Back___________________Next__________________Home<
Buy Your Industrial Control Products Here!
Gemco Parts Description Page 21
| Part Number |
Product Category |
Description |
|---|---|---|
| CB-110 | Brake Parts | Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / solenoid Released, 7 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 85 Ft LB Continues or 110 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel. 60 LBS. Gross Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear. |
| CB-15 | Brake Parts | Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 4.5 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 10 Ft LB Continues or 15 FT LB Intermittent, less a 4.50 X 2.75 Inch Brake Wheel E004800. (20LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear. |
| CB-160 | Brake Parts | Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 10 Inch Diameter, Many AC Voltages, 60 or 50 Hz., Single Phase., 160 FT LB Intermittent Duty, 125 FT LB continues Duty, less a 10.00 X 4.25 Inch Brake Wheel E010800. 78 LBS Net. Motor Freight on a skid. Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear |
| CB-35 | Brake Parts | Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 25 Ft LB Continues or 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel E005500. (34LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear |
| CB-75 | Brake Parts | Ametek Gemco Brake Assembly, AC Solenoid, Spring Set / Solenoid Released, 7 Inch Diameter, AC Voltages, 60 & 50 Hz., Single Phase, 50 FT LB Continues or 75 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel E007500. (60LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear |
| CO197500 | Brake Parts | Ametek Gemco Cover. Cover only for a Series 1980 NEMA , 4 to 6 Circuit Cam Box (4LBS) |
| Cast Iron or Bronze Encl | Brake Parts | Ametek Gemco Cast Bronze Enclosure for NEMA 4 2000 Series Worm Gear Limit Switches, adder |
| Coil TM- 63 | Brake Parts | Ametek Gemco Coil for a TM-63 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 1 per brake. |
| Coil TM- 83 | Brake Parts | Ametek Gemco Coil for a TM-83 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each (25LBS) |
| Coil TM-1035 | Brake Parts | Ametek Gemco Coil for a TM-1035 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each (30LBS) |
| Coil TM-1355 | Brake Parts | Ametek Gemco Coil for a TM-1355 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each |
| Coil TM-1665 | Brake Parts | Ametek Gemco Coil for a TM-1665 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each |
| Coil TM-1985 | Brake Parts | Ametek Gemco Coil for a TM-1985 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each 1/8 |
| Coil TM-2311 | Brake Parts | Ametek Gemco Coil for a TM-2311 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each 3/7 |
| Coil TM-3014 | Brake Parts | Ametek Gemco Coil for a TM-3014 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each |
| Coil TM-43 | Brake Parts | Ametek Gemco Coil for a TM-43 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 1 per brake. |
| Conversion System Type H | Brake Parts | Ametek Gemco A/H-ERC Conversion System for Type H Wagner Hydraulic Brake Systems. Converts a Wagner manual brake system to an Air Over Hydraulic Brake System that can be controlled remotely via an electric circuit. This conversion is for Wagner Hydraulic Brake Systems though other hydraulic brake systems could be suitable for this conversion. (system suitability investigation would be required) The Conversion System Includes: One 3/4 HP Motor Driven Compressor Assembly, One Pre- Piped and Pre-Wired Control Panel, One Two-Way Hydraulic Check Valve, One Installation Kit including all the necessary tubing, fittings & fluid. If the existing brake system does not include a Fluid Reservoir Bleeder, it is required, and is at additional cost. This system requires electrical input of 230 Volt DC or 460 Volt AC, 3 Phase, 60 Hz for the compressor and 115 Volt Control on AC Systems. Please specify AC or DC at time of order. Systems are available with the HM parking option at additional cost. |
| D7010 | Brake Parts | Ametek Gemco Yates Tube. Replacement Tube, H4-F-N3.2X-1.00X1.38XXS13, Rev NS, TM1355 |
| DT-2RV212-A7 | Brake Parts | Ametek Gemco Switch 04537003 |
| E004022 | Brake Parts | Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 4.5 Inch Diameter, 460 Volt AC, 60 Hz., Single Phase., 15 FT LB Intermittent, less a 4.50 X 2.75 Inch Brake Wheel E004800. (20LBS) |
| E004044 | Brake Parts | Ametek Gemco Resistor for a TM43 Brake Assembly with a shunt wound coil. This is the standard resistor. Not to be used with rectifiers employing a Forcing Scheme. E004045 is used with a Forcing Scheme Rectifier |
| E004045 | Brake Parts | Ametek Gemco Resistor. Forcing Resistor for use with a TM-43 Brake Assembly |
| E004047 | Brake Parts | Ametek Gemco Brake Shoe & Lining for a TM-43 4.5 Inch Electric Brake, Bonded Non-Asbestos Lining Material. Sold each, 2 per Brake. 70 Degree Arc, 645C555G02 (2LBS) |
| E004051 | Brake Parts | Ametek Gemco Coil. Shunt Wound Coil for a TM-43 Brake Assembly. Intermittent Duty, 1 Hour Cycle 80 Volts DC / 1.10 AMPS. Continuous Duty, 8 Hour Cycle 64 Volts DC / 0.88 AMPS. Average Cold Coil Resistance 73 OHMS. Ref # 26 1 coil per brake 645C545G16 Resistors are required in series E004044 / Forcing E004045 (16LBS) |
| E004054 | Brake Parts | Ametek Gemco Pin on a CB35 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H01 (<1LB) |
| E004055 | Brake Parts | Ametek Gemco Pin on a CB-15 Brake Assembly. Between Link and Lever. Ref. # 8 1 per brake. 2247C08H02 (<1LB) |
| E004056 | Brake Parts | Ametek Gemco Pin on a CB15 Brake Assembly. Connects plunger & link. Item Ref. 6. 1 per brake 2247C08H03 (<1LB) |
| E004059 | Brake Parts | Ametek Gemco Lever for a CB15 4 & 1/2 Inch Brake Assembly. Lever between plunger link and inner shoe arm. 2247C09H01 |
| E004060 | Brake Parts | Ametek Gemco Rod. Adjusting Rod on a CB15 4 & 1/2 Inch Brake, 1 per brake. Ref # 17 , 3279B86G01 |
| E004062 | Brake Parts | Ametek Gemco Link on a CB-15 brake Assembly. Between plunger & lever arm. Item Ref. 7. 1 per brake. 3279B92H01 (1LB) |
| E004063 | Brake Parts | Ametek Gemco Spring Seat on a CB15 Brake Assembly. Ref # 10 1 per brake. Old Westinghouse # 3279B94Ho2 |
| E004065 | Brake Parts | Ametek Gemco Spring, Main Tension on a CB15 Brake Assembly. Ref # 11 1 per brake. Old Westinghouse # 3280B02H01 |
| E004070 | Brake Parts | Ametek Gemco Bolt. Brake Shoe Bolt for a TM43 or TM63 Brake, 27D7221H04 1/2 - 13 X 3-1/4" LG STL G2 PLATED HEX HD CAP Ref # 15, 2 per brake (1LB) |
| E004071 | Brake Parts | Ametek Gemco Seat/ Plate. Spring Seat / Plate on the Wheel End of a TM43 Brake, Ref. # 9, 318B777H01 (1LB) |
| E004074 | Brake Parts | Ametek Gemco Block. Inner Hinge Block on a TM-43 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H01 |
| E004075 | Brake Parts | Ametek Gemco Release Bushing on a TM43 Brake |
| E004076 | Brake Parts | Ametek Gemco Main Spring Seat on a TM43 Brake Assembly |
| E004077 | Brake Parts | Ametek Gemco Dust Seal for the Coil on a TM43 Brake Assembly |
| E004078 | Brake Parts | Ametek Gemco Spring. Wheel End Spring on a TM-43 Brake Tie Rod Ref. # 11 1 per brake. Recommended spare part 438A070H15 (1LB) |
| E004079 | Brake Parts | Ametek Gemco Tension Spring on a TM43 Brake Assembly |
| E004080 | Brake Parts | Ametek Gemco Tension Spring on a TM43 Brake Assembly |
| E004097 | Brake Parts | Ametek Gemco Tie Rod on a TM43 4 Inch Brake Assembly. Ref #7. 1 per brake. Old Westinghouse 635C104G09 |
| E004098 | Brake Parts | Ametek Gemco Bushing for a TM43 or TM63 Brake Assembly, 2 per brake |
| E004101 | Brake Parts | Ametek Gemco Lining and Rivet Kit on a CB15 Brake Assembly. Linings have 4 countersunk holes for the rivets. Also available undrilled for bonded applications. Old Westinghouse # 3279B95G01 1 kit per brake. recommended spare part (1LB) |
| E004102 | Brake Parts | Ametek Gemco Coil for a CB-15 Brake. 460 Volt 60 Hz. Single Phase, 3280B04G03 (1LB) |
| E004104 | Brake Parts | Ametek Gemco Coil for a CB-15 Brake. 115 Volt 60 Hz. Single Phase, 3280B04G01 (1LB) |
| E004105 | Brake Parts | Ametek Gemco Coil for a CB-15 Brake. 230 Volt 60 Hz. Single Phase, 3280B04G02 (1LB) |
| E004107 | Brake Parts | Ametek Gemco Coil for a CB-15 Brake. 200 Volt 60 Hz. Single Phase, 3280B04G17 (1LB) |
| E004109 | Brake Parts | Ametek Gemco Solenoid Assembly on a 4.5" Dia. CB15 Brake Assembly, includes Plunger & Solenoid Guides, 3279B97H01 |
| E004113 | Brake Parts | Ametek Gemco Shoe with Lining, Inner, for a CB15 Brake, old 2254C28G01 |
| E004114 | Brake Parts | Ametek Gemco Shoe with Lining, Outer, for a CB15 Brake, old 2254C27G01 |
| E004117 | Brake Parts | Ametek Gemco Lining & Rivet Kit for a TM43 4.5 Inch Dia. Electric Brake, 1 Pair drilled for with rivets. The rivets are included. Old Westinghouse # 961C691G23. Undrilled linings for bonded application are also available. Just specify undrilled on any order. |
| E004118 | Brake Parts | Ametek Gemco Arm. Outer Brake Shoe Arm on a TM-43 Brake. Ref # 16, 1 per brake, 645C544G01 |
| E004143 | Brake Parts | Ametek Gemco Block. Wheel End Hinge Block for a TM43 Brake. Ref # 12 1 per brake. 318B787H01 |
| E004153 | Brake Parts | Ametek Gemco Coil for a TM43 Brake. Series Wound Coil. 32 Amps 1/2 Hour & 26.5 Amps 1 Hour. Resistance 0.181 OHMS. |
| E004154 | Brake Parts | Ametek Gemco Coil. Series Coil for a TM-43 Brake Assembly. 26.5 AMPS Intermittent Duty Cycle, 0.287 Ohms Resistance, G645C545G26 (8 LBS) |
| E004167 | Brake Parts | Ametek Gemco Coil. Series Coil for a TM-43 Brake Assembly. 12.5 Amps .5 Hour & 10.3 Amps 1 Hour. Resistance 1.18 Ohms, average.. Ref # 26 1 Coil is required on this brake. Old Westinghouse # 645C545G23 |
| E004175 | Brake Parts | Ametek Gemco Bushing. Neoprene Bushing on a CB-15 or CB-35 Brake. 2 per brake (<1LB) |
| E004182 | Brake Parts | Ametek Gemco Series Coil for a TM-43 Brake Assembly. .Item # 26. 936 Ohms Res. 14 AMPS / 1/2 Hour . 11.5 AMPS / 1 Hour. Old Westinghouse # 208C757G16 1 per brake. |
| E004500 | Brake Parts | Ametek Gemco Brake Wheel for the TM-43 Brake Assembly, 4.5 Inch Diameter, 3.125" Face, 1.56 Offset, 2.62" Hub Length, 2.75 Inch Hub Diameter, 1.625" Maximum Bore, 9850 Maximum, RPM, Offset Hub Style ( symmetrical hub style also available), Solid Hub with centerline machined. WK2 / LB FT2 .14 Add $ 125.00 to finish hub offset, hub length, bore & key. |
| E004600999-C- | Brake Parts | Ametek Gemco Brake Wheel 4.5 |
| E004800 | Brake Parts | Ametek Gemco Brake Wheel for the CB15 Brake Assembly, 4.5 Inch Diameter, 2.75" Face, 2.64" Offset, 2.2" Hub Length, Solid Hub with center line machined. 1.625" Maximum Bore, 9850 Maximum RPM, 2247C13H01 Add $125.00 to finish hub, bore & keyway (9LBS) |
| E005001 | Brake Parts | Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 230 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS) |
| E005002 | Brake Parts | Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 460 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS) |
Fenton, MO 63026
Phone: (636) 537-0202
E:mail: [email protected]