Back___________________Next__________________Home
Buy Your Industrial Control Products Here!
Gemco Parts Description Page 28
| Part Number |
Product Category |
Description |
|---|---|---|
| ETH-13 Brake Only DC | Brake Parts | Ametek Gemco spring applied, electro-hydraulically released, 13 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 230 Volt DC Shunt Wound Motor.550 FT LBS. |
| ETH-13 Brake Sys | Brake Parts | Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 250 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters. System includes: Qty. 1, ET-13H Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703 |
| ETH-13 Brake Sys DC | Brake Parts | Ametek Gemco Electro-Thrust Brake System with Hydraulic Cab Control. 13 Inch Diameter Brake, 550 LB FT, 230 VDC Shunt Wound Motor. Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, hydraulic actuator for auxiliary cab control for a progressive hydraulic brake pedal actuation. System includes: Qty. 1, ET-13 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703 |
| ETH-14NA | Brake Parts | Ametek Gemco spring applied, electro-hydraulically released brake assembly with hydraulic actuator for auxiliary manual cab control via foot pedal (sold separately). The thruster includes a 230VDC motor. The brake is set up for a 14" diameter wheel which is not included. Two 10797 armored hose kits are included. A fluid reservoir bleeder is required, but not included. A manual hydraulic foot pedal control cylinder is required, but not included. |
| ETH-14NA BO | Brake Parts | Ametek Gemco spring applied, electro-hydraulically released, 14 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 460 / 230 Volt AC motor. 800 FT LBS. |
| ETH-16 Brake Only | Brake Parts | Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 400 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters |
| ETH-16 Brake Only DC | Brake Parts | Ametek Gemco spring applied, electro-hydraulically released brake assembly with hydraulic actuator for auxiliary manual cab control via foot pedal (sold separately). 1000 LB / FT. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake.The thruster includes a 230VDC motor. The brake is set up for a 16" diameter wheel which is not included. A fluid reservoir bleeder is required, but not included. A manual hydraulic foot pedal control cylinder is required, but not included. |
| ETH-16 Brake Sys DC | Brake Parts | Ametek Gemco spring applied, electro-hydraulically released brake system with hydraulic actuator for auxiliary manual cab control via foot pedal. 1000 LB / FT. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake. The thruster includes a 230VDC Shunt Wound Motor. The brake is set up for a 16" diameter wheel which is not included. System includes: Qty. 1, ETH-16 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703 |
| ETH-16 Brake System AC | Brake Parts | Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a foot pedal. 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. System includes: Qty. 1, ETH-16 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703400 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters |
| Enclosure CB110 NEMA 4 | Brake Parts | Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
| Enclosure CB15 NEMA 4 | Brake Parts | Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
| Enclosure CB160 NEMA 4 | Brake Parts | Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
| Enclosure CB35 NEMA 4 | Brake Parts | Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
| Enclosure CB75 NEMA 3 | Brake Parts | Ametek Gemco Electric Brake Enclosure. NEMA 3. Approval Drawing required. Must be ordered with brake |
| Enclosure CB75 NEMA 4 | Brake Parts | Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake. |
| Enclosure ET-8 | Brake Parts | Ametek Gemco Enclosure. NEMA 3R Enclosure for a ET-8 Brake Assembly. Specifically 8210-8-4-A-S-X-X-N-I |
| Enclosure NEMA 12 | Brake Parts | Ametek Gemco Enclosure. NEMA 12 Enclosure for all AHM Panels. 36 X 48 Inches |
| Enclosure TM-1665 NEMA 4 | Brake Parts | Ametek Gemco Enclosure. NEMA 4 Rated Enclosure for a TM-1665 Brake assembly. Includes Brake Wheel Shaft Seals. Shaft Diameters and approval drawing are required. Enclosures must be ordered with a brake. A Thermostatically Controlled Heater is available at additional cost |
| Enclosure TM83 | Brake Parts | Ametek Gemco Enclosure. NEMA 3R Enclosure for a TM83 Brake Assembly |
| Enclosure TMSC-1035 | Brake Parts | Ametek Gemco Enclosure. NEMA 3R Enclosure for a TMSC-1035 Brake Assembly |
| Enclosure TMSC-1355 | Brake Parts | Ametek Gemco Enclosure. NEMA 3R Enclosure for a TMSC-1355 Brake Assembly. Approval drawing provided, requires signature |
| Enclosure TMSC-1665 | Brake Parts | Ametek Gemco Enclosure. NEMA 4 Enclosure for a TMSC-1665 Brake Assembly. Approval drawing provided, requires signature |
| F00017 | Brake Parts | Ametek Gemco Gasket. Copper Gasket , used with armored hose, 33/64" I.D. (<1LB) |
| F000602 | Brake Parts | Ametek Gemco Gasket. Copper Gasket (<1LB) |
| F000603 | Brake Parts | Ametek Gemco Gasket. Copper Gasket (<1LB) |
| F000996 | Brake Parts | Ametek Gemco Plug |
| F002395 | Brake Parts | Ametek Gemco Boot. Actuator Boot, Item 11, used on actuating cylinders J007905, J023437 & J008765 (1LB) |
| F004481 | Brake Parts | Ametek Gemco Adapter 1 X 16 for a Disc Brake Power Cluster (-1LB) |
| F006446 | Brake Parts | Ametek Gemco Screw. Bleeder Screw (<1LB) |
| F011955 | Brake Parts | Ametek Gemco Adaptor Fitting, 1/2 -20 UNF Male to 1/4-18 NPTF Male, Brass (1LB) |
| F020412 | Brake Parts | Ametek Gemco 2 Way Hydraulic Check Valve with Fittings for 1/4 Inch O.D. Copper Tubing |
| F034635 | Brake Parts | Ametek Gemco Displacement Cylinder |
| FRBKIT | Brake Parts | Ametek Gemco Fluid Reservoir Bleeder Kit including an AC or DC fluid reservoir bleeder assembly, a bleeder pushbutton and necessary tubing, fittings and brake fluid. |
| HM18X8-1 | Brake Parts | Ametek Gemco Hydraulic Brake System. Cab controlled Type HM Brake system with Parking Brake. Qty. 18 X 8 Brake, with Type HM Control Unit and Parking Brake Control Station, Fluid Reservoir Bleeder, Bleeder Push-Button, Control Cylinder & Pedal, Armored Hoses, 150 Feet of Tubing, Fittings & Brake Fluid. Specify whether bleeder check valve is to be controlled by 230 VDC / 115 Volt AC or Manually Operated via a 90 Degree Ball Valve |
| Hand Release | Brake Parts | Ametek Gemco Hand Release Option. Must be ordered with brake |
| J000086 | Brake Parts | Ametek Gemco Nut. Brass Tube Nut for the connection of flared copper tubing joints (1LB) |
| J000233 | Brake Parts | Ametek Gemco Brass Fastener Assembly. Bolt, Nut & Lockwasher for the 10 Inch Brake, 8 per lining |
| J000269 | Brake Parts | Ametek Gemco Outlet Fitting. 1/2 X 20 male thread at both ends. 1 end is for flared tubing the other end is flat like the end of the armored hose requires F17 copper gasket (<1LB) |
| J000363 | Brake Parts | Ametek Gemco Brass Bolt, Nut & Lockwasher for 14 & 18 Inch Brake Linings, 8 per 14 Inch Lining & 14 per 18 Inch Lining (<1LB) |
| J000387 | Brake Parts | Ametek Gemco Fastener. Brass Fastener Assembly. Bolt, Nut & Lockwasher for the 6 & 8 Inch Brake, 6 per 6 inch lining 8 per 8 Inch lining required. Ref Item 4. Sold each (<1LB) |
| J000391 | Brake Parts | Ametek Gemco Spring Clamp Tool for air releasing cylinders. |
| J001234 | Brake Parts | Ametek Gemco Lining. Brake Lining for a 14 Inch Hydraulic Brake. Lining has 8 Drilled & Countersunk holes for J000363 Brass Fasteners sold separately. Ref item # 23. 2 per brake. Sold each. 287DC Scan-Pak, Non Asbestos, MSDS Sheet Provided ( 7 LBS) |
| J001235 | Brake Parts | Ametek Gemco Brake Shoe & Lining for a 14 Inch Hydraulic Brake. Bonded linings with new pin & hardware. Qty. 1, 2 per brake assembly (23LBS) |
| J001276 | Brake Parts | Ametek Gemco Lining. Brake Lining for an 18 Inch Hydraulic Brake. Lining has 14 Drilled & Countersunk holes for J00363 Brass Fasteners sold separately. Ref item # 23. 2 per brake. Sold each. 288DC Scan-Pak, Non Asbestos, MSDS Sheet Provided ( 8 LBS) |
| J001396 | Brake Parts | Ametek Gemco Head Gasket, Head & Barrel to Control Cylinder Seal |
| J001768 | Brake Parts | Ametek Gemco Arm. Lever Arm on a 14 Inch Hyd brake. Ref item # 12. 1 per brake |
| J001803 | Brake Parts | Ametek Gemco Brake Shoe & Lining for a 18 Inch Hydraulic Brake, Qty. 1, 2 per brake (35LBS) ISG CLE 1231853 |
| J002395 | Brake Parts | Ametek Gemco Boot. Actuator Boot, Item 11, used on actuating cylinders J007905, J023437 & J008765 (1LB) |
| J002398 | Brake Parts | Ametek Gemco Brake Base for 6 or 8 Inch Hydraulic Brake ISG SAP 1094553 |
| J002680 | Brake Parts | Ametek Gemco Brake Base, 10 Inch Hydraulic ISG SAP 1094527 |
| J002681 | Brake Parts | Ametek Gemco Shoe Arm, 10 Inch Hydraulic ISG SAP 1087483 |
| J002682 | Brake Parts | Ametek Gemco Shoe Arm, 10 Inch Hydraulic ISG SAP 1087484 |
| J002683 | Brake Parts | Ametek Gemco Base for a 2929 14 Inch Brake ISG SAP 1094535 |
| J002684 | Brake Parts | Ametek Gemco Shoe Arm on a 14 Inch Brake, right side with provision for shoe centering lock kit ISG SAP 1087485 |
| J002685 | Brake Parts | Ametek Gemco Shoe Arm on a 14 Inch Brake with mount for hyd. cylinder ISG SAP 1087486 |
| J002686 | Brake Parts | Ametek Gemco 18 Inch Hyd Centering Spring |
| J002779 | Brake Parts | Ametek Gemco Brake Assembly. 8 X 3 Inch Hydraulic Brake Assembly, 200 to 450 FT LBS (30LB) |
| J002926 | Brake Parts | Ametek Gemco Brake Assembly. Hydraulic Brake, 10 Inch Diameter, Type H. Hydraulic Actuator and the Brake Wheel are not included (93LBS) |
| J002929 | Brake Parts | Ametek Gemco Hydraulic Brake Assembly. 14 Inch Type H, Less Hydraulic Actuator, 0 to 600 FT LBS on a Manual Brake System. 0 to 1400 FT LBS on a Air / Hydraulic Brake System.A 14 X 6 Inch Brake Wheel is not included (161LBS) |
| J002932 | Brake Parts | Ametek Gemco Brake Assembly, 18 X 8 Type H. Up to 900 LBS. / FT. dynamic stopping torque on a manual hydraulic brake system. 1800 LBS. / FT. dynamic stopping torque on a Air / Hydraulic brake system. 27.75 Inches Wide. 34.375 Inches high with brake applied. A hydraulic actuator and brake wheel are not included (266LBS) |
| J002935 | Brake Parts | Ametek Gemco Base. Brake Base on an 18 Inch Hydraulic Brake. Item 26, 1 per brake (40LBS) |
| J002936 | Brake Parts | Ametek Gemco Arm. Brake Shoe Arm on an 18 Inch Hydraulic Brake. Item 18, 1 per brake (20LBS) |
| J002937 | Brake Parts | Ametek Gemco Arm. Brake Shoe Arm on an 18 Inch Hydraulic Brake. Item 1, 1 per brake. Arm that has the actuator (20LBS) |
| J003054 | Brake Parts | Ametek Gemco Actuator. Type HM Hydraulic Actuator / Slave Cylinder on a 6 or 8 Inch Hyd Brake with the Parking Brake Option. Item 29A, 1 per brake (11LBS) ISG SAP 1085518 |
Fenton, MO 63026
Phone: (636) 537-0202
E:mail: [email protected]