Back___________________Next__________________Home
Buy Your Industrial Control Products Here!
Gemco Parts Description Page 24
| Part Number |
Product Category |
Description |
|---|---|---|
| E010077 | Brake Parts | Ametek Gemco Dust Seal for the Coil on a TM-1035. Old Westinghouse # 318B917H03 |
| E010078 | Brake Parts | Ametek Gemco Clapper on a TM-1035 Brake Assembly. Ref # 25. 1 per brake. 318B988G01 |
| E010079 | Brake Parts | Ametek Gemco Spring. Wheel End Spring on a TM-83 & 1035 Brake Tie Rod. Ref. # 10. 1 per brake. 438A070H13. Recommended spare part (1LB) |
| E010080 | Brake Parts | Ametek Gemco Main Spring on a TM1035 brake. Ref # 3. 1 per brake. Recommended spare part. 438A072H11 |
| E010083 | Brake Parts | Ametek Gemco Adjusting Screw Block on a TM1035 Brake. Ref # 7. 1 per brake. 438A217H01 |
| E010085 | Brake Parts | Ametek Gemco Spring. Tension Spring on a TM-1035 Brake, Ref. # 28. 2 per brake. Recommended spare part 438A411H03 (1LB) |
| E010086 | Brake Parts | Ametek Gemco Tie Rod on a TM1035 10 Inch Brake Assembly. Ref # 6. 1 per brake. 635C104G03 |
| E010096 | Brake Parts | Ametek Gemco Solenoid Guide, same as E007076, for a CB110 or 160 Brake Assembly |
| E010098 | Brake Parts | Ametek Gemco Rod. Adjusting Rod on a CB160 10 Inch Brake, 1 per brake. Ref # 17 , 3279B86G04 |
| E010103 | Brake Parts | Ametek Gemco Solenoid Assembly on a 10.00" Dia. CB160 Brake Assembly, includes the Plunger & Solenoid Guides, 3279B97H05 (8LBS) |
| E010106 | Brake Parts | Ametek Gemco Shoe & Lining. Brake Shoe & Lining, Inner Shoe for a CB160 10 Inch Electric Brake. 2254C28G04 |
| E010107 | Brake Parts | Ametek Gemco Shoe & Lining. Brake Shoe & Lining, Outer Shoe for a CB160 10 Inch Electric Brake. 2254C27G04 |
| E010108 | Brake Parts | Ametek Gemco Lining & Rivet Kit for a CB160 Brake, ( Drilled Lining with required Push Pins) 3279B95G04 |
| E010109 | Brake Parts | Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 2 Coils per brake assembly. 39.00 AMPS per coil continuous duty / 130 FT LB, 54 AMPS per coil intermittent duty / 200 Ft LB, average resistance.209 Ohms. Cost per coil brake requires 2 coils connected in series. Ref # 26 Old Westinghouse # 635C328G22 |
| E010109002 | Brake Parts | Ametek Gemco 13 Inch Brake with E0109002 Coils |
| E010111 | Brake Parts | Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 20.00 AMPS per coil continuous duty @ 130 FT LB, 27.5 AMPS per coil intermittent duty @ 200 FT LB. Average resistance .209 Ohms. 2 Coils per brake, cost per coil, coils are connected in series. Ref # 26 Old Westinghouse # 635C328G20 |
| E010114 | Brake Parts | Ametek Gemco Lining Kit, pair of drilled linings & fasteners for a TM1035, 10 Inch Diameter Brake, 861C691G17, 104-3445D ( 8 holes 10-10 Rivet Qty 18 ) |
| E010115 | Brake Parts | Ametek Gemco Outer Brake Shoe Arm on a TM-1035 Brake Assembly.Item 17. 635C306G01, 1 per brake. |
| E010116 | Brake Parts | Ametek Gemco Base Assembly for a TM-1035 brake assembly. Item 18. 1 per brake 635C300G01 |
| E010117 | Brake Parts | Ametek Gemco Arm. Inner Brake Shoe Arm on a TM-1035 Brake Assembly. Item 21. 635C306G02, 1 per brake |
| E010118 | Brake Parts | Ametek Gemco Clapper & Arm for a TM1035 Brake. 1 per brake. Ref # 22. 635C317G01 |
| E010119 | Brake Parts | Ametek Gemco Clapper Arm on a TM-1035 Brake Assembly. Ref # 24. 1 per brake. 635C308G01 |
| E010131 | Brake Parts | Ametek Gemco Actuator. Hydraulic Actuator for a ETH10 Brake Assembly. Actuator for cab control. 2 to 4 Weeks 11/04 |
| E010165 | Brake Parts | Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 75 Amps per Coil 1/2 Hour Rating. 55 Amps per Coil 1 Hour Rating. Resistance 0.0262 Ohms per Coil. Sold each / 2 coils per brake |
| E010193 | Brake Parts | Ametek Gemco Actuating Cylinder for a Electro-Hydraulic Brake. ETH-8 & ETH-10, H4-F-N 2.0" bore 1" Stroke, 1" rod, #4 Rod End, H4-F-N2.0X-1.00X1.00XXS13 Old price |
| E010237 | Brake Parts | Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1035 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
| E010266 | Brake Parts | Ametek Gemco Spring. Main Spring on a ET-10 Brake |
| E010286 | Brake Parts | Ametek Gemco Self Adjust Assembly Kit for an ET10 Brake |
| E010309 | Brake Parts | Ametek Gemco Tie Rod Assembly for an ET-10 Brake |
| E010326 | Brake Parts | Ametek Gemco Rectifier Assembly for a TM-43 through TM-1985 Brake Assembly. A NEMA 4 Enclosure is supplied. 16.0" H X 14.00" W X 8.0" D. An open chassis unit is available at less cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (54LBS) |
| E010327 | Brake Parts | Ametek Gemco Rectifier Assembly for a TM-43 through TM-1985 Brake Assembly. Open chassis design without enclosure. A NEMA 4 enclosure is available at additional cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (30LBS) |
| E010500 | Brake Parts | Ametek Gemco Brake Wheel, 10 Inch Diameter for the TM-1035 Brake, Stock Bore (40LBS) |
| E010622 | Brake Parts | Ametek Gemco Resistor External for a TM-1665 Brake Assembly, Old Westinghouse 47D0146G09 Ohms resistance required in line for 250 VDC 37.7 Ohms / 4.7 Amp |
| E010800 | Brake Parts | Ametek Gemco Brake Wheel for the CB-160 Brake Assembly. 10 Inch Diameter, 4.25 Inch Face Width, 4.26 Inch Offset when measured from the Centerline of the Face, 3.38 Inch Hub Length, 3.75 Inch Hub Diameter, Maximum Bore 2.25 Inch, Maximum RPM 4425, Solid Hub with the Bore Center Started, No pilot bore. ASTM A 536 Ductile Iron 80-60-03 or 80-55-06 Add $ 165.00 if you want BPI finish machine the Hub Offset, Length, Bore & Keyway |
| E011500 | Brake Parts | Ametek Gemco Brake Wheel, 11 Inch Diameter for the ET-11 Brake, Stock Bore (45LBS) |
| E013022 | Brake Parts | Ametek Gemco Resistor External for a TM-1355 Brake Assembly. STD 110.8 OHM 650 Watt. 250 VDC without discharge resistor. |
| E013023 | Brake Parts | Ametek Gemco Forcing Resistor for a TM-1355 Brake Assembly. 423A299G03 |
| E013025 | Brake Parts | Ametek Gemco Brake Shoe & Lining Complete for a TM1355 or ET13, 13 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 439C201G01 (12LBS) |
| E013026 | Brake Parts | Ametek Gemco Coil. Shunt Wound Coil for a TM-1355 Brake Assembly. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance per coil 19 Ohms. Cost per coil, brake requires 2 coils connected in series. Ref. # 26 637C384G16 |
| E013027 | Brake Parts | Ametek Gemco Bushing for a TM1355 Brake. Qty. 1, 6 per brake. 31D4114H12 (1LB) |
| E013028 | Brake Parts | Ametek Gemco Bushing for a TM1355 Brake. Qty. 1, 8 per brake. Ref # 19. 31D4118H06 (1LB) |
| E013029 | Brake Parts | Ametek Gemco Clapper on a TM-1355 Brake Assembly. Ref. # 25. 1 per brake. 318B560G01 |
| E013031 | Brake Parts | Ametek Gemco Seat. Wheel End Spring Seat on a TM1355 Brake assembly, 1 per Brake, 318B777H04 |
| E013032 | Brake Parts | Ametek Gemco Spring Clip on a TM-1355 Brake Assembly. Ref # 27 2 per brake. 318B778H04 (1LB) |
| E013033 | Brake Parts | Ametek Gemco Replaced by E013125 |
| E013034 | Brake Parts | Ametek Gemco Pin. Pivot Pin used on the TM1355 Brake. Sold each, 4 per brake. 318B789H04 (2LB) |
| E013035 | Brake Parts | Ametek Gemco Pin. Tension Spring Pin on a TM-1335 Brake Assembly. Ref # 29 1 per brake. 318B790H04 (1LB) |
| E013036 | Brake Parts | Ametek Gemco Block. Inner Hinge Block on a TM-1355 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H04 |
| E013037 | Brake Parts | Ametek Gemco Release Bushing on a TM1355 & TM1665 Brake Assembly, 1 per Brake, 318B792H04 |
| E013038 | Brake Parts | Ametek Gemco Stop for a TM1355 & TM1665 Brake. 318B794H04 9/6 (<1LB) |
| E013039 | Brake Parts | Ametek Gemco Main Spring Seat / Retainer on a TM1355 Brake Assembly, 1 per Brake, 318B795H04 |
| E013040 | Brake Parts | Ametek Gemco Seal. Dust Seal for coil on a TM-1355 Brake Assembly. 1 per brake. 318B917H04 (1LB) |
| E013041 | Brake Parts | Ametek Gemco Spring. Wheel End Spring on a TM1355 Brake Tie Rod. Ref No. 10 1 per Brake Recommended Spare Part 438A070H09 (2LBS) |
| E013042 | Brake Parts | Ametek Gemco Spring. Main Spring for a TM1355 13 Inch Brake, Coil End, 1 per Brake, 438A072H09 |
| E013044 | Brake Parts | Ametek Gemco Spring. Tension Spring on a TM1355 & TM1665 Brake, 438A411H05 (1LB) |
| E013045 | Brake Parts | Ametek Gemco Adjusting Screw Block on a TM1355 Brake. Ref # 7. 1 per brake. 438A456H01 |
| E013051 | Brake Parts | Ametek Gemco Bracket. Magnet Travel Equalizer Bracket on a TM-1355 Brake |
| E013052 | Brake Parts | Ametek Gemco Tie Rod for a TM1355 13 Inch Brake. Ref. #6, 1 per Brake. 861C691G18 |
| E013053 | Brake Parts | Ametek Gemco Brake Shoe Bolt on a TM1355, 2 per Brake, 24D6387G04. Item 3 |
| E013055 | Brake Parts | Ametek Gemco Lining Kit, pair of drilled & countersunk linings with fasteners for a TM1355, 13 Inch Diameter Brake. 861C691G18 (3LBS) |
| E013056 | Brake Parts | Ametek Gemco Clapper Arm on a TM-1355 Brake Assembly. Ref. # 24. 1 per brake. 439C203G01 |
| E013058 | Brake Parts | Ametek Gemco Coil. Series Coil for a TM13 Brake, 2 per brake, sold each, 637C551G16, 608 Mill Motor, 0.0358 Ohms Resistance Average, 85 Amps 1/2 Hour, 63 Amps 1 Hour (60 LBS) |
| E013059 | Brake Parts | Ametek Gemco Coil. Series Coil for a TM13 Brake, 2 per brake, sold each, 637C551G17, 606 Mill Motor, Ohms Resistance Average, Amps 1/2 Hour, Amps 1 Hour (60 LBS) |
| E013064 | Brake Parts | Ametek Gemco Arm. Outer Brake Shoe Arm on a TM-1355 Brake Assembly. Ref. # 17. 1 per brake. 439C192G05 |
Fenton, MO 63026
Phone: (636) 537-0202
E:mail: [email protected]