Back___________________Next__________________Home
Buy Your Industrial Control Products Here!
Gemco Part Description Page 2
| Part Number |
Product Category |
Description |
|---|---|---|
| 1025-B-1DP-S-X | Brake Parts | Ametek Gemco Foot Operated Switch B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 1DP = One D.P.D.T. Double Pole Double Throw Switch which can be wired for either Normally Open or Normally Closed Circuits S = Treadle Shield for Top & Side Protection |
| 1025-B-1SP-G-X | Brake Parts | Ametek Gemco Foot Operated Switches, Type "B" Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 1 SPDT ( 1 NO - 1NC ) with Treadle Guard to provide top protection from accidental operation |
| 1025-B-1SP-P-X | Brake Parts | Ametek Gemco Foot & Palm Switches. Series 1025 Type B Heavy Duty NEMA 4 Treadle Operated Foot Switch. 1 Contact Block 1 S.P.D.T. Switch that can be wired for a normally open or closed circuit. Only the enclosure is covered. The foot pedal is not covered (5LBS) |
| 1025-B-1SP-S-X | Brake Parts | Ametek Gemco Foot Operated Switches, Type "B" Heavy Duty Treadle Operated Foot Switch. NEMA 4, One contact block, 1 SPDT ( One 1 NO - 1NC ), S Cover Option = Treadle Shield provides Top & Side Protection C-H 10251-H35C with Switch Type B (8LBS) |
| 1025-B-1SP-U-X | Brake Parts | Ametek Gemco Foot Operated Switches, Type "B" Heavy Duty Treadle Operated Foot Switch. NEMA 4, One contact block, 1 SPDT ( One 1 NO - 1NC ), U Cover Option = Treadle Shield provides Top, Side and a Safety Gate which must be raised by the toe to gain access to the treadle (11LBS) |
| 1025-B-2DP-P-X | Brake Parts | Ametek Gemco Foot Operated Switch B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits X = No other options |
| 1025-B-2DP-S-L | Brake Parts | Ametek Gemco Foot Operated Switch. B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits S = Treadle Shield for Top & Side Protection L = Protective Shield |
| 1025-B-2DP-S-X | Brake Parts | Ametek Gemco Foot Operated Switch B = Heavy Duty NEMA 4 Treadle Operated Foot Switch 2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits S = Treadle Shield for Top & Side Protection |
| 1025-B-2SP-G-X | Brake Parts | Ametek Gemco Foot Operated Switches, Type "B" Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 2 SPDT ( Each 1 NO - 1NC ) with Treadle Guard to provide top protection from accidental operation |
| 1025-B-2SP-P-X | Brake Parts | Ametek Gemco Foot & Palm Switches. Series 1025 Type B Heavy Duty NEMA 4 Treadle Operated Foot Switch. 2 Contact Blocks, 2 S.P.D.T. Switches that can be wired for a normally open or closed circuits. Only the enclosure is covered. The foot pedal is not covered (5LBS) |
| 1025-B-2SP-S-X | Brake Parts | Ametek Gemco Foot Operated Switches, Type "B" Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 2 SPDT ( Each 1 NO - 1NC ) with Treadle Shield providing Top & Side Guard protection from accidental operation |
| 1025-C-2DP-S | Brake Parts | Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case, Cover & Treadle. Two Contact Blocks, 2 D.P.D.T. Switches (Each 2 NO - 2 NC) with Protective Shields. Six nameplates are provided, "START" "STOP" "FORWARD" "REVERSE" two are blank for special markings. Case has Qty. 2, 3/4" pipe tapped conduit entrances one of which is fitted with a pipe plug. (12LBS) |
| 1025-C-2DP-X | Brake Parts | Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case & Treadle. Two Contact Blocks, 2 D.P.D.T. Switches (Each 2 NO - 2 NC) Six nameplates are provided, "START" "STOP" "FORWARD" "REVERSE" two are blank for special markings. Case has Qty. 2, 3/4" pipe tapped conduit entrances one of which is fitted with a pipe plug. (11LBS) |
| 1025-C-2SP-S | Brake Parts | Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case, Cover & Treadle. Two Contact Blocks, 2 S.P.D.T. Switches (Each 1 NO - 1 NC) with Protective Shields. Six nameplates are provided, "START" "STOP" "FORWARD" "REVERSE" two are blank for special markings. Case has Qty. 2, 3/4" pipe tapped conduit entrances one of which is fitted with a pipe plug (11LBS) |
| 1025-C-2SP-X | Brake Parts | Ametek Gemco Switch. Foot Operated Switches, Type "C" Heavy Duty Side Treadle Operated Foot Switch. NEMA 4 Enclosure, Two Contact Blocks, Two Snap action Single Pole Double Throw Switches that can be wired for either Normally Open or Normally Closed Circuits. Six Name Plates are provided. START STOP FORWARD REVERSE & Two are blank for your custom marking (7LBS) |
| 1025-D-1SP | Brake Parts | Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. One S.P.D.T. Switch (1 NO - 1 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS) |
| 1025-D-2DP | Brake Parts | Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. Two D.P.D.T. Switch (2 NO - 2 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS) |
| 1025-D-2SP | Brake Parts | Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. One D.P.D.T. Switch (2 NO - 2 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS) |
| 10316H-169-1 | Brake Parts | Ametek Gemco 2006-402-L-1080-A |
| 10316H89A | Brake Parts | Ametek Gemco 1950-1-B-A-DO C-H Part # shown above |
| 104A020XXXX | Brake Parts | Ametek Gemco Thermistors. 9967 LUG Thermistor. MOTOGARD Controllers are designed for use with Positive Temperature Coefficient Thermistors. Thermistor is encapsulated in a special epoxy for rugged mechanical duty, severe environments and good thermal conductivity# 22 - 26 Teflon Insulated Leads. Specify desired length of the leads (<1LB) |
| 104A022XXXX | Brake Parts | Ametek Gemco Thermistors. 9967 SPRING LOADED PROBE Thermistor. MOTOGARD Controllers are designed for use with Positive Temperature Coefficient Thermistors. Thermistor is encapsulated in a special epoxy for rugged mechanical duty, severe environments and good thermal conductivity# 22 - 26 Teflon Insulated Leads. 7/16 Inch Diameter. 1/4 Inch NPT. Specify desired probe length, 2 to 6 Inches is standard. Specify lead length (<1LB) |
| 107085 | Brake Parts | Ametek Gemco Repair Kit, for a Moisture Ejection Valve. ISG SAP 1170357 |
| 107163002 | Brake Parts | Ametek Gemco Pressure Cluster Assembly, 1 X 8, with special piston for long static lines, like 54086 |
| 1090-A1 | Brake Parts | Ametek Gemco Obsolete 12 Bit unit. Replaced by 1090B1 a 14 Bit unit |
| 1090B1 | Brake Parts | Ametek Gemco Multibus High Speed Programmable Limit Switch. 14 Bit Resolution. Replaced 1090A1 |
| 115101-2 | Brake Parts | Ametek Gemco MOTOGARD 9966. Series 115 Over Temperature Protection System. 6 Inputs, 2 Triac Outputs 1-N.O. 1 N.C. Input Rating: 120 VAC + or - 10% Single Phase 50/60 Hz. Output Rating: 120 /240 Volts 5 amp continuous. Reset is automatic. Enclosure 5.5" Wide X 4.25" Long X 3.12" High Potted in a NEMA 4 Steel Case (2LBS) |
| 120101 | Brake Parts | Ametek Gemco MOTOGARD 9966. Series 120 Over Temperature Protection System |
| 135101 | Brake Parts | Ametek Gemco MOTOGARD 9966. Series 135 Over Temperature Protection System |
| 14" H 2 | Brake Parts | Ametek Gemco 14 Inch Hydraulic Brake System, Qty. 2, Brake Assemblies each capable of 0 to 600 LBS / FT Torque, Control Cylinder, Pedal, Fluid Reservoir Bleeder, 250 Foot of Tubing, 6 Armored Hoses, 3 Gallons of 21B Wagner Brake Fluid and Fittings, 6 Brackets, 6 Jam Nuts, 36 Tube Nuts, 6 Lock Washers, 15 Copper Gaskets, 85 Bushings, 85 Clamps, 7 Unions for a complete system, less brake wheels. |
| 14" HM 1 | Brake Parts | Ametek Gemco 14 X 6.50 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 600 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 550 FT LBS. Includes one 14 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 289 LBS Net. |
| 14"-H-1 | Brake Parts | Ametek Gemco 14 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 600 LBS. / FT dynamic stopping torque. Includes Qty.1, 14 Inch Hydraulic Brake Assembly, DC Fluid Reservoir Bleeder, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 14 Inch Brake Weight 161 LBS. Overall Width 25 - 7/8 Inch, Height 28 - 1/2 Inch. A 7905 Brake Actuator is provided / used on a single brake system (320LBS) |
| 1500-H-L3-S9-N1-X | Brake Parts | Ametek BW Controls Induction Control Relay model 1500-H-L3-S9-N1-X, 440 VAC Line Voltage, 480VAC Secondary Voltage, Nema 1 Enclosure without any other options. |
| 1500-HL1-S30-C-X | Brake Parts | Ametek BW Controls Relay. Series 1500 Induction Control Relay. 110 volts Primary, 40 Volts Secondary |
| 1500F-L1-S7OCX | Brake Parts | Ametek BW Controls Induction Control Relay |
| 150101 | Brake Parts | Ametek Gemco MOTOGARD 9966. Series 150 Over Temperature Protection Systems provide immediate overheating protection for motors equipment enclosures, semiconductor heatsinks, sleeve bearings and other related machinery. For use with PTC Thermistors embedded in or in contact with the monitored surface. 1 Input, Form C Relay Output. 2 Triac Outputs 1-N.O. 1 N.C. Input Rating: 120 VAC + or - 10% Single Phase 50/60 Hz. Output Rating: 120 VAC for size 5 contactor coil. Reset is automatic. Enclosure 3.25" Wide X 2.25" Long X 2.50" High. Potted in a polyester case. Conforms with NEC Requirements for integral motor thermal protection (1LB) |
| 16-204 | Brake Parts | Ametek Gemco Switch see AME-04537004 |
| 1746L-1 | Brake Parts | Ametek Gemco LDT Interface Card. Single Axis, One LDT Input. Specify LDT output if other than: CP, VPI or RS (2LBS) |
| 1746L-2 | Brake Parts | Ametek Gemco LDT Interface Card. Two Axis, Two LDT Inputs. Specify LDT output if other than: CP, VPI or RS (2LBS) |
| 1746R-1 | Brake Parts | Ametek Gemco Interface Card. Series 1746R Resolver Interface Card incorporates Allen-Bradley licensed technology for complete compatibility with A-B Series 1746 I/O Chassis. The unit monitors machine position from a resolver and delivers continues absolute position data at 12 bit (4,096 count) resolution and RPM data to the SLC processor. |
| 1746R-2 | Brake Parts | Ametek Gemco Interface Card. Series 1746R Resolver Interface Card incorporates Allen-Bradley licensed technology for complete compatibility with A-B Series 1746 I/O Chassis. The unit monitors machine position from a resolver and delivers continues absolute position data at 12 bit (4,096 count) resolution and RPM data to the SLC processor. Two axis resolver interface. Two resolver inputs or field configurable for one multi-turn dual resolver. |
| 17618 | Brake Parts | Ametek Gemco Washer on Spring Case Gasket Kit |
| 1771-PLS-B1 | Brake Parts | Ametek Gemco Ultra-High Speed Programmable Limit Switch (PLS) with 16 direct outputs from the front panel that update every 5 microseconds. A resolver based unit that incorporated Allen-Bradley technology and is completely compatible with the A-B Series 1771 I/O chassis. Internally powered by the PLC backplane. Resolver input with 14 bit (16,384 count) resolution and field programmable scale factor. Reset to Preset Inputs & Speed Compensation. This product incorporates patented technology which is licensed by Allen -Bradley Company Inc. Allen-Bradley is a registered trademark of Rockwell Corporation (3LBS) |
| 1771-PLS-C1 | Brake Parts | Ametek Gemco Programmable Limit Switch. Allen Bradley Series 1771 Compatible High Speed Programmable Limit Switch. Standard 14 Bit Resolution (4LBS) |
| 18" H-2 | Brake Parts | Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 1800 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 18 Inch Hydraulic Brake Assemblies J002932, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. Brake Wheels are not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (670LBS) |
| 18" HM 1 | Brake Parts | Ametek Gemco 18 X 8.50 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 900 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 700 FT LBS. Includes one 18 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 389 LBS Net. |
| 18"-H-1 | Brake Parts | Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 900 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty.1, 18 Inch Hydraulic Brake Assembly J002932, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 100 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.4, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. A Brake Wheel is not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (359LBS) |
| 1950-1-B-A-AO | Brake Parts | Ametek Gemco Switch 1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco 1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit B = Binder / Screw Terminals 4 A = Front Mounting AO = Switch Plunger operated via cam or roller follower U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC -50 to 185 Degree F Recommended replacement @ 15 million cycles (<1LB) |
| 1950-1-B-A-AR | Brake Parts | Ametek Gemco Switch 1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco 1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit B = Binder / Screw Terminals 4 A = Front Mounting A = Switch Plunger operated via cam or roller follower R = Rubber boot for addition protection form humidity and dust U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC -50 to 185 Degree F Recommended replacement @ 15 million cycles (<1LB) |
| 1950-1-B-A-BO | Brake Parts | Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Front Mounting, Lever & 1/2" Dia. Roller Assembly |
| 1950-1-B-A-DO | Brake Parts | Ametek Gemco Switch. Precision Snap Action Switch Assembly. SPDT Single Pole Double Throw, Qty. 4 Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit, Front Mounting, Plunger Push Operator, 2006 Type K, U.L. Listed (<1LB) |
| 1950-1-B-A-DR | Brake Parts | Ametek Gemco Switch. Precision Snap Action Switch Assembly. 1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit, B = Binder Terminals, A = Front Mounting, DR = Plunger with Boot, Push Operated, U.L. Listed (<1LB) |
| 1950-1-C-A-BO | Brake Parts | Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, 915 / 917 Cycl-Set Terminals, Front Mount, Lever & 1/2 Inch Diameter Roller Assembly. |
| 1950-1-C-A-DO | Brake Parts | Ametek Gemco Switch. Precision Snap Action Limit Switch Assembly, Single Pole Double Throw / S.P.D.T., 4 screw terminals, can be wired for either Normally Open or Normally Closed Circuits. Front Mount, Plunger Push Operator. 915 / 917 Cycl-Set & 2006 K RS (<1LB) |
| 1950-1-D-A-AO | Brake Parts | Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Saddle Clamp Terminals, Front Mounting, Plunger Cam Operated |
| 1950-1-D-A-DO | Brake Parts | Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Saddle Clamp Terminals, Front Mounting, Plunger Push Operator ( Cycl-Set & 2006K RS ) |
| 1950-1-P-A-AO | Brake Parts | Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Plug-In Terminals, Front Mounting, Plunger Cam Operated |
| 1950-1-P-A-AR | Brake Parts | Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Plug-In Terminals, Front Mounting, Plunger Cam Operated, Plunger with boot-cam operator. |
| 1950-1404 | Brake Parts | Ametek Gemco Switch. Precision Snap Limit Switch Unit. Single Pole Double Throw (S.P.D.T.) Plunger OP Bind TE with Boot and Heavy Springs. For use with the Series 1970 Driv Cheks (<1LB) |
| 1950-1405 | Brake Parts | Ametek Gemco Switch. Precision Snap Limit Switch Unit. Double Pole Double Throw, Plunger Operated. Binder Terminals with Heavy Springs. 1970 Drive Chek (<1LB) |
| 1950-1406 | Brake Parts | Ametek Gemco Switch. Obsoleted in 2006, See 1950-1413. Precision SPST Slow Make - Slow Break Switch Assembly. N.C. Normally Closed. Special Purpose Switch. U.L. Listed For the 1980 Product Line (<1LB) |
| 1950-1408 | Brake Parts | Ametek Gemco Switch. SPDT Slow Make Slow Break. For products 915 / 917/ 2006 (<1LB) |
| 1950-1413 | Brake Parts | Ametek Gemco Switch. Precision Slow Make - Slow Break Single Pole Double Throw Switch Assembly. Can be wire for either a normally open or normally close circuit. 4 screw terminals on this switch. Replaces 1950-1406 which is obsolete (<1LB) |
| 1950-1414 | Brake Parts | Ametek Gemco Switch. Single Pole Double Throw with a Heavy Duty Spring for high vibration applications. Can be wired for normally open or closed circuits, 4 screw terminals. Replaces obsolete 1950-1416 but is not a Slow Make Slow Break Switch (<1LB) |
Fenton, MO 63026
Phone: (636) 537-0202
E:mail: [email protected]