 15 Foot. Replace the XX in model mumber with feet required. Over 15 foot add $ 2.50 per foot over 15 |
SD0521800 |
Ametek Gemco Slide Magnet Assembly with a top mounted swivel linkage used with 955 Low-Profile LDT's |
SD0521801 |
Ametek Gemco Slide Magnet Assembly with a end mounted swivel for a 955 Low-Profile LDT |
SD0522000 |
Ametek Gemco LDT Mounting Foot. Order 2 per probe. Compatible with 956A, S & LC , 955D & QD (<1LB) |
SD0522100 |
Ametek Gemco Float Magnet for a 955 Low-Profile LDT |
SD0523800L6 |
Ametek Gemco Cable & Connector Assembly. Digital Output Board to PLC. 6 Foot Long. Add $ 2.50 for @ additional foot over 6 & change part number |
SD0528500L1 |
Ametek Gemco Cable Assembly for a 2500 Series Expansion Module by 1 Foot Long (<1LB) |
SD0528500L2.5 |
Ametek Gemco Expansion Module Cable. 2.5 Foot De-Pluggable (1LB) |
SD0528500L6 |
Ametek Gemco Expansion Module Cable. 6 Foot De-Pluggable (1LB) |
SD0531400L15 |
Ametek Gemco Cable & Connector Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Right Angle Connector L15 = 15 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 15 Feet and change part # (3LBS) |
SD0531400L30 |
Ametek Gemco Cable & Connector Assembly for a Single Turn Resolver and a 1746R Resolver Module or a 2500 PLS with a Right Angle Connector. L30 = 30 Feet Long. Shorter and longer lengths available. Add $2.00 for each additional foot required over 30 Feet and change part # 3 LBS Gross |
SD0545000 |
Ametek Gemco Communications Kit. Includes # 01533147 Communications Cable Assembly by 6 foot long & # 04545019 Converter RS232/RS485 with RJ11 Connector |
SD0545100 |
Ametek Gemco Mounting Feet with Spacers. Includes 2 Mounting Feet & Spacers to accommodate either a .45 or .75 Inch mounting height. Bottom of mounting foot to centerline of piston rod. Compatible with 955 D, DQ & LC & 956A, S & DQ LDT's (<1LB) |
SD0550500L40 |
Ametek Gemco Cable Assembly. Resolver Cable with a Right Angle Connector & Pigtail by 40 Feet Long. High Temp Cable Construction. Belden # 88777 rated to 200 degree C. For use with Series 1771 PLC Card. Resolver to rack module 4 (3LBS) |
SD0559800L6 |
Ametek Gemco Cable Assembly with a 10 Pin Female 6C Connector by 6 Feet Long |
SD2231 |
Ametek Gemco Cam Assembly. Special Cam @ 100 Degrees (<1LB) |
SD2382 |
Ametek Gemco Cam Assembly. Special Cam @ 45 Degrees (<1LB) |
SD2842C |
Ametek Gemco Resolver Single Turn Replaces SD2842C. Same as 1986A1XRX Series 1986 Industrial Duty Inline Resolver A = Standard Foot Mount with a 3/4 Inch Input Shaft 1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001 X = Single Turn Resolver, No gear reducer R = Standard Rear Mount Connector X = No options Enclosure NEMA 4 Max RPM 5000 Shaft Loading Axial 150 LBS Max Shaft Loading Radial 100 LBS Max (6LBS) |
SD3089B |
Ametek Gemco Resolver with connector |
Self Adjust |
Ametek Gemco Self Adjuster for lining wear on a Brake Assembly |
Stainless Steel Enclosure |
Ametek Gemco 304 Stainless Steel Enclosure, cover, latches, bearing flanges & flange bolts. 3/4 Inch 316 Stainless Input Shaft. Meets a NEMA 4X Rating 406 = $ 341.00 |
Strip Heater |
Ametek Gemco Strip Heater. Thermostatically Controlled, Adjustable, Strip Heater for a 1980 Series Cam Box. |
T8XXXX |
Ametek Gemco Thermistors. 9967 BASIC Thermistor. MOTOGARD Controllers are designed for use with Positive Temperature Coefficient Thermistors. Thermistor is encapsulated in a special epoxy for rugged mechanical duty, severe environments and good thermal conductivity# 22 - 26 Teflon Insulated Leads. Specify desired length of the leads. 6 Inch Minimum (<1LB) |
T9XXX |
Ametek Gemco Thermistors. 9967 BEARING PROBE Thermistor. MOTOGARD Controllers are designed for use with Positive Temperature Coefficient Thermistors. Thermistor is encapsulated in a special epoxy for rugged mechanical duty, severe environments and good thermal conductivity# 22 - 26 Teflon Insulated Leads. Specify desired length of the leads. 6 Inch Minimum (<1LB) |
TM-1035 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 10 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 200 Ft. Lbs. 1/2 Hour & 130 Ft Lbs. 1 Hour. With Shunt Coils 200 Ft. Lbs. 1 Hour & 150 Ft Lbs 8 Hours. Brake Weight 165 LBS. Net 190 LBS Shipping Weight. A 10 X 3.75 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost. A new self centering design is available at the same cost = TMSC |
TM-1035 Coil |
Ametek Gemco Brake Coil, 2 per brake, sold each, Shunt or Series Wound |
TM-1355 |
Ametek Gemco, aka Westinghouse, Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 13 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 550 Ft. Lbs. 1/2 Hour & 365 Ft Lbs. 1 Hour. With Shunt Coils 550 Ft. Lbs. 1 Hour & 400 Ft Lbs 8 Hours. Brake Weight 290 LBS. Net. A 13 X 5.75 Inch Brake Wheel is not included. This brake TMSC is also available to operated via a hydraulic slave cylinder for progressive brake application from a crane cab. Rectifier for AC Voltages are available at additional cost. A new self centering design is available at the same cost = TMSC (352LBS) |
TM-1355 Coil |
Ametek Gemco Brake Coil, 2 per brake, sold each, Shunt or Series Wound |
TM-1665 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 16 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 1000 Ft. Lbs. 1/2 Hour & 650 Ft Lbs. 1 Hour. With Shunt Coils 1000 Ft. Lbs. 1 Hour & 750 Ft Lbs 8 Hours. Brake Weight 490 LBS. Net 520 LBS Shipping Weight. A 16 X 6.75 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost. A new self centering design is available at the same cost = TMSC |
TM-1665 Coil |
Ametek Gemco Brake Coil, 2 per brake, sold each, Shunt or Series Wound |
TM-1985 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 19 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 2000 Ft. Lbs. 1/2 Hour & 1300 Ft Lbs. 1 Hour. With Shunt Coils 2000 Ft. Lbs. 1 Hour & 1500 Ft Lbs 8 Hours. Brake Weight 840 LBS. Net 870 LBS Shipping Weight. A 19 X 8.75 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost 1/8 |
TM-1985 Coil |
Ametek Gemco Brake Coil, 2 per brake, sold each, Shunt or Series Wound |
TM-2311 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 23 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 4000 Ft. Lbs. 1/2 Hour & 2600 Ft Lbs. 1 Hour. With Shunt Coils 4000 Ft. Lbs. 1 Hour & 3000 Ft Lbs 8 Hours. The TMSC Brake has interlocking shoe arms that allow for a single point adjustment for lining wear. Brake Weight 1200 LBS. Net 1260 LBS Shipping Weight. A 23 X 11.25 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost (1500LBS) 1/7 |
TM-3014 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 30 Inch Wheel Diameter, 9000 FT LB 1/2 Hour or 6750 FT LB 1 Hour, Voltage DC with Shunt or Series Wound Coils, Brake Weight 2450 LBS. A Brake Wheel is not included (2500LBS) 2/7 |
TM-43 |
Ametek Gemco (aka Westinghouse) Heavy Duty Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 4.5 Inch Wheel Diameter, with a Shunt or Series Wound Coil. With a Shunt Coil E004051, Designed for one or 8 Hour Duty.80 Volts Intermittent 64 Volts Continuous, 25 Ft LBS @ 1 Hour & 15 FT LBS @ 8 Hours. With a Series Wound, Brake coils are connected directly to in motor circuit. Series Coils are connected so that 1/2 of the current flows through each coil. Coil 25 FT LBS @ 1/2 Hour & 15 FT LBS @ 1 Hour. A 4.5 X 3.125 Inch Brake Wheel is not included. Available options include: Rectifiers for AC Voltages E010327 or E010326, Hand Release Levers, NEMA 3 and 4 Rated Enclosures (41LBS) |
TM-43 Coil |
Ametek Gemco Brake Coil, 1 per brake, Shunt or Series Wound |
TM-63 |
Ametek Gemco (aka Westinghouse) Heavy Duty Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 6 Inch Wheel Diameter, with a Shunt or Series Wound Coil. With a Shunt Coil 50 FT LBS @ 1 Hour & 40 FT LBS @ 8 Hours. With a Series Wound Coil 50 FT LBS @ 1/2 Hour & 40 FT LBS @ 1 Hour. A 6 X 3.125 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost (53LBS) |
TM-63 Coil |
Ametek Gemco Brake Coil, 1 per brake, Shunt or Series Wound |
TM-83 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 8 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 100 Ft. Lbs. 1/2 Hour & 65 Ft Lbs. 1 Hour. With Shunt Coils 100 Ft. Lbs. 1 Hour & 75 Ft Lbs 8 Hours. Weight 100 LBS. Net 137 LBS Shipping Weight. A 8 X 3.25 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost. A new self centering design is available at the same cost = TMSC |
TMSC-1035 |
Ametek Gemco Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 10 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 200 FT. LBS 1/2 Hour & 130 FT LBS. 1 Hour. With Shunt Coils 200 FT. LBS. 1 Hour & 150 FT LBS 8 Hours. The TMSC Brake has interlocking shoe arms that allow single point adjustment for lining wear. Brake Weight 165 LBS. Net 190 LBS Gross. A 10 X 3.75 Inch Brake Wheel is not included. This brake is also available to operate via a hydraulic slave cylinder for progressive brake application from a crane cab. A Rectifier for AC Voltages is an available option |
TMSC-1355 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 13 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 550 Ft. Lbs. 1/2 Hour & 365 Ft Lbs. 1 Hour. With Shunt Coils 550 Ft. Lbs. 1 Hour & 400 Ft Lbs 8 Hours. The TMSC Brake has interlocking shoe arms that allow single point adjustment for lining wear. Brake Weight 290 LBS. Net. A 13 X 5.75 Inch Brake Wheel is not included. This brake is also available to operate via a hydraulic slave cylinder for progressive brake application from a crane cab. Rectifier for AC Voltages are available at additional cost (352LBS) |
TMSC-1665 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 16 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 1000 Ft. Lbs. 1/2 Hour & 650 Ft Lbs. 1 Hour. With Shunt Coils 1000 Ft. Lbs. 1 Hour & 750 Ft Lbs 8 Hours. The TMSC Brake has interlocking shoe arms that allow for a single point adjustment for lining wear. Brake Weight 490 LBS. Net 520 LBS Shipping Weight. A 16 X 6.75 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost. |
TMSC-83 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 8 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 100 Ft. Lbs. 1/2 Hour & 65 Ft Lbs. 1 Hour. With Shunt Coils 100 Ft. Lbs. 1 Hour & 75 Ft Lbs 8 Hours. The TMSC Brake has interlocking shoe arms that allow for a single point adjustment for lining wear. Brake Weight 100 LBS. Net 137 LBS Shipping Weight. A 8 X 3.25 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost. |
TMSCH-1355 |
Ametek Gemco Electric / Hydraulic Brake 13 Inch Diameter DC Electric Brake Type TMSC with a Hydraulic Actuating Cylinder. Brake Assembly Only. This Brake is Spring Set and Electrically Released, when electrically released the Hydraulic Actuator becomes usable via a hydraulic brake system which is not included. Voltage DC with Shunt Coils 550 Ft LBS 1 Hour & 400 FT LBS 8 Hours. Brake Weight 290 LBS. plus skid. A Brake Wheel is not included. |
TMSCH-1355 System |
Ametek Gemco Electric / Hydraulic Brake System. One 13 Inch Diameter DC Electric Brake type TMSC with a Hydraulic Actuating Cylinder. This Brake is Spring Set and Electrically Released, when electrically released the Hydraulic Actuator becomes usable by the hydraulic foot pedal. System to include the Brake, Fluid Reservoir / Bleeder (AC, DC or Manually operated. Select 1), Bleeder Pushbutton Switch if there is an electrically operated FRB, Control Cylinder with Pedal, 4 Armored Hoses, Hydraulic Tubing by 100 Foot, Hydraulic Fittings, Gaskets, Brackets & Brake Fluid. Ametek Gemco Electric / Hydraulic Brake 13 Inch Diameter DC Electric Brake Type TMSC with a Hydraulic Actuating Cylinder. Brake assembly only. This Brake is Spring Set and Electrically Released, when electrically released the Hydraulic Actuator becomes usable via the hydraulic foot pedal. Voltage DC with Shunt Wound Coils. 550 Ft LBS 1 Hour & 400 FT LBS 8 Hours. Brake Weight 260 LBS. plus system components & shipping skid. A Brake Wheel is not included. |
TMSCH-1665 |
Ametek Gemco Electric / Hydraulic Brake 16 Inch Diameter DC Electric Brake Type TMSC with a Hydraulic Actuating Cylinder. Brake Assembly Only. This Brake is Spring Set and Electrically Released, when electrically released the Hydraulic Actuator becomes usable via a hydraulic brake system which is not included. Voltage DC with Shunt Coils 1000 Ft LBS 1 Hour & 750 FT LBS 8 Hours. Brake Weight 500 LBS. plus skid. A Brake Wheel is not included. |
TMSCH-83 |
Ametek Gemco (aka Westinghouse) Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 8 Inch Wheel Diameter, Voltage DC with Shunt or Series Wound Coils. With Series Coils 100 Ft. Lbs. 1/2 Hour & 65 Ft Lbs. 1 Hour. With Shunt Coils 100 Ft. Lbs. 1 Hour & 75 Ft Lbs 8 Hours. The TMSC Brake has interlocking shoe arms that allow for a single point adjustment for lining wear. Brake Weight 165 LBS. Net 190 LBS Shipping Weight. A 8 X 3.25 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost. |
UB-PS-8407-281EP |
Ametek Gemco Yates Seal. Piston Seal on a Ametek Gemco TMSCH-1355, BV 31/4X2 13/16 EPR |
1980-XXXX |
Ametek Gemco Engineered Product. Part number to be assigned at time of order. Similar to part number 1980-408-X-DP-TDI-R-1-L1 except with provisions to mount and couple a customer supplied encoder. The encoder is to be a Dynapar Series A5840960010 Options at additional cost and not included in the price include: Thermostatically controlled enclosure heater, add $ 222.00 304 stainless steel enclosure, cover, latches, internal camshaft, bearing flanges & flange bolts, add $ 475.00
|
1983 |
Ametek Gemco |
2000-XXXX |
Ametek Gemco Engineered part number to be established |
8130-12-2-A-S-R |
Ametek Gemco Electro-thrust disc brake assembly for 12'' diameter disc, 240 VAC 3PH, standard transformer oil, standard setting delay without valves, right hand orientation for actuator. |
917-65-CD-12-SP |
Ametek Gemco Obsolete 917 Cycle-Set 65 = Active Travel CD = 12 = Qty of Switches SP= Single Pole Double Throw Switches Only parts available are the Switches 1950-1-C-A-DO SPDT Switches 1950-1-C-A-DO DPDT Spring, Main Spring M0299700 |
D7010 |
Ametek Gemco Yates Tube. Replacement Tube, H4-F-N3.2X-1.00X1.38XXS13, Rev NS, TM1355 |