Back___________________Next__________________Home
Buy Your Industrial Control Products Here!
Gemco Parts Description Page 25
| Part Number |
Product Category |
Description |
|---|---|---|
| E013066 | Brake Parts | Ametek Gemco Base on a TM-1355 Brake Assembly. Ref. #18. 1 per brake. 439C204G01 |
| E013067 | Brake Parts | Ametek Gemco Inner Brake Shoe Arm on a TM-1355 Brake Assembly. Ref. #21. 1 per brake. old Westinghouse # 439C192G06 |
| E013068 | Brake Parts | Ametek Gemco Clapper & Arm for a TM1355 Brake. 1 per brake. Ref # 22. 489C202G01 |
| E013073 | Brake Parts | Ametek Gemco Spring Clip on a TM1355 Brake. Hand Release. 1 per brake. Old Westinghouse # 450A574H03 (1LB) |
| E013098 | Brake Parts | Ametek Gemco Coil. Series Wound Coil for a TM-1355 Brake. 637C551G23, 54 AMPS 1/2 Hour Rating, 40 AMPS 1 Hour Rating, .081 OHMS per coil, 2 per brake, sold each |
| E013125 | Brake Parts | Ametek Gemco Hinge Block on the Magnet End of a TM1355 Brake, 1 per Brake, 318B788H04 |
| E013146 | Brake Parts | Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1355 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
| E013194 | Brake Parts | Ametek Gemco Base for a ET13 Brake Assembly. item 1 |
| E013214 | Brake Parts | Ametek Gemco Main Spring on a ET-13 Brake E013214 & 04581104. Item 9A |
| E013225 | Brake Parts | Ametek Gemco Arm. Inner Shoe Arm on a ET-13 Brake. 1 Pair. Item 6 |
| E013228 | Brake Parts | Ametek Gemco Tie Rod Assembly for a ETH13EB50 Brake. Item 5 |
| E013229 | Brake Parts | Ametek Gemco Force Arm Assembly on a ET-13 Brake. Item 7 |
| E013231 | Brake Parts | Ametek Gemco Pin Kit for a ET-13 Brake. Includes Base Pins and Top Pins with Retaining Rings. Item 10 |
| E013240 | Brake Parts | Ametek Gemco Tie Rod. Self Adjust Tie Rod Assembly on a ET-13 Brake with the Self Adjust Option. Item 5A 4/7 |
| E013500 | Brake Parts | Ametek Gemco Stock Bore Brake Wheel, 13 Inch Diameter, for the TM-1355 Brake Assembly, 5.75" Face Width, 5.375" Offset when measured from the centerline of the face, 5.00" Hub Length Add $ 185.00 if you want BPI to finish machine the Hub Offset, Hub Length, Bore & Keyway (100LBS) |
| E013513 | Brake Parts | Ametek Gemco Brake Wheel 13 Inch Diameter with a hub length bore & keyway for an 808 Mill Motor with the AISE Standard Offset |
| E014500 | Brake Parts | Ametek Gemco Brake Wheel 14 Inch Diameter. Pilot Bore, TM & ET Brakes |
| E016022 | Brake Parts | Ametek Gemco Series Resistor for a TM-1665 Brake Assembly with Shunt Wound Coils. Old Westinghouse Part # 423A298G04 51 OHMS 250 VDC |
| E016023 | Brake Parts | Ametek Gemco Resistor. External resistor forced for a TM-1665 Brake Assembly. With taps set as specified on Ametek data sheet (5LBS) |
| E016025 | Brake Parts | Ametek Gemco Brake Shoe & Lining Complete for a TM-1665 or ET-16, 16 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Non-Asbestos Material Bonded to the Brake Shoe 635C227G01 (31LBS) |
| E0160251 | Brake Parts | Ametek Gemco Brake Shoe & Lining Complete, Bonded, for a TM1655 or ET16, 16 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, 635C227G01 |
| E016026 | Brake Parts | Ametek Gemco Shunt Coil for a TM-1665 Brake Assembly. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 8.8 Ohms. Cost is per coil brake requires 2 coils connected in series. Ref # 26 635C247G17 |
| E016027 | Brake Parts | Ametek Gemco Bolt. Brake shoe Bolt on a TM1655 & ET-16 Brake.Includes Bolt, Nut & Pin. Ref item 16. 2 per brake, 24D6387G03 (2LBS) |
| E016028 | Brake Parts | Ametek Gemco Pin on a TM1665 Brake, 1 per Brake, 318B571H05 |
| E016030 | Brake Parts | Ametek Gemco Spring Clip on a TM-1665 Brake Assembly. Ref # 27 2 per brake. 318B778H05 |
| E016031 | Brake Parts | Ametek Gemco Block. Wheel End Hinge Block on a Old TM1355 Brake Assembly, 1 per Brake, 318B787H05. New Style Brake uses a E016205 |
| E016033 | Brake Parts | Ametek Gemco Pivot Pin on a TM1665 Brake Assembly. Ref. # 20, 4 per brake. 318B789H05 |
| E016034 | Brake Parts | Ametek Gemco Pin. Tension Spring Pin on a TM-1665 Brake Assembly. Ref # 29 1 per brake. 318B790H05 (<1LB) |
| E016035 | Brake Parts | Ametek Gemco Block. Inner Hinge Block on a TM-1665 Brake Tie Rod. Ref. #4. 1 per Brake, 318B791H05 |
| E016036 | Brake Parts | Ametek Gemco Screw, Adjusting Screw on a TM1355 & 1665 Brake, 1 per Brake, 318B793H04 (1LB) |
| E016038 | Brake Parts | Ametek Gemco Seal. Dust Seal for coil on a TM-1655 Brake Assembly. 1 per brake. 318B917H05 (1LB) |
| E016039 | Brake Parts | Ametek Gemco Spring. Main Spring for a TM-1665 16 Inch Brake, Coil End, 1 per Brake, Recommended Spare Part 438A072H07 |
| E016040 | Brake Parts | Ametek Gemco Adjusting Screw Block on a TM1665 Brake Tie Rod. 438A352H01 |
| E016050 | Brake Parts | Ametek Gemco Clapper on a TM-1665 Brake Assembly. Ref #25. 1 per brake. 318B907G01 |
| E016051 | Brake Parts | Ametek Gemco Base on a TM-1665 Brake assembly. Ref. #18. 1 per brake. Old Westinghouse # 635C235G01 |
| E016052 | Brake Parts | Ametek Gemco Clapper & Arm on a TM-1665 Brake Assembly. Ref. #22. 1 per brake. Old Westinghouse #635C236G01 |
| E016053 | Brake Parts | Ametek Gemco Lining Kit, pair of linings & fasteners for a TM1655, 16 Inch Diameter Brake old 861C691G19. New brakes use bonded linings. 7 LBS Gross |
| E016054 | Brake Parts | Ametek Gemco Coil. Shunt Coil, Special Shunt Coil for a TM16 Brake, 2 per brake, sold each, 637C530G16, 808 / 610 Mill Motors, 0.0195 Ohms Resistance Average, 90 Volts Intermittent, 1 Hour / 125 Volts Continues Duty Cycle, 8 Hour. Specifications are for a single coil (100LBS) 7/7 |
| E016055 | Brake Parts | Ametek Gemco Series Coil for a TM-1665 Brake. Quoted each, 2 per brake. It is recommended that Series Coils are replaced in pairs. 637C530G19 7/7 |
| E016060 | Brake Parts | Ametek Gemco Outer Brake Shoe Arm with Bushings on a TM1665 Brake. Ref. # 17. 1 per brake. 635C240G01 |
| E016061 | Brake Parts | Ametek Gemco Inner Brake Shoe Arm with Bushings on a TM1665 Brake. Ref. #21. 1 per brake. 635C240G02 |
| E016062 | Brake Parts | Ametek Gemco Eyebolt, part of Hand Release Assembly on a TM-1665 Brake |
| E016063 | Brake Parts | Ametek Gemco Clapper Arm on a TM-1665 Brake Assembly. Ref. #24. 1 per brake. Old Westinghouse #635C238G01 |
| E016064 | Brake Parts | Ametek Gemco Handle, part of Hand Release assembly on a TM1665 Brake |
| E016065 | Brake Parts | Ametek Gemco Outer Block, part of the Hand Release Assembly on a TM-1665 Brake. Welded in place. |
| E016073 | Brake Parts | Ametek Gemco Hinge Block, Magnet End on a TM1665 Brake Assembly, |
| E016089 | Brake Parts | Ametek Gemco Actuator. Hydraulic Override Cylinder on a ETH-14 Brake Assembly. Slave cylinder for cab operation. |
| E016105 | Brake Parts | Ametek Gemco Tie Rod Assembly for a TM-1665 Brake. New larger diameter tie-rod completely populated with all components for installation on an older brake. Includes items 1 thru 6, 10 thru 12 and miscellaneous hardware. |
| E016108999 | Brake Parts | Ametek Gemco Hydraulic Actuator on a ETH-16 Thruster Brake with Slave Cylinder |
| E016200 | Brake Parts | Ametek Gemco Tie Rod on a TM1665 16 Inch Brake Assembly. Ref # 6. 1 per brake. Old Westinghouse 635C104G05 |
| E016203 | Brake Parts | Ametek Gemco Wheel End Spring Seat on a TM1665 Brake Assembly, 1 per Brake, 318B777H05 |
| E016205 | Brake Parts | Ametek Gemco Hinge Block, Wheel End Hinge Block on a TM1355 or TM-1665 Brake, 1 per Brake, new style 1/6 |
| E016206 | Brake Parts | Ametek Gemco Main Spring Seat on a TM1665 Brake Assembly, 1 per Brake, 318B795H05 |
| E016207 | Brake Parts | Ametek Gemco Spring. Wheel End Spring on a TM 1665 Brake Tie Rod. Ref No. 10 1 per Brake Recommended Spare Part (2LBS) |
| E016210 | Brake Parts | Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1665 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both |
| E016224 | Brake Parts | Ametek Gemco Block. Inner Tie Rod Block on a ETH14NA Brake |
| E016232 | Brake Parts | Ametek Gemco Pin. Pin for the Inner Tie Rod Block on a ETH14NA Brake. Includes Grease Fittings & Retaining Rings (<1LB) |
| E016500 | Brake Parts | Ametek Gemco Brake Wheel 16 Inch Diameter. Pilot Bore, TM & ET Brakes |
| E018500 | Brake Parts | Ametek Gemco Brake Wheel 16 Inch Diameter, Pilot Bore, TM & ET Brakes |
| E019022 | Brake Parts | Ametek Gemco Resistor. External resistor forced for a TM-1985 Brake Assembly |
| E019024 | Brake Parts | Ametek Gemco Brake Shoe & Lining Complete for a TM-1985 or ET-19, 19 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 439C394G01 (45LBS) 1/8 |
| E019025 | Brake Parts | Ametek Gemco Coil. Shunt Coil for a TM-1985, 19 Inch Brake Assembly. 2 Coils are used on this brake. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 8.5 Ohms. Coils are connected in series. Ref # 26. Price shown is for a single 1 coil 1/8 |
| E019027 | Brake Parts | Ametek Gemco Brake Shoe Bolt on a TM1985 or ET19 Brake Assembly. Page Ref. # 16. 2 per brake. 24D6387G01 1.25" Dia. X 10.5" L Rod threaded both ends 1 end has pin hole, Nut for use with pin, 1 pin. Nut is on & pinned (5 LBS) 8/7 2 Weeks |
| E019028 | Brake Parts | Ametek Gemco Bushing on the Shoe Clapper Arm for a TM1985 orTM2311 Brake, 2 per brake 31D4114H20 3/7 (<1LB) |
Fenton, MO 63026
Phone: (636) 537-0202
E:mail: [email protected]